Krausen NEW LINE Series User manual

Installation and User Manual
Models: KRAUSEN NEW LINE A-D LCD
For indoor use only
Dear customer,
Thank you for purchasing our company’s water purifier!
You now have water treatment equipment that is at the world’s leading position in today’s water
treatment field. It produces pure water that can e consumed directly so the water you drink is cleaner and
also eneficial to your health.
Before you install and use this water purifier, please e sure to read the user manual, this ena les
qualified and standardised installation as well as reasona le use and maintenance to maximise the
effectiveness of your water purifier.
If you experience difficulties during installation or usage, please contact your local distri utor to carry
out repairs or maintenance for you.
-1-

Contents _____________ Page
Safety Considerations…………….....………..……………………………3
Product Introduction……………………….......…...………………………6
Installation Method……………………………........……………..………12
1. Pre-Installation Preparations………………………….......…………....…… 12
2. Instructions for Proper Installation………………………….......……...…… 13
3. Installation Notes……………………………………………...….......……… 13
Testing Methods..................................................................................16
Usage Methods………………………………………………………....…17
Maintenance and Upkeep……………………………………..……....…17
1. Filter Replacement Time……………………………….…………………......17
2. Filter Replacement Method…...………………………….………......………18
3. Notes ……………………………………………………………….…….....…18
Failure Diagnosis and Resolution……………………….…………....…19
After-Sales Service……………………………………..…...………...….19
Packing List…………………………………………………....………..…20
-2-

Safet Considerations (Be sure to read and remem er these safety considerations）
In order to avoid property damage and harm to you and others, make note of the following safety
precautions.
Ignoring the following safet precautions could result in a risk situation:★
Warnings If you ignore contents in this section, it may cause permanent damage to the
water purifier or cause serious property damage.
Notes If you ignore the contents in this section, it may lead to damage of some parts of the
water purifier or may result in some property damage.
Warnings
Do not disassemble or modif this
water purifier on our own!
Unauthorised disassem ly or
modification of the machine
could lead to machine
malfunctions or leakage
accidents.
Please check with the store where you purchased
this product for product consultation in order to
arrange for repairs.
Do not put things on the top of the
machine!
O structing the heat dissipation
may lead to machine damage or
fires.
Do not put heav objects on the water
purifier!
If heavy o jects are placed on
the water purifier, it may result in
damage to the water purifier’s
dust cover or internal
components, which could lead to
leakage, the machine working
improperly, or even serious
property damage.
Do not use this water purifier under high
water pressure conditions!
Operating under high pressure
conditions may cause the water
purifier pipes to rupture, resulting in
leakage, the machine working
improperly, or even serious
property damage. Recommended
inlet pressure is 0.1MPa to 0.35MPa.
Do not let the machine come in contact
with corrosive materials!
These materials could corrode
the outer cover and affect the
water parts or some toxic and
hazardous compounds could
penetrate the water purifier
pipes, leading to contaminated water production
and machine leakage, which could even cause
odily and property damage.
Do not put the water purifier close to the
fire!
Do not put the water purifier near a
fire source or place where the
temperature is too high, this may
cause deformation or melting of the
machine, causing damage or
leakage, which could lead to serious odily and
property damage.
-3-

