Kraus Oletto KPF-2821 User manual

Oletto™Single Handle Pull Down Kitchen Faucet
KPF-2820
KPF-2821
INSTALLATION GUIDE
www.kraususa.com I Toll Free: 1.800.775.0703 I © 2019 Kraus USA Inc. I REV. DEC 16, 2020

Congratulations on the purchase of your new
Please keep the box and packaging materials until your product is
completely installed. If you have any questions, require technical
assistance, or have any problems with your product:
Please contact our Customer Service Team
1-800-775-0703 / [e-mail]
Have the model number available, and retain a copy of your receipt
with purchase date for reference.
If for any reason this product does not meet your expectations,
please be sure to repack this product in the original box and
packaging material to avoid damage during transit.
DO NOT RETURN TO STORE
1

Prior to Installation:
•Make sure you have all necessary parts by checking the diagram and parts list. If
any part is missing or damaged, please contact Kraus Customer Service at 800-775-
0703 for a replacement
•
•Pre-drilled countertop hole size requirement: 1-3/8”(min)
•Max countertop thickness: 3”
Tools you will need:
13
Wrench Phillips Screwdriver Safety Goggles
Silicone Sealant
(optional)
Pipe Tape
2
Turn o the hot and cold water lines at the angle stops and turn on the old faucet
to release any built-up pressure

3
A. Faucet Body
C. Rubber Washer
D. Metal Washer
F. Screws
A
Diagram and Parts List
G. Weight
J
H. Weight Clip
B
B. Flange
E. Mounting Nut
C
D
E
F
G
H
I
I. Quick Connector
J. Hex Wrench

4
Faucet Dimension (For KPF-2821)
Installer Tip:
3/8” compression
Ø2 1/4"
[57.0mm]
10 7/8"
[275.0mm]
10 1/2"
[265.5mm]
20 3/8"
[517.6mm]
3"
[76.5mm]
3 1/2"
[90.1mm]
12 1/2"
[318.9mm]

5
Faucet Dimension (For KPF-2820)
Installer Tip:
3/8” compression
Ø2 1/4"
[57.0mm]
16 5/8"
[423.7mm]
3 1/2"
[90.1mm]
8 7/8"
[227.0mm]
10 5/8"
[270.7mm]
8 3/4"
[222.9mm]
3"
[76.5mm]

F
Step 1: Installing the faucet
Shut o the water supply. Place faucet (A)
through the hole in countertop.
Secure the faucet (A) to the countertop using
the rubber washer (C), metal washer (D) and
mounting nut (E) provided. Tighten screws (F).
Step 2: Securing the faucet assembly
Push the quick connector (I) rmly upward
and attach it to the receiving block (a). Pull
down moderately to ensure the connection
has been made.
6
C
D
F
A
E
a
I
(2N.m
Max)

Step 3: Securing the faucet assembly
Install the weight clip (H) at the point of
the hose marking "weight here". Insert
the weight (G) onto the weight clip (H)
by sliding it down onto the weight clip (H).
Step 4: Connect waterlines to main valve
7
Attach waterlines to angle stops
and tighten until snug. Turn on angles
stops and check for leaks (DO NOT TURN
FAUCET ON)
Weight
here
Weight
here
H
G

8
Step 5: Flush faucet
Pull the hose assembly out of the spout and
remove the spray head by unscrewing it from
the hose in a counterclockwise direction. Be
sure to hold the end of the hose down into
the sink and turn the faucet on to the warm
position where it mixes hot and cold water.
Flush the water lines for one minute. This
Fushesaway any debris that could cause
damage to internal parts. Check for leaks.
Re-tighten any connections if necessary, but
do not overtighten. Reinstall the spray head
by hand tightening it back onto the spray
hose.
After installation is completed, turn on the
hot and cold water supplies. Check for leaks.

9
Replacement Parts
1. Sprayer Head
Replacement Parts List Part #
2. Sprayer Washer
3. Sprayer Hose
5. Inverter
6. Cartridge
7. Bonnet Nut
9. Handle
10. Set Screw
11. Cover Botton
Finish / Color
KP27211
KP27069
KP27202
KP27203
KP27204
KP27001
KP27207
KP27208
KP27233
(For KPF-2821)
8. Cap & O-ring
4. O-ring KP27210
12. Flange & Washer
KP27002
21
SFS, MB,
SFACB, BB*
KP27205
GR, BL*
13. Block KP27073
*Denotes faucet component color options:
SFS - Spot Free Stainless Steel ; MB - Matte Black; SFACB - Spot Free Antique Champagne Bronze
GR - Grey; BL - Black; BB - Brushed Brass; Grey hose with Spot Free Stainless Steel (GRSFS);
Black hose with Matte Black (BLMB); Black hose with Brushed Brass (BLBB);
Black hose with Spot-Free Antique Champagne Bronze (BLSFACB)
SFS, MB,
SFACB, BB*
14. O-ring
15. Rubber & Metal Washer
KP27092
16. Mounting Nut & Screw
KP27028
KP27079
SFS, MB,
SFACB, BB*
17. Weight & Clip Assembly
18. Filter Washer
KP27212
19. 1.8GPM Flow Restrictor
KP27167
KP27074-WHWHITE
SFS, MB,
SFACB, BB*
1
678
9
10
11
12
13
14
15
16
17
19
20
2
3
4
5
18
20. Quick Connector
Assembly KP27090
21. Hex Wrench KP27020
GRSFS, BLMB,
BLSFACB, BLBB*
KP27209
(For KPF-2820)