Fisher-Price 79666 User manual

Model Numbers: 79666, B2109, B2110, B2111
Please keep this instruction sheet for future reference, as it contains important information.
Adult assembly is required.
Tools needed for assembly: Phillips Screwdriver (not included).
Product features and decorations may vary from the photo above.
D
i
s
c
o
v
e
r
w
h
a
t
’
s
p
o
s
s
i
b
l
e
™
…
w
w
w
.
f
i
s
h
e
r
-
p
r
i
c
e
.
c
o
m
Infant to Toddler
High Chair

2
Occasionally a consumer may experience a problem with
one of our products. If this should happen, please call us
toll-free, rather than return this product to the store. Usually,
we can solve the problem over the telephone or send you
replacement parts. Please call Fisher-Price® Consumer
Relations, toll-free at 1-800-432-5437,8AM- 6 PM EST
Monday through Friday. Hearing-impaired consumers using
TTY/TDD equipment, please call 1-800-382-7470.
Or, write to:
Fisher-Price®
Consumer Relations
636 Girard Avenue
East Aurora, New York 14052
For other countries, outside the United States:
Canada: call 1-800-567-7724,or write to: Mattel Canada Inc., 6155
Freemont Blvd., Mississauga, Ontario L5R 3W2.
Great Britain: telephone [phone].
Australia: Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870,
Richmond,Victoria 3121 Australia. Consumer Advisory Service 1300 135 312.
New Zealand: 16-18 William Pickering Drive, Albany 1331, Auckland.
Consumer InformationWarning
Prevent serious injury or death
from falls or sliding out.
•The child should be secured in
the high chair at all times by the
restraining system, either in the
recline, semi-recline or upright
position. The restraint belts must
be adjusted to fit your child
snugly. The tray is not designed
to hold the child in the chair.
•Always keep child in view while
in the high chair.
•Never leave child unattended.
•It is recommended that the high
chair be used in the upright
position only by children capable
of sitting upright unassisted.
WARNING

3
Parts
Rear
Support
2 Retainers
Front
Support
4 Legs
Seat with
Restraint System
Restraint Post
Footrest
2 Bases
2 Armrests
Pad
Tray
Seat Tube
ALL SHOWN ACTUAL SIZE
2 Leg Caps
#8 x 3/4" Screw - 7
#8 x 15/8" Screw - 2
#10 Lock Nut - 4
#8 Lock Nut - 2
#10 x 21/8" Screw - 4
IMPORTANT! All consumer assembled
screws must be fully tightened for
proper assembly of this product.

Assembly
4
IMPORTANT! Before each use or assembly, inspect this product
for damaged hardware, loose joints, missing parts or sharp
edges. DO NOT use if any parts are missing or broken. Contact
Fisher-Price® for replacement parts and instructions if needed.
Never substitute parts.
Legs
Notch
Notch
Base Tubes
Numbers
1
•Fit a leg cap into the openings of two legs, as shown.
•Push down on the leg cap to be sure it is secure, and there
is no gap between the top of the legs and the leg cap.
•Repeat this procedure to attach the other leg cap to the
other two legs.
Legs
Leg Cap
2
Leg Cap
Track
Armrest
3
•Position a base so that the notches face you.
•Position two legs so that the numbers face you.
•Fit a leg onto each base tube.
•Twist and push each leg until it "snaps" into each base tube.
•Repeat this procedure to assemble the remaining two legs to
the other base.
•Position an armrest so that the track is facing out.
•Fit the armrest onto a leg cap, as shown.
•Repeat this procedure to attach the other armrest to the
other leg cap.
This product contains small parts
in its unassembled state. Adult
assembly is required.
CAUTION

Assembly
5
•Turn the leg assembly, as shown, so that the armrests point
toward you.
•Position the front support so that the arrows are pointing
toward you.
•Fit the ends of the front support up between the inside of the
armrests and the front legs.
Armrest
Front
Leg
Front Support
Arrows
5
•Insert a #10 x 21/8" screw through the outside of an armrest,
a rear leg and then out through the inside of the armrest.
•Fit a #10 lock nut into the hexagonal opening on the inside
of the armrest. Make sure the rounded side is facing out.
•Fully tighten the screw with a Phillips screwdriver. When
properly tightened, the end of the screw will be visible,
as shown above.
•Repeat this procedure to secure the other armrest with a
#10 x 21/8" screw and a #10 lock nut.
Armrest
Rear Legs
#10 Lock Nut
#10 x 21/8" Screw - 2
Shown Actual Size
#10 Lock Nut - 2 Rounded Side
Shown Actual Size
End
of Screw
Visible
Lock Nut
4

