Kraus Turino KFDW1-33 User manual

www.kraususa.com I Toll Free: 1.800.775.0703 I © 2021 Kraus USA Inc. I REV. June 15, 2021
Fireclay Dual Mount
Workstation Kitchen Sink
KFDW1-33
R
INSTALLATION MANUAL

Congratulations on the purchase of your new Kraus plumbing fixture!
Please keep the box and packaging materials until your product is completely installed. If you have
any questions, require technical assistance or have any problems with your product:
Please contact our Customer Service Team
1-800-775-0703 / [email protected]
Have the model number available and retain a copy of your receipt with purchase date for
reference.
If for any reason this product does not meet your expectations, please be sure to repack this
product in the original box and packaging material to avoid damage during transit.
DO NOT RETURN TO STORE
STOP
2

3
Prior to Installation:
·Inspect the sink prior to installation to make sure the sink has not been damaged
during shipping.
·Observe all plumbing and building codes according to your state requirements.
·Additional floor and wall preparation may be required to avoid damaging the sink.
·Make sure to purchase the correct cabinet for your kitchen sink. Base cabinets
should be 3" larger than the actual size of the sink.
·Not recommended to be installed with laminate countertop.
For technical assistance or replacement parts, please contact Kraus
Customer Service and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or [email protected]
The step-by-step guidelines in the installation instructions are a general reference for
installing a Kraus Sink. Should there be any discrepancies, Kraus cannot be held liable. It is
recommended to install all Kraus products by hiring a licensed professional.

Tools you will need:
4
NOTE: Specialized tools may be necessary to install Kraus Fireclay sinks with
countertop materials other than wood, marble or granite.
Phillips Screwdriver Pencil
Tape Measure Screwdriver Level
Safety Goggles Silicone Adhesive Jig Saw Acetone
Drill
Dimensions
KFDW1-33
33 1/8" x 19 1/2" x 10"
ACETONE
R 5/8"
(15mm)
33 1/8" (842mm)
30 1/2" (775.65mm)
19 1/2" (497mm)
17" (430.76mm)
15 3/4" (400.27mm)
4 3/8" (112mm)
3 1/2"
(90mm)
10"
(254mm)

5
Undermount Installation
1. Measure & Build Supports
·Build supports on inside of cabinet based on sink measurements
Installer Tip: Support options
·1 1/4" Angle Irons
·(2) 2" x 4'
·3/4" Plywood
NOTE: Due to the typical ±3mm side wall
variance in manufacturing, it is recommended
that you design / modify the sink cabinet to
match your clients individual sink(s) need.
SUPPORTS

6
2. Install Sink
·Place sink in opening. The weight of sink should be sustained
by the built supports.
·Make sure sink is leveled from front to back and side to side
·Make sure the top of the sink is flush with the top of the cabinet
·Uses silicone to fill in gaps where necessary

7
3. Cut Countertop
·Kraus recommends providing the cabinet maker with the actual sink to be installed prior
to the cabinet fabrication.
·It is recommended that the sink be installed with an approximately 1/8" positive reveal.
It is further recommended that the installer(s) discuss this with the customer and agree
that this finished appearance is the desired effect.

8
Installer Tip: Use acetone or denatured alcohol to remove any excess sealant.
4. Install Countertop
·Use a bead of silicone (or preferred adhesive) around the rim of the sink. Check the
alignment of the sink to the cutout in the countertop. Place countertop cutout hole over
sink and press firmly.
Silicone Adhesive

9
5. Installing Plumbing and Fixtures
·Connect drain, trap to drain and water supply connections to the faucet according to
manufacturer's instruction.
·Run water into sink and check for leaks.
·Note: Before installation, please check that the drain kit complies with ASME
A112.18.2/CSA B125.2 and with CUPC certification.

10
Top Mount Installation
1. Measure & Build Supports
·Build supports on inside of cabinet based on sink measurements
·The supports should be flush with the top of the cabinet
Installer Tip: Support options
·1 1/4" Angle Irons
·(2) 2" x 4'
·3/4" Plywood
NOTE: Due to the typical ±3mm side wall
variance in manufacturing, it is recommended
that you design / modify the sink cabinet to
match your clients individual sink(s) need.
SUPPORTS