Kraus Oletto KPF-2600 User manual

Oletto™ Single Handle Kitchen Bar Faucet
KPF-2600
INSTALLATION GUIDE
www.kraususa.com I Toll Free: 1.800.775.0703 I © 2022 Kraus USA Plumbing LLC I REV. Jul 18, 2022

1
Congratulations on the purchase of your new
Please keep the box and packaging materials until your product is
completely installed. If you have any questions, require technical
assistance, or have any problems with your product:
Please contact our Customer Service Team
1-800-775-0703 / [e-mail]
Have the model number available, and retain a copy of your receipt
with purchase date for reference.
If for any reason this product does not meet your expectations,
please be sure to repack this product in the original box and
packaging material to avoid damage during transit.
DO NOT RETURN TO STORE

2
Prior to Installation:
•Make sure you have all necessary parts by checking the diagram and parts list. If
any part is missing or damaged, please contact Kraus Customer Service at 800-775-
0703 for a replacement
•
•
Pre-drilled countertop hole size requirement: 1-3/8”(min)
•
Max countertop thickness: 2 3/8”
Tools you will need:
Wrench Phillips Screwdriver Safety Goggles
Silicone Sealant
(optional)
Pipe Tape
Turn o the hot and cold water lines at the angle stops and turn on the old faucet
to release any built-up pressure
STOP
•
Read all instructions and safety warnings and ensure you have all tools, parts,
and equipment necessary for a safe installation.
Care & Maintenance
* To keep the product clean & shining, follow the steps below:
1. Rinse with clean water & dry with a soft cloth
2. Do not clean with soaps, acid, polish, abrasives or harsh cleaners
3. Do not use cloth with a coarse surface
4. Unscrew the aerator and clean when necessary
* This installation manual is subject to change without further notice.
ACID

A. FaucetBody C. 6mm HexWrench
D. 2.5mm Hex Wrench
A
3
Diagram and Parts List
B. Easy Install Assembly
B
C
D

Faucet Dimension
Installer Tip:
3/8”-compression
12 1/4''
[312.2mm]
4 1/4''
[109.1mm]
Max: 2 3/8''
[61.0mm]
7''
[178.7mm]
5 1/2''
[140.8mm]
7 1/4''
[184.9mm]
2''
[52.0mm]
4

5
Step 1: Installing the easy install assembly
Remove the old
faucet. Clean the mounting surface. Check
for the properthickness of the sink.
Insert the base (a) into sink.
a
b
NOTE: “Front” on the base (a) mustface the
front of the sink. The twomounting plates(b)
on the base (a) mustbe loose and movable
during the installation of the base (a).
Step 2: Installing the easy install assembly
Fig 1 Fig 2
Press the base (a) so that it can not move, then turn the screw with the provided
hex wrench (C, HEX: 6.0mm) clockwise, as shown Fig 1. When the mounting
plates (b) make contact with the sink (1), continue toturn the screw with the
provided hex wrench (C, HEX: 6.0mm) clockwise, as shown Fig 2, until the
base (a) is completely tightened and secured, as shown Fig.4.
Fig 3
Fig 4
C
a
b1
C
a
b
1
C
a
b
C
a
b
1
1

Step 3: Installing the faucet
Insert the supply lines (1) throughthe hole of the base (a). Carefully insert the
hoses into the base. Place the faucet assembly (A) onto the base (a) as shown in
with the provided hex wrench (D, Hex: 2.5 mm).
1
a
D
A
6

Step 4: Connect waterlines to main valve
Attach waterlines to angle stops
and tighten until snug. Turn on angle
stops and check for leaks (DONOT TURN
FAUCETON).
Step 5: Flush faucet
After installing faucet, remove aerator.
Turn water on for30 seconds to remove any
debris. Reassemble aerator. Donot lose the
gasket (1) in the aerator.
1
7
NOTE
are installed before connecting to
the main valve.

Replacement Parts
1. Aerator Assembly
Replacement Parts List Part #
2. Washer
3. Block
5. Index
6. Set Screw
7. Cartridge
9. Cap
10. Handle
11. Set screw
Finish / Color
KP27222
KP27033
KP27257
KP27258
KP27259
KP27260
KP27295
KP27031
KP27030
8. Bonnet Nut
4. O-ring KP27029
12. Cover Button
KP27001
KP27002
13. O-Ring Set of 2 KP27171
*Denotes faucet component color options:
SFS - Spot Free Stainless Steel;
CH - Polished Chrome;
GR - Grey; BL - Black;
MB - Matte Black;
BB - Brushed Brass;
SFACB - Spot Free Antique Champagne Bronze
CH, SFS, MB,
BB, SFACB*
14. Easy Install Assembly
15. Hex wrench
KP27262
16. Hex Wrench
KP27020
KP27263
17. Filter Washer KP27167
1
GR, BL*
GR, BL*
2
3
4
5
6
789
10
11
12
15
13
14
16
17
GR, BL*
CH, SFS, MB,
BB, SFACB*
CH, SFS, MB,
BB, SFACB*
8
11

Troubleshooting
If you have followed the instructions carefully and your faucet still does not work
properly, take the following coorective steps:
PROBLEM CAUS E A CTI O N
Leakage under the
handle
Bonnet nut (8) has
come loose
Remove the coverbutton (12).
Loosen set screw (11) with hex
wrench (15). Remove the
handle (10) and cap (9) . Tighten
bonnet nut (8) with an
adjustable wrench
The aerator has an
irregular or reduced
The aerator is dirty or Remove the aerator and
checkfor debris.
Ensure that the rubber
washer is properly installed.
completely
Cartridge may need to
be adjusted or replaced
Remove the coverbutton (12).
Loosen set screw (11) with hex
wrench (15). Remove the
handle (10) and cap (9).
Tighten bonnet nut (8) with an
adjustable wrench. Remove the
cartridge (7). Check forcracks
water. hose connectors is dirty. water valve and unscrew the
hose connectors from water
supply lines. Clean the
washer in the water lines with
hot water, removing any debris
or calcium build up
9