Do not use a power source exceeding
the machine’s specified value, onl use
220V AC power!
The outlet used for the machine’s
current must e greater than the
machine’s specified value;
otherwise it may lead to
overheating or fire.
When installing or repairing, the machine
must be disconnected from the power
source!
Otherwise it may lead to electric
shock.
Do not damage the power cord or
outlet!
Doing so may lead to electric
shock, short circuiting, or fire.
Do not touch the power plug with wet
hands!
It may lead to electric shock.
Notes
-4-
Do not use the water
purifier when the sewer is blocked up!
If it is used while the sewer is
locked, it may cause the
waste water to ack up or
pollution to get inside the
water purifier.
The waste water discharge
pipe and waste water ratio device cannot
be blocked!
When the waste water discharge pipes and waste
water ratio device are clogged, it may lead to high TDS
effluent, the RO mem rane may get locked or the
water purifier may not work.
Water purifier inlet
water temperature should not exceed
38 !℃
If the inlet water temperature is over 38 , it will℃
damage the reverse osmosis mem rane leading to
mem rane failure.
Do not use in conditions under 5 !℃
If the temperature in the room is elow 5 , please e℃
sure to take measures to prevent freezing, such as
starting the heater or air conditioner to prevent leakage
or cracked pipes caused from water freezing inside the
machine.
Do not use this water purifier outdoors!
If this water purifier is used
outdoors, it can lead to
accelerated aging of the water
purifier pipes and parts, which
can cause leaking or machine
failure.
Do not use the water
purifier in direct sunlight!
When the water purifier is in
sunlight for a period of time, it may
create a reeding ground for
microorganisms so the water
purifier water quality will decrease,
and they may pollute the internal
components of the water purifier.

The installer, service man, user or other responsible person should control system pump's
pressure, volume of the waste water and filter's life for replacement.
The pump type should correspond to the system model. Otherwise, it's can destroy the
pump or other system's part.
Unauthorised disassembly or modification of the machine could lead to machine
malfunctions and leakage accidents.
For example, the system's pump type D” cannot be installed on the system model A”, B”
or C”.
In this case, the manufacturer doesn't bear responsibility for system operation.
The working pressure optimal parameter of the system's pump on the membrane must be between
5,0 – 7,0 bar.
Notes Due to product improvements, the parameters may change, but the product name
plate can stay the same.
-5-

Product Introduction
1. Blown-up profile of the water purifier
The system could e in 2 versions ased on normal racket or sta le racket.
Normal Bracket Stable Bracket with Pressure meter
Diagram 1
2. Electrical diagram
Diagram 2
-6-

3. Water route map
Diagram 3
4. Technical Parameters
4.1 KRAUSEN NEW LINE A – D
All types of NEW Line series (A-D) must be used only for domestic consumption, as a systems of
direct filtration without additional tank usage and the drinking water production should not exceed
100 liters per day.
Model
NAME
NEW
LINE A
NEW
LINE A++
NEW
LINE B
NEW
LINE B++
NEW
LINE C
NEW
LINE C++
NEW
LINE D
NEW
LINE D++
Voltage AC 220-
240 V
50HZ,
24V, 1.8A
AC 220-
240 V
50HZ,
24V, 2.2A
AC 220-
240 V
50HZ,
36V, 1.5A
AC 220-
240 V
50HZ,
36V, 1.5A
AC 220-
240 V
50HZ,
36V, 2.8A
AC 220-
240 V
50HZ,
36V, 2.8A
AC 220-
240 V
50HZ,
36V, 3.2A
AC 220-
240 V
50HZ,
36V, 3.2A
Power
Rating
43 W 53 W 55 W 55 W 100 W 100 W 115 W 115 W
Suita le
Inlet Water 0.5 ～3.5 0.5 ～3.5 0.5 ～3.5 0.5 ～3.5 0.5 ～3.5 0.5 ～3.5 0.5 ～3.5 0.5 ～3.5
-7-

