Kramer MegaEdge Series User manual

MegaEdge Quick Start
P/N:
2900- 301232QS
Rev:
3
Scan for full manual
MegaEdge Quick Start Guide
This guide helps you install and use your MegaEdge for the first time.
Go to www.kramerav.com/downloads/MegaEdge to download the latest user manual and check if firmware
upgrades are available.
Step 1: Check what’s in the box
MegaEdge Secure Portable Power Supply
1 T20 Torx bit
4 4x1/2” screws
Retractable AC Power Cord Reel
2 T20 Torx security screws
1 Quick start guide
Step 2: Get to know your MegaEdge
MegaEdge-US
220/240V AC universal outlets on
MegaEdge-WW
#
Feature
MegaEdge-US Function
MegaEdge-WW Function
1
AC Power Connector
(x2)
Connect to up to two 120V AC power
consuming devices simultaneously.
Connect to up to two 220/240V AC power
consuming devices simultaneously.
When a single power socket is connected, consumption should not exceed 5A. When both
power sockets are connected, the total consumption should not exceed 6A.
2
5V-2A USB Fast
Charging Port (x2)
Use to charge a mobile device.
3
USB-C
Use to charge a mobile device.
4
Control Button
Short press to turn MegaEdge On.
Once on, each additional short press toggles MegaEdge AC power outlets On/Off
MegaEdge consumes some power when the AC power indicator is on even when no
devices are connected to it.
Long press to turn MegaEdge Off.
5
Power On Indicator LED
Lights blue when MegaEdge is on.
6
Numeric LED Display
Indicates percent of power remaining.
7
AC Indicator LED
Lights red when AC power enabled.
USB DC power is always on when MegaEdge is on.
8
Mounting Bracket
Used with security screw for securing the MegaEdge to the table.
9
Security Screw (2)
For securing the MegaEdge to the table.

Step 3: Install MegaEdge
Install MegaEdge
1. Carefully place MegaEdge over the edge of a table
at the desired location so that the table edge is
pressed against the device.
2. Secure MegaEdge to the table using the Torx bit and
the two security screws provided.
3. Tighten each security screw through the MegaEdge
mounting bracket into the table.
Install Retractable AC Power Cord Reel
1. Attach the Reel Mounting Bracket under the table
using the four screws (provided) so that the
Retractable AC Power Cord Reel’s fixed plug can
easily reach the MegaEdge AC socket (less than
50cm distance).
2. Press the Retractable AC Power Cord Reel to the
Reel Mounting Bracket and rotate clockwise until you
hear a click.
3. Plug the Retractable AC Power Cord Reel’s fixed
plug into MegaEdge.
Reel Mounting Bracket
Retractable AC Power Cord Reel
Step 4: Connect power
To fully charge MegaEdge, connect the Retractable AC Power Cord Reel power cord to the mains electricity for at least 8
hours.
Safety Instructions (See www.kramerav.com for updated safety information)
Caution:
•There are no operator serviceable parts inside the unit.
Warning:
•Use only the power cord that is supplied with the unit.
•Disconnect the power and unplug the unit from the wall before installing.
•Do not open the unit. High voltages can cause electrical shock! Servicing by qualified personnel only.
•To ensure continuous risk protection, replace fuses only according to the rating specified on the product label which located on the
bottom of the unit.
Step 5: Operate MegaEdge
To Turn MegaEdge On
•Press the Control button.
Power On LED lights blue.
To Turn MegaEdge Off
•Press the Control button for 3 seconds.
Power On LED is no longer lit.
To Toggle AC Power On/Off
•Press the Control button to toggle between AC power On and AC power Off
AC LED is lit red when AC is on.
MegaEdge consumes some power when the AC power indicator is on even when no devices are connected to the AC.
When no power is being used, MegaEdge powers off automatically after 1 minute.
To Charge MegaEdge
When not in use, extend the AC plug from the Retractable AC Power Cord Reel and plug it into an AC outlet for at least 8
hours to fully charge the MegaEdge.