Kramer FC-7P User manual

FC-7P Quick Start (P/N: 2900-300615QS REV 1)
P/N:
2900- 300615QS
Rev:
1
Scan for full manual
FC-7P Quick Start Guide
This guide helps you install and use your FC-7P for the first time.
Go to www.kramerav.com/downloads/FC-7P to download the latest user manualand checkiffirmware
upgrades are available.
Step 1: Check what’s in the box
FC-7P Ethernet Gateway
4 Rubber feet
1 Bracket set
1 USB-A to USB mini cable
1 Quick start guide
Step 2: Get to know your FC-7P
#
Feature
Function
1
LINK LED
Shows the Ethernet link is active
2
Activity LEDs
Ports 1 and 2, white (upper) and
blue (lower)
Show the transmission status of port 1 and port 2:
When set as GPIO, the white LED indicates active IO-P1 and blue LED indicates active IO-P2
When set as RELAY, the white LED indicates active Relay-P1 and blue LED indicates active
Relay-P2
3
MODE DIP-switches
(Port 1 and Port 2)
Switch up (off) for GPIO, switch down (on) for relay
The default setting is port 1 GPIO (up) and port 2 relay (down)
4
ON LED
Lights green when the unit is on
5
Port 1 I/O 3-pin Terminal Block
Port 1 terminal block port connects to two GPIO ports or two relays
6
Port 2 I/O 3-pin Terminal Block
Port 2 terminal block port connects to two GPIO ports or two relays
7
RESET Button
Press and hold while cycling the device power to reset to factory default parameters
8
ID
Press to broadcast ID message for auto-discoveryof the device
9
LAN/POE RJ-45 Connector
Connects to a PoE source (Power over Ethernet) for powering and an IP client or other
controller, either directly or via a LAN
10
SERVICE Mini USB Connector
Connects to a USB power source for powering and to a PC for a local firmware upgrade
11
5V DC Connector
For extra power resiliency, connect to the optional 5V DC power supply, center pin positive.
Not needed when the device is suppliedpowerby PoE or a USBpower source

Step 3: Install the FC-7P
You can mount this Kramer TOOLS™ next to a USB power source behind an
AV device, within the ceiling, on a desk top, wall or similar area. Fasten a
bracket on each side of the TOOLS using the two M3x8 screws (supplied).
Use the flat-head screws (supplied) to fix the TOOLS to the mounting surface
or enable it to slide in place.
Or you can attach the rubber feet and place on a table or mount the FC-7P in
a rack (using an optional RK-3T rack mount).
Step 4: Connect the inputs and outputs
Always switch OFF the power on each device before connecting it to your FC-7P. For best results, we recommend that you always
use Kramer high-performance cables to connect controlled equipment to the FC-7P.
Step 5: Connect the power
Connect the PoE or USB power source and/or an optional 5V DC power supply to the FC-7P and plug it into the mains electricity.
Step 6: Configure and operate the FC-7P
Note: The FC-7P is shipped from the factory with DHCP enabled and a random IP address. To connect the FC-7P on first
installation, you must identify what IP address has been automatically assigned to the FC-7P. To discover the IP address of
FC-7P, use K-LAN Configurator, available for download from our website at www.kramerav.com.
To reset the device to its factory default settings:
1. Turn off the power to the device.
2. Press and hold the Reset button on the rear panel.
3. Turn on the power to the device while holding down
the Reset button for a few seconds.
4. Release the button.
The device is reset to the factory default settings.
To browse the FC-7P Web UI (User Interface) using
factory default settings:
Use the default host name: FC-7P-xxxx, where xxxx are
the last four digits of the serial number of the device.
FC-7P Function Table
To configure and operate the FC-7P:
1. Using the device Web UI, configure the control gateway:
• Set DHCP or assign a static IP address
• Associate IP port(s) with the relevant port(s)
• Configure the relevant port parameters
2. Configure IP client connection port(s) on a Kramer control or
any other control software application.
3. Set the control application to use the control gateway ports for
sending and receiving control communication over the IP
connections.
Key: P1 / P2 –Port 1 / Port 2; IO1 / IO2–GPIO Port 1 / GPIO Port 2; NO1/NO2 –Normally open Port 1 / Normally open Port 2
Port IO
Function
Terminal Block Connections
IO Port Default
TCP Default
Port [P1/P2]
Activity LEDs
P1-white P2-blue
Comment
G
P1
P2
GPIO
Ground
IO1
IO2
Digital In x 2
5000
ON when IO
ports are active
GPIO Analog in &
Digital out via Web
Relay
Common
NO1
NO2
Normally Open x 2
5000
ON when Relay
ports are active