Pressure,
ar
Working
pump
pressure ,
ar
5.0 ～7.0 5.0 ～7.0 5.0 ～7.0 5.0 ～7.0 5.0 ～7.0 5.0 ～7.0 5.0 ～7.0 5.0 ～7.0
Pump New
Line type
A A++ B B C C D D
Inlet
Temperatur
e, ℃
5 - 38 ℃5 - 38 ℃5 - 38 ℃5 - 38 ℃5 - 38 ℃5 - 38 ℃5 - 38 ℃5 - 38 ℃
Maximum
Inlet Water
TDS Value,
ppm
≤1000 ≤1000 ≤1000 ≤1000 ≤1000 ≤1000 ≤1000 ≤1000
Drinking
Water
Production
Volume, ml/
1000 1500 1400 2300 2800 3200 3700 4100
Waste
Water
Production
Volume,
ml/min
600
ml/min
600
ml/min
1100
ml/min
700
ml/min
1100
ml/min
700
ml/min
1100
ml/min
600
ml/min
Electric
Shock
Protection
Type
Type II Type II Type II Type II Type II Type II Type II Type II
Hardness
level, max
mg-ekv/lit
8 8 8 8 8 8 8 8
MAX pure
water flow
per day (Lit)
40 40 40 40 80 80 120-140 120-140
Notes
Due to product improvements, the above parameters may change, but the product name plate can
stay the same. The parameters of drinking water/waste water volumes may vary depending of the
different factors such as membrane's quantity, membrane's type, temperature of the water,
temperature of the room, water quality, pressure of the pump, membrane capacity and etc.
The hardness could reduce membranes' life. In case, of the big hardness level, we recommend to
use prefiltration filters, such as Krausen water softeners systems or Krausen Aqua Mix Ion
systems, as well as to use antiscalant liquid for the special membranes for High TDS.
-8-

5. Water Purifier Main Parts Function Introduction
Using the current most advanced international RO technology, standard configuration is as follows:
①First is a 10-inch 5-micron PP filter:
The aperture of the PP filter is 5 microns, can effectively filter rust, sand, other larger particles and solid
impurities in water.
②Second is a 10-inch car on lock CTO filter:
Can effectively adsor chlorine, humus, disinfection y-products, odours, colours, and other materials.
③Third is a 10-inch 1-micron PP filter:
Can further remove small particles in the water, suspended solids, colloids, etc.
④Fourth stage is two RO mem ranes filters:
Mem rane can effectively remove acteria, viruses, heavy metals, pesticide residues, and other
harmful su stances from the water.
In case of 2, 3 pieces of mem ranes, the first mem rane capacity should e the iggest one, second
smaller and the final the smallest one. As an example, first mem rane is - 200 gallons and the second -
is 180 gallons for the system New Line A 380.
⑤The fifth-stage is a coconut activated post car on filter:
Regulates water taste, keeps water fresh.
6. Water Purifier Accessor Functions
High Pressure Pump: Boosts pressure to create a sta le environment for the RO mem rane.
Flow Restrictor: Waste Water Ratio Device, controls waste water flow.
Low Voltage Switch: To prevent pump idling. When the inlet water pressure is less than 0.03 MPa
or when the inlet water stops, the low-voltage switch automatically shuts off
the power source so the machine stops.
High-Voltage Switch: Prevents pump from fully turning. When the goose neck faucet closed and the
pressure reached the set pressure, power supply automatically cut off to stop
the machine.
Inlet Water Solenoid Valve: Connects or cuts off incoming water. Operating pressure range is less than
≤0.6MPa.
Non Return Valve: Also known as a one-way valve, controls the flow direction.
Flush Solenoid Valve: It's optional part and using for the modification KRAUSEN NEW LINE LCD
only. It's help to clean up 2 mem ranes surface, to prevent the rise of the
acteria, to extend the life of the mem ranes. The valve works automatically.
LED / LCD Controller It's optional computer controller, which operate all functions of the water purifier,
as well as mem ranes automatic cleaning.
LEKAGE SENSOR There is leakage protection function on the machine.
Water Purifier modification KRAUSEN NEW LINE LCD with LCD controller.
The LCD led controller works fully automatically. It help to clean up the mem rane surface, prevent the rise
of the acteria and extend the life of the mem rane. The signs of the display show the system's work:
-9-

