KSJ Photoelectrical Instruments Co. MG6-S1 User manual

GLOSSMETER
USER's MANUAL

Made in China
Add.: Middle of Binnan Street, Dongbin Industrial Zone, Donghai Bincheng,
Quanzhou 362000,
China
Tel.: [phone] Fax: [phone]
E-mail: [email protected]
Website:www.ksj.cn
KSJ Photoelectrical Instruments Co., Ltd.
www.glossmeter.cn
[email protected]

1.
CONTENTS
Specifications
Structure
Operation
Maintenance
Packing List
Warranty and Support
3
5
9
12
13
14

2.
All kinds of coating and finishing surfaces, such as paints, varnishes,
printing ink, etc.
Decorative materials, such as marble, granite, polishing brick, ceramic
tile and so on.
The other kinds of materials and objects, such as plastic, woodenware,
paper, etc.
Main Applications:
1
1
1
Thanks for your choice to purchase KSJ glossmeters.

SPECIFICATIONS <A>
Specifications Unit
Reading Range
Measuring Range
Resolution
Deviation
Zero-point Deviation
Stability
Measuring Area
Measurement Aperture
Incidence Angle
GU
GU
GU
GU
GU
GU
mm
60
20 10
30 14
3.

4.
Power Supply
Consumption
Main Volume mm3123 65 38
Main Weight g
Rechargeable or alkaline.
300
Specifications Unit
One AA-size battery, 1.2V 1.5V,
It's different to battery types. An alkaline battery
may last the meter to work more than 58 hrs.
SPECIFICATIONS <B>

5.
Ñ Front of Main Device
1
2
35 4
1
Front Cover
2
Measuring Mark
3
Info Labels
4
Measurement Aperture
5
Battery Cabin
STRUCTURE <A>

6.
Ñ Rear of Main Device
6
Display Screen
7
Calibration Knob
8
Knob Protector
9
On/Off Button
678
9
STRUCTURE <B>

7.
Ñ Holder With Calibration Tile
A
Holder
B
Calibration Tile (Working Standard)
C
Gloss Value Label
A
B
C
STRUCTURE <C>

8.
Ñ Battery Assembly Diagram
D
Front Cover
E
Cabin Cover
F
AA-size Battery
G
Rear Cover
D
E F
G
Positive Pole Down
STRUCTURE <D>

4
4
4
:
:
Power ON/OFF
Push On/Off Button to turn on the meter. To turn off just push it again.
Calibration
Turn on the meter and turn the Calibration Knob to adjust the reading
to the correct value that is labeled in the holder.
The main device must be located in the holder properly.
Measurement
Remove the holder and lay the Measuring Aperture just against the
position that you want to measure. The gloss value will be shown on
the Display Screen.
For an accurate result it is necessary to recalibrate the meter during
working.
9.
OPERATION

10.
Checking
After calibration, set the Measurement Aperture on the Checking Tile
( Spare Working Standard ). A deviation between the shown value and
the labeled value should be less than or equal to 1 GU. If the deviation
goes beyond this scope, it's shown that the certified gloss values of the
working standards may be changed. Thus the gloss values should be
certified again.
Check a meter only when it is used for a long period, or a result of
measurement is doubtful. It is not necessary to be check for every
time measuring.
4
:
OPERATION

Precautions
When measuring, the lens in the Measurement Aperture, the surface
of the Working Standards and samples should be kept clean. If the
surfaces have dust, steam or filth, they must be cleaned lightly with
lens paper or a soft cloth dipped in absolute ethanol.
Calibrating, measuring and checking should be carried out at a same
ambient temperature. Too big difference in temperature would bring
about the numerical excursion.
While measuring, keep environment light from directly irradiating into
the Measurement Aperture.
When the battery run out, a symbol of "bat" will appear on the Display
Screen, replace the old battery with a new one at once.
Please recalibrate a meter at regular intervals, e.g. 40 minutes .
11.
OPERATION

5
ù
ù
ù
ù
ù
ù
ù
Maintenance
The whole set of the meter should be kept in dry, ventilative and non-
corrosive environment.
If the meter is not in use, please put into the holder.
Keep the surface of the working standards clean, both the Calibration
Tile and the Checking Tile.
Remove the battery to prevent corrosion for a long period store.
After measurement, the meter should be turned off at once in order to
save energy .
Although the plastic parts of the meter are resistant to many solvents,
you should use a soft cloth dipped water or ethanol for cleaning.
For environment dispose the wasted batterys properly.
MAINTENANCE
12.

PACKING LIST
ÑMain Device Model: MG6-F1
MG6-S1
Ñ
Ñ
Ñ
Ñ
Ñ
Calibration
Holder with Calibrating Tile (Working Standard)
Checking Tile ( Spare Working Standard)
User Manual
Certification
Guarantee Card
1 set
1 piece
1 piece
1 piece
1 piece
13.

Limited Warranty and Technical Support
.
.
.
:
:
The limited warranty period is one year commencing on the date
of purchase.
We provide spare parts anytime for customers.
We also provide glossmeter customizing for a special application.
Note:
If your gloss meter needs service, carry it to the local
reseller for repair.
The meter should not be taken down at will in order to avoid
precision destroying and causing maintaining difficulty.
If the breakdown is caused by taking-down or inappropriate
use, we reserve the rights not to guarantee it free in repair.
14.

NOTE FOR MAINTENANCE
Date Signature
Description
15.