Kraus Cirrus FUS-13102 User manual

INSTALLATION MANUAL
Cirrus 4” Centerset Basin Faucet
FUS-13102
www.kraususa.com I toll free: 1.800.775.0703 I © 2014-2015 Kraus USA Inc.

Thank you for purchasing Kraus
We would like to take this opportunity to thank you for your business with Kraus
USA. It is our sincere hope that you are completely satised with your experience.
We welcome any questions or comments you may have, and will be glad to assist
you in the future.
For more information about Kraus products, please visit our website at:
www.kraususa.com
Please register your new Kraus product at the following web address in order to
activate the warranty and receive the full benet of customer support:
www.kraususa.com/registration
Sincerely,
Kraus Customer Service Department

Prior to Installation:
• Make sure you have all necessary parts by checking the diagram and parts list. If
any part is missing or damaged, please contact Kraus Customer Service at 800-
775-0703 for a replacement
• Turn o the hot and cold water supply at the angle stops and turn on the old
faucet to release any built up pressure. Remove existing faucet. Clean sink or
countertop to remove any debris, plumber’s putty, or silicone
• Place bucket under angle stops. Turn on to ush any debris prior to installing new
plumbing. Shut o angle stops
• Max countertop thickness: 1-3/8”
Tools you will need:
Adjustable Wrench Safety Goggles Bucket
Plumber’s Putty
6 5/8”
5 4/5”
3/8”
(10mm)
7/8”
19.7º(22mm)
8 5/16”
1 1/4-18UNF-2A
(21mm)
10 1/8”
(257mm)
1 3/8”
(35mm)
3 3/4”
(168mm)
(147.3mm)
(96mm)
∅ 1 3/4”
(
∅ 45mm)
∅ 1 15/16”
(
∅ 50mm)
9/16”-18UNEF
27mm ~ 41.3mm 1 1/16” ~ 1 5/8”
∅ 1 15/16”
(
∅ 50mm)
12 7/16”
(316mm)
1 5/8”
(42.5 mm Max)
7A
8B
8C
8D
8A
7A
8B
8C
8D
8A

FUS-13102 Diagram and Parts List
A
B
C
D1
D2
D3
A. Faucet Body
B. Putty Plate
C. Mounting Nut
D. Aerator Assembly
D1. Aerator Washer
D2. Aerator
D3. Aerator Cover

Faucet Dimensions

Lift Rod Drain Diagram and Parts List
a
b
c
d
e
f
g
ijkl m
n
o
p
h
a. Waste Stopper
b. Drain
c. Rubber Washer
d. Concave Washer
e. Plastic Washer
f. Mounting Nut
g. Tailpipe Washer
h. Tailpipe
i. Top Hat Washer
j. Drain Off Pole
k. Washer
l. Retaining Nut
m. Extender Rod
n. Clip
o. Thumb Screw
p. Lift Rod

Lift Rod Drain Dimensions
a
b
c
d
e
f
g
ijkl m
n
o
p
h

Step 1: Remove mounting hardware
Remove mounting nut (C) and
putty plate (B) from threaded
mounting pipe
Step 2: Install faucet
Apply a small amount of putty
to groove along bottom outer
edge of putty plate (B). Secure
putty plate to faucet. Install
faucet through holes in sink or
countertop
AA
B B
C
C
C
C
Plumbers Putty
D1
D2
D3
AA
B B
C
C
C
C
Plumbers Putty
D1
D2
D3
Installer Tip: Make sure hole
on putty plate (B) is positioned
to the rear of the faucet for the
lift rod to go through

Step 3: Secure faucet
Tighten mounting nuts (C) onto
threaded mounting pipe from
underneath the countertop or sink
(HAND-TIGHTEN ONLY)
Step 4: Connect waterlines to main valve
Thread hot & cold waterlines (not
included with faucet) to threaded
mounting pipe. (A. Hot Side: Left
B. Cold Side: Right). Secure other
end of waterlines to angle stops.
Tighten both ends with adjustable
wrench until snug. Turn on angle
stops and check for leaks (DO NOT
TURN ON FAUCET)
AA
B B
C
C
C
C
Plumbers Putty
D1
D2
D3
AA
B B
C
C
C
C
Plumbers Putty
D1
D2
D3
Installer Tip:
Recommended waterlines:
3/8 in. OD x 1/2 in. IPS

Step 5: Install Drain
a
b
c
d
e
f
g
poo
nn
m
l
p
m
d
g
b
h
a
b
b
c
e
f
h
ikl
o
p
H1
H2
H3
jklj
1
2
3
4
5
6
7
poo
n
j
hk
l
n
m
12
po
p
m
d
g
b
h
a
b
b
c
e
f
8
911 12
D1
D2
D3
j
1
2
3
4
5
6
7
poo
n
j
hk
l
n
m
12
po
p
m
d
g
b
h
a
b
b
c
e
f
8
911 12
D1
D2
D3
j
• Remove waste stopper (a) from
drain (b). Remove tail pipe (h),
mounting nut (f), plastic washer
(e), and concave washer (d) from
drain (b). Remove retaining nut
(l) and washer (k) from tailpipe
(h)
• Install drain (b), with rubber
washer (c) attached, into the drain
hole. Attach concave washer (d)
with narrow end up, plastic washer
(e), and mounting nut (f) to drain
(b) from underneath countertop or
sink. Secure tightly to sink with an
adjustable wrench
• Thread tailpipe (h) onto drain (b)
and hand-tighten. Adjust tailpipe
(h) so drain o pole opening is to
the rear of the sink
Installer tip: Leave top hat
washer (g) in tailpipe (h)
Installer Tip: Make sure
tailpipe washer (g) is installed
in tailpipe (h)