LEAKAGE SENSOR TDS SENSORs
the light is on, when the mem rane flashing process started. The automatic
mem rane cleaning can e done every 7-8 hours or after immediately after
long work period of time. The limit time of flashing could e etween 0,5 – 1,5
min.
the light is on, when the drinking goose neck faucet closed.
The light is on when the machine purify the water.
The light is on, when the inlet water pressure is enough.
The light is on, when something wrong and need to repair.
The light is on, when the machine has leaking
-10-

Filter ser ice life
LCD display show the INLET water TDS
LCD display show the PURE water TDS
The “Strong washing” utton is a manual flashing start. It could pushed manually if need to make a
mem rane cleaning.
Control Function
Flush Function
1. When power on, the LCD display will all light, the uzzer will eep one time. Machine will flush
mem rane 90 seconds.
2. Click flush key in purify state, machine will flush mem rane 90 seconds.
3. Exit from source state, machine will flush mem rane 30 seconds.
4. Purify 2 hours accumulatively, machine will flush mem rane 30 seconds.
The pump and inlet solenoid and flush-solenoid are all on.
Source Function
7. If the low pressure switch is open more than 60 seconds continuously, Machine will in source state.
8. If the low pressure switch is close, machine will flush mem rane 30 seconds.
The pump and inlet solenoid and flush solenoid are all off. The uzzer will eep 10 times.
Full Function
1. If the high-pressure switch is open and the machine purify water more than 10 minutes, the machine
will flush mem rane 5 seconds. ( Pump and inlet solenoid and flush solenoid are all on) If the
machine purify water less than 10 minutes, flush solenoid will power on 10 seconds.
The pump and inlet solenoid and flush-solenoid are all off.
Purify Function
3. If the high-pressure switch is close, the machine will in purify state;
The pump and inlet solenoid are on, flush-solenoid is off.
Repair Function
2. If the machine purify water more than 6 hours continuously, and there is no full of tank, the machine
will e in repair state.
The pump and inlet solenoid and flush solenoid are all off. The uzzer will eep.
Leakage Function
If the leakage sensor detect water-leakage more than 5 seconds, the machine will e in leakage
state.
-11-

The pump and inlet solenoid and flush solenoid are all off. The uzzer will eep.
TDS Function
TDS is a measure of the combined total dissolved solids in a liquid.
The 3 small signs in left will show the original water TDS value; ( Measuring range 0-999)
The 2 ig signs in right will show the pure water TDS value; ( Measuring range 0-199)
Filter Life Replacement Reminder
The 5 timers accumulate water purify time.
Wires
No. Color Peripheral No. Color Peripheral
1 Yellow Low pressure Switch 7 Yellow Low pressure switch
2 Blue High pressure Switch 8 Green Pump
3 Blue High pressure Switch 9 Black Inlet valve
4 Red Flush valve 10 Red Flush valve
5 Green Pump 11 White 24Vdc
6 Black Inlet valve 12 Pink 24Vdc
7. Water purifier features:
①Design without storage tank: The water flow is equal to the normal one with tank. The user can get
the pure water at the same time the machine is producing water. This design solves the contamination
pro lem (such as odours, acteria etc.) caused y long time pure water storage in tank. It supplies the
real “pure and fresh water”;
②Large Production Capacit and Big Water Flow: The production capacity is 8 times of the standard
50G one;
③Quick-fitting Connector ：With newly designed quick-fitting connector on input and output water
side，install and uninstall easily.
Installation Method
This company recommends that professionals service man installs the machine for you, ecause you must
use drills and other power tools in the installation process. If you are installing it yourself, please refer to the
following steps and diagrams:
1. Pre-Installation Preparations
① Confirm the location the water purifier will e installed (when installing, it should depend on the actual
circumstances)
② Confirm the various tools required for installation
Adjusta le spanner 1
Drill 1
Hole saw, φ18mm, φ12mm, φ6mm 1 (high-speed steel or mar le hole saw)
Phillips and flathead screwdrivers 1 of each
-12-

