KRAFTWERK 3984 User manual

Art. 3984
Instruction Manual
Rolling work seat
EN
max.
135 kg

2
SAFETY & GENERAL INFORMATION
For your safety, read, understand, and follow the information provided with and on this Rolling work seat. The owner
and operator shall have an understanding of this product and safe operating procedures before attempting to use.
The owner and operator shall be aware that use of this product may require special skills and knowledge. Make
certain that the operator thoroughly understands the inherent dangers associated with the use and misuse of the
product. If any doubt exists as to the safe and proper use of this product, remove from service immediately.
Inspect before each use. Do not use if there are broken, bent, cracked or damaged parts (including labels).
Any seat that appears damaged in any way, or operates abnormally shall be removed from service immediately.
If the seat has been subjected to a shock load (a load dropped suddenly, unexpectedly upon it), immediately
discontinue use until it has been inspected by KRAFTWERK authorized service center. It is recommended that an
annual inspection be done by qualified personnel. Labels and Operator’s Manuals are available from manufacturer.
PRODUCT DESCRIPTION
Easy rolling Ø75mm swivel composite castors.
* Rated Capacity: One (1) person weighing 135 kg. or less- includes person, tools, equipment, personal items.
SPECIFICATIONS
Do not use this device for any purpose other than that for which it is expressly intended.
Model Capacity Wheels Size
3984 *135 kg 5 450 x 450 x 450 mm
ABC
EFG
HI J K
Magnetic pad Sub-frame
14 mm Nut Spring washer Washer
Tray divider
Cylinder
Height Adj. LeverSeat1x
1x
5x 5x 5x 5x
1x 1x
1x 1x 1x
D
PARTS LIST:
Tray
Caster

3
• This seat may tip over if any caster wheel(s) are caught in a crack, seam, on a rock, pebble
or other obstacle, or when used on soft carpeted floors.
• Be cautious when moving the seat while seated on it.
USAGE
RAISING THE SEAT：Once the seat top is securely attached to the pneumatic ram, lift the height adjustment lever
(B) wihtout putting any weight on the seat. This will raise the seat to its maximum height.
LOWERING THE SEAT: Pull up on the adjustment lever while sitting on the seat to lower it to its lowest height. The
seat can be adjusted to any height by releasing the adjustment lever at the desired height.
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list. If
any part is missing or damaged, do not attempt to assemble, install or operate the product. Contact customer service
for replacement parts.
Dimensions: 450 x 450 x 450 mm
ASSEMBLY DIAGRAM & ASSEMBLY INSTRUCTIONS
WARNING
A
B
C
E
I
J
K
F
H
G
D
• Unpack all parts before discarding/recycling the packaging
material.
Adjustable Wrench or 14mm open end or socket
• Assemble the casters (H) to the tray (F), sub-frame (G), and tray
divider (D) as shown, and tighten.
• Place the pneumatic cylinder (C) into the base as shown.
• Place the seat top (A) onto the pneumatic cylinder ram as shown.
NOTE: The pneumatic cylinder is taper fit to the base and seat top
and requires no hardware. Please check that the connecting
surfaces are clean and dry before assmbly.
Firmly press down on seat. Lift the seat by the top cushion
to ensure positive connection.
TOOLS REQUIRED FOR ASSEMBLY
ASSEMBLY INSTRUCTIONS

CARE AND MAINTENANCE
MAINTENANCE
Little maintenance is required of this device. Wipe clean as needed. Use mild upholstery cleaner (not caustic) to
clean seat as needed.
Never add lubricant to casters!
www.kraftwerktools.com
KRAFTWERK Europe AG
Mettlenbachstrasse 23
CH-8617 Mönchaltorf
Switzerland
Tel. [phone]
KRAFTWERK Sàrl.
25, rue du Stade
F – 67870 Bischoffsheim
France
Tel. [phone]
WARRANTY
We do not take responsibility for any damage caused by misuse or any use that is not in compliance
with the safety standards described herein.
CUSTOMER SERVICES
Contact your local importer of your specialized dealer to obtain address of our service department.
FROM DATE OF PURCHASE RECEIPT
2 YEAR GUARANTEE
ON MATERIAL OR PRODUCTION DEFECTS