Kraus Britt KPF-1690BG User manual

Britt Single Handle
Commercial Kitchen Faucet
KPF-1690
TM
R
INSTALLATION GUIDE
www.kraususa.com I Toll Free: 1.800.775.0703 I © 2018 Kraus USA Inc. I REV. December 10, 2020

Congratulations on the purchase of your new
Kraus plumbing fixture!
Please keep the box and packaging materials until your product is
completely installed. If you have any questions, require technical
assistance or have any problems with your product:
2
Please contact our Customer Service Team
1-800-775-0703 / [email protected]
Have the model number available and retain a copy of your receipt
with purchase date for reference.
If for any reason this product does not meet your expectations,
please be sure to repack this product in the original box and
packaging material to avoid damage during transit.
DO NOT RETURN TO STORE
STOP

Prior to Installation:
·Make sure you have all necessary parts by checking the diagram and
parts list. If any part is missing or damaged, please contact Kraus
Customer Service at 800-775-0703 for a replacement.
·Turn off the hot and cold water supply at the angle stops and turn on
the old faucet to release any built up pressure. Remove existing faucet.
Clean sink or countertop to remove any debris, plumber’s putty, or
silicone.
·Place bucket under angle stops. Turn on angle stops to flush any
debris prior to installing new plumbing. Shut off angle stops.
·Max countertop thickness: 3”
·Pre-drilled hole size requirement: 1 3/8"
·1 or 3 hole installation
3
For technical assistance or replacement parts, please contact Kraus
Customer Service and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or [email protected]
Tools you will need:
Adjustable Wrench Bucket Phillips Screwdriver Safety Goggles

44
Diagram and Parts List
A. Spray Head
B. Faucet Body
C. Mounting Hardware
C1. Rubber & Metal Washer
C2. Mounting Nut
C3. Mounting Screw
D. Flange & Washer
E. Escutcheon
F. Base Plate
G. Escutcheon Mounting Hardware
G1. Bolt
G2. Plastic Nut
H. 2.5 mm Hex Wrench
B
A
H
E
F
G1
G2
D
C1
C2
C3

55
Faucet Dimensions
3/8" Compression
20 5/8"
(524mm)
1 3/4"
(46mm)
4 5/8" (116.6mm) 10 3/4" (271.6mm)
6 3/8"
(162mm)
8 1/2"
(215mm)
2 3/8"
(60.6mm)
Ø1 3/8" (34mm)
10" (255.6mm)
1/4"
(7.9mm)
* Optional Deck Plate
R1 1/4"
(30.3mm)
MAX 3"
(76mm)
1/4"
(7.9mm)

66
Step 1. Remove mounting hardware
Step 2. Install the faucet assembly (without deckplate)
Shut off the water supply.
Remove the old faucet. Clean
the mounting surface. Remove
mounting hardware (C) from
faucet body (B).
Before installation, ensure that the
flange (D) is placed on the bottom
of the new faucet assembly (B).
Insert the faucet body through the
hole in the sink.
NOTE: Skip this step and move
on to Step 3 if installing with
deckplate.
C
B
D

7
Step 3. Install the escutcheon
Step 4. Install the faucet assembly (with deckplate)
Before installation, remove the
flange (D). Screw the bolts (G1) into
the escutcheon (E) and
ensure that the base plate (F)
is pressed onto the escutcheon
(E) before the escutcheon (E) is
installed over the three holes on the
sink. From underneath the sink, hand
tighten the mounting nuts (G2).
Do not overtighten.
NOTE: Skip this step if installing
without deckplate.
Insert the faucet assembly (B)
through the hole in the
escutcheon (E).
NOTE: Skip this step if installing
without deckplate.
E
G1
F
G2
B
E

8
Step 5. Secure the faucet assembly
Step 6. Connect the waterlines
Install the plastic washer and metal
washer (C1) onto the threaded
mounting shank. Thread the nut
(C2) onto the mounting shank.
Lock the nut (C2) into position by
tightening the screws (C3).
Do not overtighten.
Thread the nut (1) on the supply line
onto the outlet of the water supply
valve (2) and tighten with wrench.
Do not overtighten.
C1
C2
C3
1
2

9
Step 7. Flush and check for leaks
Pull hose assembly out of spout
and remove spray head by
unscrewing from hose in a
counterclockwise direction.
Hold the end of the hose down
into the sink and turn the faucet on
to the warm position. Flush water
lines for one minute to flush away
any debris. Check for leaks.
Re-tighten any connections if
needed. Do not overtighten.
Reinstall spray head by hand
tightening it back onto the spray
hose. After installation is completed,
turn on the hot and cold water
supplies to check for leaks.

10
Replacement Parts
1. Spray Head
2. 1.8 GPM Washer
3. Sprayer Hose
4. Inverter
5. Spring
6. Inverter
7. O-ring
8. Block
9. Washer
10. Spray Support
Assembly
11. Set Screw
12. Cartridge
13. Bonnet Nut
14. Cap
15. Handle
16. Set Screw
17. Cover Button
18. Rubber &
Metal Washer
19. Nut & Screw
20. Flange
21. Escutcheon
22. Escutcheon
Mounting
Hardware
23. Filter Washer
Replacement Finish/Color Part #
Parts List
KP27195
KP27196
KP27025
KP27026
KP27027
KP27080
KP27029
KP27030
KP27031
KP27032
KP27033
KP27035
KP27036
KP27037
KP27038
KP27001
KP27002
KP27028
KP27041
KP27184
5
6
4
7
8
9
11
3
2
114
18
19
20
21
22
12
13
15
16
17
10
*Denotes faucet component color options:
SFS - Spot Free Stainless Steel
MB - Matte Black
BG - Brushed Gold
SFACB - Spot Free Antique Champagne Bronze
SFSB - Spot Free Black Stainless
AB - Antique Brass
BL - Black
GR - Gray
KP27185
GR,BL*
SFS,BG,SFACB,SFSB,AB*
SFS,BG,SFACB,SFSB,AB*
SFS,BG,SFACB,SFSB,MB,AB*
KP27079
BLAB,BLBG,BLSFSB
SFS,AB,BG,SFSBMB
SFACBMB,BGMB*
KP27167
23
GR,BL*
GR,BL*
GR,BL*
BLMB,BLSFACB,SFS*
SFS,BG,SFACB,SFSB,AB*
SFS,BG,SFACB,SFSB,AB*
SFS,BG,SFACB,SFSB,AB*