Scissors 1 pair
21mm wrench 1
16mm wrench 1
14mm and 12mm multi wrench 1
Needle nose pliers 1
③ Confirm that you have all the connectivity accessories required for installation
④Prior to installation turn off the water and/or electricity
2. Instructions for Proper Installation
① Inlet water metal hose and 3-way inlet water joint
installation method (if the metal hose diameter is
9mm the 3-way inlet water joint must e purchased
separately)
First close the inlet water valve. Unscrew from the
metal hose. Remove the 3-way inlet water joint from
the water purifier accessories ox, thread one end of
the inlet water 3-way joint into the inlet water valve
outlet; one end of the newly unscrewed metal hose
should e screwed into the 3-way inlet water joint
screw nut (See Diagram 4).
Diagram 4
② 3-way inlet water joint and inlet water all valve installation method
Take out the inlet water all valve from the water purifier accessories ox, wrap one end of the all valve
external threads with the appropriate Teflon tape (See Diagram 5), if you have silica gel, spread a little
on and then screw the all valve into the corresponding hole of the 3-way inlet water joint (See Diagram
6). Take out the Ø 6mm water pipe from the accessories ox, using scissors cut a suita le length of
pipe, connect one end of the pipe with the inlet water all valve (See Diagram 4), finally screw the nut in
place.
Diagram 5 Diagram 6
③ Goosneck faucet installation
In the counter where the faucet is to e installed drill a φ12mm hole in an appropriate position, then take
out the faucet from the water purifier accessory ox. Start the faucet installation: first put the stainless
steel neck on the faucet main ody (See Diagram 7), then lower the main part of the faucet into the
already drilled hole, and then put the spacer on the lower part of the faucet. Screw the fixed nut into the
ottom end of the faucet to fix the faucet to the counter, finally put the appropriate length of 6mm pipe
into the water inlet connection, put the 6mm pipe stopper into one end, put on the 6mm nut, screw to the
-13-

ottom of the faucet (see Diagram 7). If you want to fix the faucet to the wall, please use the faucet
hanging piece. (when installing e sure to tighten the joints to prevent leakage)
Diagram 7 Diagram 8
④ Waste water pipe installation
Using a φ6mm drill punch a small hole into the sink drain pipe, take a suita le length of the 6mm water
pipe, lay one end just inside the hole (See Diagram 8), put some silica gel where the 6mm pipe and the
drain pipe connect to prevent leakage, use a ca le tie to fix the waste water pipe to the drain pipe. (for
large flow water purifiers you need waste water clip inserted into the already drilled drain pipe hole)
⑤ RO Mem rane Installation
First take the water purifier out from the packaging, find first mem rane shell (housing), which is after
the pump, unscrew the mem rane shell cover inlet water connection end, take out the inlet water pipe,
then use the mem rane shell wrench to unscrew the mem rane shell cover. Take the first RO
mem rane from its packaging, put the end of the mem rane with the O-ring into the reverse osmosis
mem rane shell (See Diagram 9) and push it in, finally screw the mem rane shell cover ack on, and
use the mem rane shell wrench to tighten the mem rane shell cover, put the inlet water pipe into the
mem rane shell inlet water connector and fix it, then put the mem rane shell card into clips. Secondly,
take the second mem rane shell and make all operation as a ove with first shell. Finally, carefully
recheck all connections of the water purifier.
Mem ranes shells usually marked y the num ers. The shell with num er 1 is for the mem rane with
higher gallon capacity, the num er 2 – for mem rane with lower gallon capacity.
ATTENTION!!! Please noted, that the normal pressure on the mem rane should have the range
etween 5,0-7,0 Bar, if the pressure igger then this num ers, please, use the flow restrictor for
decreasing the water pressure. If the pressure on the mem rane is higher than 7,0 ar, please, use the
smaller nominal of the restrictor or use adjusta le restrictor to decrease the the pressure to the
recommended parameters/
-14-

