Krausen 800 WHITE User manual

1
Installation and User Manual/Warranty
ONLINE Drinking Water System
Model Numbers：KRAUSEN 8 00 WHITE
KRAUSEN 8 00 ADVANCE
KRAUSEN 8 00 EVOLUTION
Dear customer,
Thank you for purchasing KRAUSEN water purifier!
You now have water treatment equipment that is at the world’s leading position in today’s water
treatment field. It produces pure water that can be consumed directly so the water you drink is cleaner and
also beneficial to your health.
Before you install and use this water purifier, please be sure to read the user manual, this enables
qualified and standardized installation as well as reasonable use and maintenance to maximize the
effectiveness of your water purifier.
If you experience difficulties during installation or usage, please contact your local distributor to carry
out repairs or maintenance for you.

2
Contents Page
Safety Considerations…………………………………………………3
Product Introduction……………………………………………………4
Installation Method……………………………………………..………7
◆Pre-Installation Preparations………………………………………..…… 7
◆Instructions for Proper Installation……………………………….……… 7
◆Installation Notes……………………………………………...…..……… 9
Adjustment Methods………………………………………...…………9
Usage Methods…………………………………………………………9
Maintenance and Upkeep……………………………………..………10
◆Computer board control………………………………………………10
◆Filter Replacement Time……………………………….…………………10
◆Filter Replacement Method……………………………….………………11
◆Notes ……………………………………………………………….………11
Failure Diagnosis and Resolution……………………….……………11
After-Sales Service……………………………………..………………12
Packing List………………………………………………………………12

3
Safety Considerations(Be sure to read and remember these safety considerations）
In order to avoid property damage and harm to you and others, make note of the following safety
precautions.
★Ignoring the following safety precautions could result in a risky situation:
Warnings If you ignore contents in this section, it may cause permanent damage to the
water purifier or cause serious property damage.
Notes If you ignore the contents in this section, it may lead to damage of some parts of the
water purifier or may result in some property damage.
Warnings
Do not disassemble or modify this
water purifier on your own!
Unauthorized disassembly
or modification of the machine
could lead to machine
malfunctions or leakage
accidents. Please check with
the store where you purchased
this product for product
consultation in order to arrange for repairs.
Do not put things on the top of the
machine!
Obstructing the heat dissipation
may lead to machine damage or
fires.
Do not put heavy things on the
machine!
if you put heavy things on
the machine, it may damage
the spare parts inside, cause
the leakage, malfunction even
serious property damage..
Do not use this water purifier under high
water pressure conditions!
Operating under high-
pressure conditions may cause
the water purifier pipes to
rupture, resulting in leakage, the
machine working improperly, or
even serious property damage.
Recommended inlet pressure is
0.05MPa to 0.35MPa.
Do not let the machine come in contact
with corrosive materials!
These materials could
corrode the outer cover and
affect the water parts or some
toxic and hazardous
compounds could penetrate
the water purifier pipes,
leading to contaminated water
production and machine leakage, which could even
cause bodily and property damage.
Do not put the water purifier close to the
fire!
Do not put the water purifier
near a fire source or place
where the temperature is too
high, this may cause
deformation or melting of the
machine, causing damage or
leakage, which could lead to
serious bodily and property damage.

4
Notes
Do not use the water purifier when the
sewer is blocked up!
If it is used while
the sewer is blocked, it may
cause the waste water to
back up or pollution to get
inside the water purifier.
The waste water discharge pipe and
wastewater ratio device cannot be
blocked!
When the waste water
discharge pipes and waste water
ratio device are clogged, it may
lead to high TDS effluent, the RO
membrane may get blocked or
the water purifier may not work.
Water purifier inlet water temperature
should not exceed 38℃!
If the inlet water
temperature is over 38℃, it
will damage the reverse
osmosis membrane leading
to membrane failure.
Do not use in conditions under 5℃!
If the temperature in the room is below 5℃, please be
sure to take measures
to prevent freezing, such
as starting the heater or air
conditioner to prevent leakage
or cracked pipes caused from
water freezing inside the machine.
Do not use this water purifier outdoors!
If this water purifier is used
outdoors, it can lead
to accelerated aging of the
water purifier pipes and
parts, which can cause
leaking or machine failure.
Do not use the water purifier in direct
sunlight!
When the water purifier is in
sunlight for a period of time, it
may create a breeding ground
for microorganisms so the water
purifier water quality will
decrease, and they may pollute
the internal components of the water purifier.

