Kraus Sellette KPF-1683SFS User manual

Sellette Single Handle
Commercial Style Pull-Down
Kitchen Faucet
KPF-1683
TM
www.kraususa.com I Toll Free: 1.800.775.0703 I © 2018 Kraus USA Inc. I REV. November 13, 2019
R
INSTALLATION MANUAL

Congratulations on the purchase of your new
Kraus plumbing fixture!
Please keep the box and packaging materials until your product is
completely installed. If you have any questions, require technical
assistance or have any problems with your product:
2
Please contact our Customer Service Team
1-800-775-0703 / [email protected]
Have the model number available and retain a copy of your
receipt with purchase date for reference.
If for any reason this product does not meet your expectations,
please be sure to repack this product in the original box and
packaging material to avoid damage during transit.
DO NOT RETURN TO STORE
STOP

Prior to Installation:
·Make sure you have all necessary parts by checking the diagram and
parts list. If any part is missing or damaged, please contact Kraus
Customer Service at 800-775-0703 for a replacement.
·Turn off the hot and cold water supply at the angle stops and turn on
the old faucet to release any built up pressure. Remove existing faucet.
Clean sink or countertop to remove any debris, plumber’s putty, or
silicone.
·Flush angle stops to release any debris prior to installation.
·Pre-drilled hole size requirement: 1 3/8" (min) - 1 1/2" (max)
·Max countertop thickness: 1 3/8”
·1, 2 or 3 hole installation
3
For technical assistance or replacement parts, please contact Kraus
Customer Service and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or [email protected]

44
Diagram and Parts List
1
2
8B
8A 9
3B
3A
4A
4C
4D
5
6
7
4B
10

55
Diagram and Parts List Tools you will need
1. Spray Head
2. Faucet Body
3. Deck Plate Assembly
A. Deck Plate
B. Base Plate
4. Mounting Hardware
A. Rubber Washer
B. Metal Washer
C. Mounting Nut
D. Mounting Screws
5. Spray Hose
6. Weight
7. Quick Connector
8. Hot and Cold Nylon Waterlines
A. Cold
B. Hot
9. Hex Wrench
10. Base O-Ring
Adjustable Wrench
Silicone Sealant
(optional)
Phillips Screwdriver
Safety Goggles

66
Installer Tip:
Shut off main water supply before installing new faucet.
Faucet Installation Procedure
8 5/8" (220mm)
7" (178mm)
23 1/4" (589mm)
5 1/8" (130mm)
8 3/4" (223mm)
3 1/2"
(90mm)
11 1/2" (292mm)
10 1/2" (266mm)
2-M10

7
Step 1A. Faucet installation - with deck plate
Step 1B. Faucet installation - without deck plate
For three-hole installation:
Deck plate (3A), base plate
(3B), and silicone sealant
(optional) are required.
For single-hole installation:
Deck plate (3A), base plate
(3B) and silicone sealant
are NOT required.
3A
3B

8
Step 2. Install faucet and mounting hardware
Step 3. Secure mounting hardware
Insert faucet body (2) into
hole in countertop or deck
plate assembly (3). Install
mounting hardware (4A, B, C & D)
from underneath the
countertop.
Adjust direction of faucet
body (2) so that handle is on
right side of faucet. Tighten
mounting nut (4C) until snug.
Tighten mounting screws
(4D) to nut with a Phillips
screwdriver until snug.
4A
4C
4D
4C
4D
4B

9
Step 4. Attach spray hose and counterweight
Step 5. Connect waterlines
Connect spray hose (5)
to quick connector (7)
attached to supply line.
Install weight (6) on lowest
vertical point on spray
hose (5).
Connect waterlines (8) to angle
stops. Tighten both ends of
waterlines with a wrench
until snug. Turn on hot and
cold angle stops and check
for leaks.
7
5
6
8
NOTE: Make sure filter
washers are installed.

10
Step 6. Flush spray hose
Remove spray head (1) from
spray hose (5). Hold tip of
spray hose (5). Turn faucet on
and let the water run for 60
seconds to flush any debris.
Step 7. Check for leaks
Check for leaks at the
connections. Retighten if
necessary.
NOTE: Please make sure washer is
installed attaching spray head to hose.
5
1