Warning:
◆ When installing the RO mem ranes, you should pay attention to the direction of the mem rane;
◆When installing the RO mem ranes, you should first make sure that one end of the mem rane
has an O-ring;
◆When installing, e sure to put the end with the O-ring into the end of the mem rane shell with the
pure water connection, when installing correctly you only need a little force to put the reverse
osmosis mem rane into the mem rane shell, if you encounter too much resistance, please do not
force the reverse osmosis mem rane into the mem rane shell, doing so may cause permanent
damage to the mem rane shell or mem rane components (the mem rane manufacturer does not
assume responsi ility for returned components due to damage during installation);
◆Damage to the mem rane shell and reverse osmosis mem rane element caused as a result of
the a ove reasons is not covered under the water purifier warranty.
Diagram 9
⑥ Installation of pretreatment filter cartridge
Take the filter cartridge out from package, tear the packing film and put into the filter housing y sequence , from right to
left： first put 5 micron PP filters; The second put activated car on filter,（ru er gasket side direction up；
The third put1 micron pp filters（diagram 10）
Diagram 10
3. Installation Notes
1 When installing the water pipes, cannot install a drain stopper, in addition, for the water pipe ottom
connector, the screw nut should have no wire teeth exposed.
-15-

2 If the inlet water pipe is 6mm, should ensure that the inlet water tu e and connector have 30-40cm
of straight piping to avoid urst pipe accidents caused y ending in the pipe.
3 If the power cord wiring needs to e longer, then according to the wiring requirements use a Φ8mm
pinched tu e to wrap around the connection, then on the outside wrap around insulating electrical
tape, do not place it on the floor, it should e suspended in the air or in another place away from the
ground.
4 When installing, if you need to make a hole in the wall, you should first make sure that there are no
electricity or water lines in the location you plan to drill.
5！The machine must e connected with the switch with relia le grounding line , otherwise
manufacturers are not responsi le for safety accidents caused.
6！The switch power supply must switching power supply must put in ventilated and waterproof
place， and keep adequate distance with machine, in avoid of accidents caused y water input.
Testing Methods
After confirming that the water route connections are correct,
confirm that you have a power supply and/or water supply. Then
follow these steps to trou leshoot the machine:
Diagram 1 1
1. Open the tap water inlet valve as well as the water purifier inlet water all valve, plug in the power
source (See Diagram 11), water will start to drain through the discharge outlet.
2. Wait for the water purifier to operate sta ly (a out 5-10 seconds), check each connection to make sure
it is secure, see if there is any leakage from the mem rane shells, filters, etc.
3. Close the pure water gooseneck faucet and storage tank all valve, wait approximately 30 seconds,
check whether or not the water purifier waste water has stopped.
4. Open the gooseneck faucet, o serve whether pure water is flowing through the faucet, if no pure water
is flowing, check whether the tap water pressure is too low or whether the high pressure switch cannot
e reset.
5. Wait until the machine is operating, close the inlet water all valve, after a short time o serve whether it
has stopped operating, if it has stopped operating, check whether the low-voltage switch can e reset.
6. Wait some time to make sure everything is correct, then the water purifier can e used safely.
7. Check the water quantity, which go to drain. It's should e according with the ta le 4.1
If the quantity of water is less than the information a ove it could
lead to quick failure of the mem ranes.
8. Check the TDS after some litters of water pass through the
gooseneck faucet. If the the mem ranes rejection is not very ig,
please take out every mem rane from the mem rane shell and
insert it again with clockwise and anticlockwise rotations. Check it
again.
Note: The pure water TDS could e higher after coconut activated
post car on filter till moment, when the unwanted active car on go
out.
-16-