5
Product Introduction
1. Blown-up profile of the water purifier
1（a）
1（b）

6
2. Electrical diagram
Diagram 2
3. Water route map
Diagram 3

7
4. Technical Parameters
Voltage
AC 220V 50HZ
Power Rating
75W
Suitable Water Pressure
0.05MPa～0.35MPa
Operating Pressure
≤0.85MPa
Inlet Temperature
5-38℃
Maximum Inlet Water TDS Value
≤1000PPM
Maximum Daily Water Production Volume
800
Gallons, approximately
2880 Liters
Electric Shock Protection Type
Type II
Suitable Water Quality
Municipal tap water meeting the
GB5749-2006 standards
Note: Due to product improvements, the above parameters may change but the product name plate shall
stay the same. TDS refers to the influent total dissolved solids.
5. Water Purifier Main Parts Function Introduction
Using the current most advanced international RO technology, standard configuration is as follows:
①First is a Inline 2.5`` 5-micron PP filter:
The aperture of the PP filter is 5 microns, can effectively filter rust, sand, other larger particles and solid
impurities in water.
②Second is a Inline 2.5`` granular activated carbon filter:
Can effectively adsorb chlorine, humus, disinfection by-products, odors, colors, and other materials.
③Third is Inline 2.5`` 1-micron PP filter:
Can further remove small particles in the water, suspended solids, colloids, etc.
④Fourth stage is x 2 RO membr sane :
Aperture is 0.0001 micron (0.1 nm), reduces bacterium by 4,000 fold, reduces viruses by over 200 fold,
so you can effectively remove bacteria, viruses, heavy metals, pesticide residues, and other harmful
substances from the water.
⑤The fifth-stage is a post-activated carbon filter:
Regulates water taste, keeps water fresh.
Note: This machine also has an optional configuration:
Pretreatment Filter: KDF two stage filter, KDF three stage filter
Post-filter: Alkaline filter, infrared mineralization activated carbon filter, alkaline sterilization filter,
sterilizing filter

8
6. Water Purifier Accessory Functions
High Pressure Pump: Boosts pressure to create a stable environment for the RO membrane.
Low Voltage Switch: To prevent pump idling. When the inlet water pressure is less than 0.03 MPa
or when the inlet water stops, the low-voltage switch automatically shuts off
the power source so the machine stops.
High-Voltage Switch: Prevents pump from fully turning. When the pressure tank is full or has
reached the set pressure, power supply is automatically cut off to stop the
machine.
Inlet Water Solenoid Valve: Connects or cuts off incoming water. Operating pressure range is less than
0.6MPa.
Non Return Valve: controls the flow direction.
Flow restrictor: control the ratio of pure and waste water
7. Direct flow purifier features:
1. Design without storage tank: New advanced design. The water flow is equal to the normal one with
tank. The user can get the pure water at the same time the machine is producing water. This design
solves the contamination problem (such as odors, bacteria etc) caused by long time pure water storage
in tank. It supplies the real “pure and fresh water”.
2. Large Production Capacity and Big Water Flow: Use a 24 x 00G RO membra sne . The production
capacity is 15 16- times of the standard 50G one, and is equal to the water flow of 50G model with
tank. It can reach 1 5. L/min 2～.0L/min
3. Suitable for low water pressure: It can start working if the feed water pressure is no less than
0.03Mpa.
4. Digital Computer Box Automatic Control System: The system can automatically control the water
auto flush process for the RO water purifier to ensure more reliable and safe operation of this machine;
5. Indicator light Display: Indicator light show the working status, it is easy for the maintenance.
6.The inlet and outlet water is on the side: easy for the machine’s installation.
7.Quick connector: New advanced design, quick connectors make it easy for installation, usage
and maintenance.
8.Inline filter, easily dismantle: only dismantle the inline filter to make easily changing

9
Installation Method
This company recommends that professionals install the machine for you, because you must use drills and
other power tools in the installation process. If you are installing it yourself, please refer to the following
steps and diagrams:
1. Pre-Installation Preparations
①Confirm the location the water purifier will be installed (when installing, it should depend on the actual
circumstances)
②Confirm the various tools required for installation
Adjustable spanner
1
Drill
1
6.2mm drill bit
1 (waste water hole)
Hole saw, φ14mm
1 (high-speed steel or marble hole saw)
Phillips and flathead screwdrivers
1 of each
Scissors
1 pair
18-21mm wrench
1
14-16mm wrench
1
Needle nose pliers
1
③Confirm that you have all the connectivity accessories required for installation
④Prior to installation turn off the water and/or electricity
2. Instructions for Proper Installation
①Inlet water metal hose and 3-way inlet water joint installation method (if the metal hose diameter is
3/8’’ the 3-way inlet water joint must be purchased separately)
First close the inlet water valve. Unscrew from the metal hose. Remove the 3-way inlet water
joint from the water purifier accessories box, thread one end of the inlet water 3-way joint into the
inlet water valve outlet; one end of the newly unscrewed metal hose should be screwed into the
3-way inlet water joint screw nut (See Diagram 4).

10
Diagram 3
②3-way inlet water joint and inlet water ball valve installation method
Take out the inlet water ball valve from the water purifier accessories box, wrap one end of the ball
valve external threads with the appropriate Teflon tape (See Diagram 5), if you have silica gel,
spread a little on and then screw the ball valve into the corresponding hole of the 3-way inlet water
joint (See Diagram 6). Take out the Ø9mm water pipe from the accessories box, using scissors
cut a suitable length of pipe, connect one end of the pipe with the inlet water ball valve (See
Diagram 4), finally screw the nut in place.
Diagram 5 Diagram 6
③Gooseneck faucet installation
In the counter where the faucet is to be installed drill a φ14mm hole in an appropriate position, then
take out the faucet from the water purifier accessory box. Start the faucet installation: first put the
stainless steel neck on the faucet main body (See Diagram 7), then lower the main part of the
faucet into the already drilled hole, and then put the spacer on the lower part of the faucet. Screw
the fixed nut into the bottom end of the faucet to fix the faucet to the counter, finally put the