Assembly
6
•While holding the front support in place, insert #10 x 21/8"
screw through the outside of an armrest, front leg, front sup-
port and then out through the inside of the armrest.
•Fit a #10 lock nut into the hexagonal opening on the inside of
the armrest. Make sure the rounded side is facing out.
•Fully tighten the screw with a Phillips screwdriver. When
properly tightened, the end of the screw will be visible,
as shown above.
•Repeat this procedure to fasten the front support to the other
armrest with a #10 x 21/8" screw and #10 lock nut.
#10 Lock Nuts
Front
Leg
Front
Support Front
Leg
6
7
•Position the seat face down on a flat surface.
•Insert the seat tube through the a rectangular slot, the two
circular slots in the recline bar and then out through the other
rectangular slot.
Circular Slots Seat Tube
Rectangular Slots
Recline Bar
8
•Align the arrows on the seat tube with the arrows on the
recline bar.
Turn
Seat Tube
to Align
Arrows
Recline
Bar
#10 x 21/8" Screw - 2
Shown Actual Size
#10 Lock Nut - 2 Rounded Side
Arrows on
Seat Tube
Arrows on
Recline Bar
Shown Actual Size
End
of Screw
Visible
Lock Nut

Assembly
7
•Face the back of the seat assembly.
•First, fit the left end of the seat tube into the lowest opening
in the left armrest.
•Then, fit the right end of the seat tube through the notch
in the right armrest and then into the lowest opening in
the armrest.
Left End of
Seat Tube
Right End
of Seat
Tube
Notch
Lowest Openings
10
Back View
•At an angle, fit the seat between the armrests.
•Now, fit the grooves in the seat tabs to the front support.
Seat
Front Support
Grooves
Armrest
Armrest
9

Assembly
8
•Align the arrows on the seat tube with the arrows on the
recline bar.
•Insert a #8 x 3/4" screw through the hole in the recline bar
and into the seat tube. Fully tighten the screw with a Phillips
screwdriver.
Seat
Tube
Hole
11
•Squeeze the seat recline and
push the seat back forward to
the most upright position.
12
Shown Actual Size
#8 x 3/4" Screw
Upright
Squeeze
Seat
Recline
Arrows on
Seat Tube
Arrows on
Recline Bar

Assembly
9
•Insert four #8 x
3/4"
screws
through the footrest and into
the seat tabs.
•Fully tighten the screws with
a Phillips screwdriver.
14
Shown Actual Size
#8 x 3/4" Screw - 4
•Fit the footrest over the front support and onto the long
and short tabs on the seat.
13
Footrest
Front Support
Short Tab
Short Tab Long Tabs

Assembly
10
•Position the assembly upright.
•At an angle, insert the large tab on the restraint post into the
slot between the seat and the footrest.
•Then, push to “snap” the restraint post into the large opening
in the footrest.
15
Restraint
Post
•Position the assembly face down.
•Insert a #8 x 3/4" screw through each
end of the seat and into
the footrest.
•Fully tighten the screws with a Phillips screwdriver.
16
Shown Actual Size
#8 x 3/4" Screw - 2
•Face the back of the assembly.
•Position the rear support so that it bends upright.
•Align the screw holes in the rear support with the screw holes
in the rear legs.
•Now, place a retainer over each end of the rear support.
•Insert a #8 x 15/8 " screw through the outside of each rear leg,
the rear support and into the retainer.
•Fit a #8 lock nut into the hexagonal opening in the retainers.
Make sure the rounded side is facing out.
•Fully tighten the screws with a Phillips screwdriver. When
properly tightened, the end of the screw will be visible,
as shown above.
Rear
Support
Retainers
Seat
Footrest
#8 x 15/8" Screw - 2
Shown Actual Size
17
#8 Lock Nut - 2 Rounded Side
Shown Actual Size
End
of Screw
Visible
Lock Nut
Back View

Assembly
11
•Place the pad onto the seat
•Insert the two top elastic straps through the slots labeled 1
in the head supports.
Seat
Pad
Elastic
Straps
18
•Lift the head supports to locate the large hole in the seat
back labeled 2.
•Insert the elastic straps through the large holes labeled 2.
Elastic Straps
19
Head Support
Head Support
•From behind the seat, hook the elastic straps over the tabs
labeled 3.
20
.• From the front of the seat,
fit the top pocket on the
back of the pad over the
top of the seat.
•From the back of the seat, fit the top edges of the pad around
the head support levers.
•Press the center of the pad to fasten it to the seat.
21
Tabs
Elastic Straps
Top of Pad
Head Support Levers
Back View
Back View
Press

Assembly
12
•Lift the bottom of the pad.
•Fit the elastic straps through
the in slots the seat bottom.
•From the back of the seat, fit the elastic straps onto the tabs,
as shown.
22
Elastic
Straps
Tabs
Slot
Slot
•Fit the waist belts through the two upper slots in the pad.
•Fit the crotch belt through the lower slot in the pad.
Crotch
Belt
Lower
Slot
Waist
Belt
Waist
Belt
23
Upper
Slots
•From behind the seat, hook the elastic straps onto the posts,
as shown.
Posts
•Fit the elastic straps on the edge of the pad through the slots
in the footrest.
Slots
Elastic Straps
25
24
Back View
Back View