Usage Methods
1. The major components of this product are plastic, when using the product always o serve the integrity
of the water purifier to ensure safe use.
2. In order to prevent micro ial contamination of mem rane components during storage and transportation
the reverse osmosis mem rane elements packages can contain a small amount of protective solution
while the coconut activated post car on filter will emit activated car on powder the first time it is used.
So, for the first hour the water purifier is operated, do not open the water storage tank. it is
recommended that the water produced is thrown out, otherwise the pure water taste may e unusual.
3. When you start operating the water purifier the pure water TDS value may e a little high, after running
for some time the TDS value for pure water will gradually decrease until it is sta le.
4. When you are using the water purifier, the inlet water all valve should e opened and the pure water
faucet needs to e turned on. When you are not using water turn off the water faucet, the high pressure
switch will automatically cut off the water supply.
5. In these “usage methods”, “usage” refers to when the power supply is connected and/or the inlet water
all valve is open so the water purifier is in a working condition.
Maintenance and Upkeep
1. Filter Replacement Time
① This machine’s filter replacement cycle for the various filters is derived from statistical indicators on
average tap water use estimates. If there are ig discrepancies etween the user’s actual water quality
and utilisation rate and the average indicators, there will e more o vious differences etween the filter’s
actual use time and the estimated cycle such as premature filter clogging, premature failure, etc. If this
happens, filter replacement should e ased on actual use, you should also promptly contact your local
after-sales service department.
② This machine’s estimated filter replacement cycle is ased on average household water consumption and
is suita le only for residential use, do not install this machine in places that require large volumes of
water. If the water volume requirements are large, this company has appropriate machines for usiness
purchase.
③According to economic statistics on municipal tap water, a three person family on average uses 10L of
water a day, according to the water volume and inlet water quality conditions, overall filter volume is
approximately as follows (the following data is for reference only):
Progression Times
First: 10-inch 5-micron PP filter 2-6 Months
Second: 10-inch car on lock CTO filter 3-6 Months
Third: 10-inch 1-micron PP filter 3-6 Months
Fourth: RO Mem ranes 2~~3 years
Fifth: Coconut activated post car on filter 1 Year
Note: It is recommended that filter element replacement is carried out b after-sales staff. Water
qualit has a great influence on the life of the filter, the RO membrane’s lifespan is affected b man
factors, the above table expresses lifespan under standard conditions, in actual usage, because the
water qualit ma be different, the lifespan ma exceed the above estimate, it ma also be lower
than the estimate, this data is for reference onl . Under normal circumstances if the following
situations are experienced, ou should consider replacing the filter:
-17-

Poor water quality, taste declines, TDS value of water rises;◆
Water flow is significantly reduced, check to see if the filter or mem rane is locked (and◆
determine that it was not caused y a temperature drop);
If the filter’s outer surface is covered in mud or the filter has significantly changed colour;◆
If serious filter clogging leads to no pure water from the water purifier.◆
2. Filter Replacement Method
① Replacing the 1st and 3rd stage PP filters
First close the inlet water all valve, using the filter cartridge wrench unscrew the 1st and 3rd stage filter
cartridges, remove the old filters, then take the new filters out of the packaging, finally place the filters in
the filter cartridges (Note: place the 5 micron PP filter in the 1st stage filter cartridge, the 1 micron PP filter
in the 3rd stage filter cartridge), using the filter wrench, tighten the filter cover.
②Replacing the 2nd stage car on lock CTO filter
First close the inlet water all valve, using the filter cartridge wrench unscrew the 2nd stage filter, remove
the old filter, then take the new filter out of its packaging (the ru er pad on the filter does not need to e
taken off), finally place the filter inside the filter cartridge, use the wrench to tighten the filter cover.
③For replacement of mem rane elements please see “RO Mem rane Installation” (Page 8).
3. Notes
① RO mem rane water production volume
The RO mem ranes components production volume dependence of the system model and it's
configuration.
② Disposal of old filters
After replacing old filters, they cannot e cleaned and reused; it is recommended that you dispose of
them with solid waste gar age.
Notes
When an of the following situations occur, immediatel disconnect the water purifier water★
source (close the inlet water ball valve) and/or the power source and carr out repairs.
· If the water purifier pipes or related components are leaking.
· If the water purifier’s related components stop working.
· If an components leak electricit .
· If there are an other anomalies or failures.
When ou go out or do not use the machine, disconnect the water purifier water source★
(close the inlet water ball valve) and/or power source.
If the water purifier parts are damaged, it is recommended that the water purifier be★
entrusted to the manufacturer or distributor, service center, or specialised technical
personnel for replacement to prevent loss caused b improper operation, the manufacturer
is not liable for losses caused b operation or use not in accordance with the instructions
and reminders.
-18-

