KT&C KPC-WDR7000NU User manual

HIGH RESOLUTION
WDR COLOR CAMERA
OPERATION MANUAL
Thank you for choosing our high quality camera.
Before attempting to connect or operate, please read and follow
these instructions.
M096-WDR7000-001

CONTENTS
1. CAUTIONS
2. FEATURES
3. COMPONENTS
4. NAME AND FUNCTION
5. INSTALLATION
6. DIMENSIONS
7. SPECIFICATION
8. OSD MANUAL
2

CONTENTS
1. CAUTIONS
2. FEATURES
3. COMPONENTS
4. NAME AND FUNCTION
5. INSTALLATION
6. DIMENSIONS
7. SPECIFICATION
8. OSD MANUAL
2

3
1. CAUTIONS
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions;
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
Note
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.”
WARNING
This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
Caution
Any changes or modications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
1. A regulated DC12V 500mA power supply is recommended for use with this camera
for the best picture and the most stable operation.
An unregulated power supply can cause damage to the camera.
When unregulated power supply is applied, product warranty will be out of subject.
2. It is recommended that the camera is used with a monitor that has a CCTV quality
75 video impedance level.
If your monitor is switched to high impedance then please adjust accordingly.
3. Do not attempt to disassemble the camera to gain access to the internal componets.
Refer servicing to your dealer.
4. Never face the camera towards the sun or any bright or reective light, which may
cause smear on the picture and possible damage to the CCD.
5. Do not remove the serial sticker for the warranty service.
6. Do not expose the camera to rain or other types of liquid.
7. The apparatus must be connected to a mains socket-outlet with a protective earthing
connection.

1. CAUTIONS
4
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with
separate collection systems)
This marking shown on the product or its literature, indicate that it should not
be disposed with other household wastes at the end of its working life. To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
This product should not be mixed with other commercial wastes purchased this
product, or their local government ofce, for details of where and how they can
take item for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract.
Household users should contact either the retailer where they for disposal.

2. FEATURES
• 1/3960H SONY Double Scan Super HAD CCD II
• High Resolution of 700TV Lines
• WDR (Wide Dynamic Range)
• OSD Function
• Multi Language
(English / Chinese / Russian / Spanish / German)
• Digital slow shutter
• 3DNR
• Privacy Zone 15Zone
• 3x Digital Zoom
• Motion Detect, Face Detection
• DC12V, DC12V / AC24V Dual Voltage
• RS-485 Communication
• True Day & Night With ICR Mechanism
5
How WDR makes better image?
WDR allows every detail to be captured accurately even if one
portion is bright while other portions are dark.

3. COMPONENTS
HIGH PERFORMANCE
WDR COLOR CAMERA
AUTO IRIS LENS
CONNECTION PLUG
C-MOUNT ADAPTOR RING
OPERATION MANUAL
6
*NOTE
PLEASE REMOVE PROTECTION FILM
Class 2 Only

4. NAME AND FUNCTION
• FRONT
7
TRIPOD MOUNTING HOLE(1/4"-20 UNC)
AUTO IRIS JACK
MOUNT COVER
C-MOUNT
ADAPTOR RING
TRIPOD MOUNTING HOLE(1/4"-20 UNC) BACK FOCUS CONTROL LEVER

4. NAME AND FUNCTION
• BACK
①. MENU BUTTON
②. UP BUTTON
③. DOWON BUTTON
④. LEFT BUTTON
⑤. RIGHT BUTTON
⑥. POWER LED
(The LED turns on when power is supplied)
⑦. VIDEO OUT JACK
(Used to connect an external video monitor in jack)
⑧. POWER TERMINAL
(User to connect an DC12V power source)
(Options : AC 24V/DC12V power source)
⑨. EXTERNAL CONTROL CONNECTOR
A - The camera can be controlled by using external controller such as the keyboard controller.
(RS-485 Communication)
B - Motion detection feature is to generate an alarm whenever movement occurs in the video.
When Motion Mode is set "ON" on the OSD menu of the camera.
-> Normal status : 0V
-> Motion detected : 3.3V
C - It can be switched to DAY mode or NIGHT mode by receiving the signal from external
light sensor or IR LED LAMP.
-> When +3.3V is applied, camera will be switched to BW mode.
-> When 0V is applied, camera will be switched to COLOR mode
CAUTION: Do not apply higher than 3.3V to D/N connector in order to prevent damage to the
camera.
8
DC12V DC12V/AC24V
AB C
EXTERNAL CONTROL
CONNECTOR
Class 2 Only Class 2 Only

9
5. INSTALLATION
• LENS CONNECTION
Lenses are sold separately. Lenses such as an auto iris lens,
CS-Mount lens and C-Mount lens can be used.
NOTE
• Please keep the lens clean.
• Any foreign objects and Finger marks on the lens can cause
inferior image quality in low light level conditions.
When using an auto iris lens
1. Please peel off about 8mm of the outer skin of the auto iris lens cable.
2. Please peel off about 2mm of the outer skin of the insulated conductor
inside the lens cable.