13
Securing Your Child
•Place your child in the seat. Position the crotch belt between
your child’s legs.
•Fasten both waist belts to each side of the crotch belt. Make
sure you hear a "click" on both sides.
•Check to be sure the restraint system is securely attached by
pulling it away from your child.The restraint system should
remain attached.
Crotch
Belt
Waist Belts
IMPORTANT! Before each use, inspect this product for
damaged hardware, loose joints, missing parts or sharp edges.
DO NOT use if any parts are missing or broken. Contact
Fisher-Price® for replacement parts and instructions if
needed. Never substitute parts.
Prevent serious injury or death
from falls or sliding out.
The child should be secured in
the high chair at all times by the
restraining system. The restraint belts
must be adjusted to fit your child
snugly. The tray is not designed to
hold the child in the chair.
WARNING
1
To tighten the waist belts:
•Feed the anchored end of the waist belt up through the
buckle to form a loop .
A
•Pull the free end of the waist belt .
•Repeat this procedure to tighten the other waist belt.
B
To loosen the waist belts:
•Feed the free end of the waist belt up through the buckle to
form a loop .
•Enlarge the loop by pulling on the end of the loop toward
the buckle.
•Pull the anchored end of the waist belt to shorten the free
end of the waist belt .
•Repeat this procedure to loosen the other waist belt.
B
A
Buckle
Buckle
2
3

14
Using the Tray
•Fit the tray onto the armrests, as shown. Push down until the
tray “snaps” into place.
•Test to be sure the tray is secure on the armrests. Push the
tray back and forth. It should not move.
Armrest
Armrest
Prevent serious injury or death
from falls or sliding out.
The child should be secured in
the high chair at all times by the
restraining system. The restraint
belts must be adjusted to fit your
child snugly. The tray is not
designed to hold the child in
the chair.
WARNING
1
Hint: Before use, thoroughly wash the tray.
•While pushing the button on the front of the tray, adjust the
tray forward or backward. Make sure it locks into position.
•To remove the tray, push the button on the front of the tray
and slide it forward and off the armrests.
Slide
Forward
to Remove
Adjust
Forward or
Backward
Push
2

To adjust the seat height:
•Press the height lever on the front base and lift or lower the
seat to the desired height.
•Makesure both front legs are adjusted to the same height.
•Press the height lever on the rear base and lift or lower the
seat to the same height as the front legs.
•Makesure both rear legs are adjusted to the same height.
•Push the seat bottom to be sure all four legs are locked
in place.
IMPORTANT! Make sure the number that shows in each notch in
the front an back bases are the same for all four legs.
Prevent serious injury or death
from falls or sliding out.
It is recommended that the high
chair be used in the upright
position only by children capable
of sitting upright unassisted.
WARNING
Adjusting the Seat Height
Notch
Height
Position
Number
Push
Height Lever
Hint: Adjust the seat height to any of three positions 1, 2 or 3.
Adjusting the Seat Angle
To adjust the seat angle:
•Squeeze the seat recline and
push the seat back forward or
pull it backwards to the
desired position.
•Push the seat back to be sure it
is latched in position.
IMPORTANT! When the seat is in the recline positions, be
sure the tray is secure on the armrests. Push the tray back
and forth. It should not move.
Recline
Upright
Squeeze
Seat
Recline
Hint: Adjust the seat angle in any of four positions: Upright,
Semi-Upright, Semi-Recline or Recline.
15

•The pad is machine washable. Wash the pad separately in cold
water on the gentle cycle. Do not use bleach. Tumble dry
separately on low heat and remove promptly.
•The frame and tray may be wiped clean using a mild cleaning
solution and a damp cloth. Do not immerse the tray.
To remove the pad:
•Remove the six elastic loops from the pegs on the back of the
seat and underside of the footrest.
•Remove the pad upper pocket from the seat back.
•Feed the waist straps through the slots in the pad and the seat.
•Feed the waist straps through the slot in the pad and the seat.
•Remove the pad from the seat.
To replace the pad, refer to Assembly steps 18-25.
IMPORTANT! Never use this product without the
restraint system.
Care
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A. Printed in Mexico
©2002 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc. 79666pr-0920
Using the Head Supports
Headrest
Lever
Headrest
Lever
• Press the head support levers to raise supports.
Press to
Raise
Supports
Press to
Raise
Supports
Headrest
Lever
Headrest
Lever
•Lift the head support levers to lower supports.
Lift to
Lower
Supports
Lift to
Lower
Supports