Failure Diagnosis and Resolution
After-Sales Service
1. The warranty is valid from the date of installation.
3. Warranty period: Two-years machine warranty for the consumer in EU territories. The warranty
does not include consuma les (consuma les include filters, RO mem ranes, and storage tanks).
4. Please keep the warranty in a safe place, for maintenance you must have your purchase invoice,
only then is the warranty effective.
5. The final seller provides the warranty service.
6. The final seller can change the warranty conditions if the system installation wasn't made y seller's
specialist. The installation should e operated y professionals from the seller's side.
6. No invoice, altered machine num er, the user replacing parts or modifying the water purifier on their
own, the user not following the requirements of the user manual, and man-made damage do not fall
under the scope of the warranty.
-19-
Failure
Experienced
Reason Resolution Method
The machine
will not start
The power source is not connected Check the power source or the power
source plug
Low inlet water pressure or no water Check the inlet water pressure
Low-pressure switch failure, cannot connect the
power source
After connecting the inlet water,
measure the resistance, replace
High-pressure switch cannot e restored After letting off the pressure, measure
the resistance, replace
Switch Mode Power Supply is urned out Measure the output voltage, replace
The high
pressure pump
is working
properly, ut no
water is eing
produced
High-pressure pump has lost pressure Measure the water pump pressure,
replace
Inlet water solenoid valve is faulty, no water can
get in (no pure water)
Replace the solenoid valve
A pre-filter is locked O serve the pure water and waste
water, replace the pre-filter
Non return valve is locked (waste water, no
pure water)
Replace the non return valve
The RO Mem ranes is plugged Clean or replace the RO mem rane
The machine is
turned off ut
waste water
has not stopped
Inlet solenoid valve failed, cannot effectively cut
off the water supply
O serve the waste water, replace the
inlet solenoid valve
Non return valve has lost pressure (small waste
water flow rate)
O serve the waste water, replace the
non return valve
After the
machine is filled
with water, the
machine starts
repeatedly
Non return valve has lost pressure Replace the non return valve
High-pressure switch failure Replace the high pressure switch
System is exhi iting a loss of pressure After checking the non return valve,
check whether there is water leakage in
the pipelines
The pure water
flow is small or
not flowing
Pre-filter is plugged Replace the pre-filter
RO mem ranes is plugged Wash or replace the RO mem rane
Inlet solenoid valve failure Replace the inlet solenoid valve
Non return valve is plugged Replace the non return valve
Coconut activated post car on filter is plugged Replace the post-car on filter
High pressure pump pressure is not enough Measure the high pressure pump water
pressure, replace

9. If your water purifier exhi its a normal ehavior, please immediately turn of the water source, cut off
the power, and contact your local vendor.
Notes
The company reserves the right to change product design, configuration, and specifications without
notice.
The company has the final explanation rights if this manual is unclear, has mistakes, or if there were
printing pro lems which caused pro lems.
Packing List
· Main machine (including 2 units of RO mem ranes) 1 unit
· Water pipe (ø6mm) Each 1 roll
· Installation and User Guide 1 copy
· Gooseneck faucet 1
· Filter cartridge wrench 1
· Mem rane shell wrench 1
· Accessory pack
Consisting of：3 way inlet valve
Inlet water all valve
Pipe stopper ø6mm
Faucet hanging piece
Drain clamp
1 package
1
1
2
1
1
-20-