10
5. INSTALLATION
3. Please remove the cover of the auto iris lens connection plug and
solder the lens cable to the connector pin in the plug.
* PIN ASSIGNMENT OF THE LENS CONNECTOR
1) Video auto iris lens
Pin 1: Power source(DC 12V)
Pin 2: N.C(Not used)
Pin 3: Video signal
Pin 4: Shield, GND(Ground)
2) DC auto iris lens
Pin 1: DAMP-(CTL-)
Pin 2: DAMP+(CLT+)
Pin 3: DRV+
Pin 4: DRV-(GND)
4. Please replace the auto iris lens connection plug cover and take off the
Sensor protection cap and then attach the auto iris lens to the camera by
screwing it in clockwise.

5. INSTALLATION
5. Please insert the connection plug that is connected to the auto iris lens
cable into the auto lens connector, which is located on the side of the camera
11
C-mount lens : 10mm or less
CS-mount lens : 5mm or less
*NOTE
Use the lens under the specification as shown. Otherwise
the lens can damage the camera or abnormal fixing may result.

5. INSTALLATION
Installation of C-Mount Lens
Installation of CS-Mount Lens
12
C-MOUNT ADAPTOR RING

5. INSTALLATION
• MONITOR CONNECTION
(1) DC12V
(2) DC12V/AC24V
* As the connecting method varies with instruments, refer to the
manual supplied with the instrument.
* Only connect the cable when the power is turned off.
* Set the 75Ω / Hi-Z selection switch as shown below if you have an intermediate device
13
DC12V REGULATED
POWER SUPPLY
BNC FEMALE
VIDEO
VIDEO IN
DC12V / AC24V REGULATED
POWER SUPPLY
BNC FEMALE
VIDEO
VIDEO IN
Class 2 Only
Class 2 Only
Class 2 Only

14
6. DIMENSIONS
Unit(mm)
143.5(C-Mount)
138.5(CS-Mount)
AUTO IRIS JACK
TRIPOD MOUNTING HOLE
C-MOUNT ADAPTOR RING
72.5
66
TRIPOD MOUNTING HOLE
(1/4"-20 UNC, Depth 5)

7. SPECIFICATION
15
Signal Format NTSC PAL
Image Device 1/3” 960H SONY Double Scan Super HAD CCD II
Scanning System 2:1 Interlace
H.Resolution 750TV Lines
Scanning Frequency H:15.734KHz, V:59.94Hz H:15.625KHz, V:50Hz
Total Pixels 1028(H) X 508(V) 1028(H) X 596(V)
Effective Pixels 976(H) X 494(V) 976(H) X 582(V)
Electronic Shutter 1/60 ~1/100,000sec 1/50 ~1/100,000sec
Digital Zoom Ratio 3x
Digital Slow Shutter OFF, 2 ~ 128 Field
Flickerless ON / OFF
WDR ON / OFF (Level adjustable)
BLC ON / OFF (Level adjustment, Area selection)
3DNR ON / OFF (Level adjustable)
Image Function Image reverse(NORMAL/H / V / HV), Freeze
Sharpness Level adjustable
AGC LOW / MID / HIGH
Day & Night True Day & Night with ICR Mechanism (COLOR / BW / AUTO / EXT)
Motion Detection ON / OFF (Level adjustable, Area adjustment)
Face Detection ON / OFF (Level adjustable, Area adjustment)
Privacy Masking 15 Zones (Area adjustment)
White Balance ATW / PUSH / PUSH LOCK / MANUAL(R Gain, B Gain)
OSD Built in
Language English / Chinese / Russian / Spanish / German
Protocol Pelco"D"
Baud Rate 2400 / 4800 / 9600 / 19200
S/N Ratio More than 50dB(3DNR ON)
Gamma r=0.45
Min. Illumination 0.08Lux(Color) / 0.04Lux(BW) ([email protected], AGC:HIGH)
Sync System Internal
Video Output 1.0 Vp-p Composite 75(Ω) unbalanced
Lens C / CS (DC\VIDEO)
Power
Consumption
DC12V DC 12V ±10%, Max 210mA
DUAL DC 12V ±10%, Max 270mA / AC 24V ±10%, Max 3.9W
Operating Temperature 14°F~122°F(-10°C~+50°C)
Storage Temperature -4°F~140°F(-20°C~+60°C)
Humidity Less than 80%
External Control RS485 Communicition
Weight 400g
Dimensions(mm) 72.5mm x 66mm x 138.5mm

16
8. OSD MANUAL
GENERAL STRUCTURE
SETUP
>LENS [-]
EXPOSURE [-]
WHITE BALANCE [-]
WDR/BLC [-]
DAY&NIGHT [-]
IMAGE [-]
SPECIAL [-]
FACTORY DEFAULT
EXIT
LENS
>LENS TYPE ... DC
LEVEL ... 08
INITIAL
RETURN
EXPOSURE
>SHUTTER ... 1/60
FLICKERLESS ... OFF
AGC ... MID
DSS ... 10x
INITIAL
RETURN
WHITE BALANCE
>WB MODE ... ATW
RED CONT ... ----
BLUE CONT ... ----
PUSH CONT ... ----
INITIAL
RETURN
WDR/BLC
>WDR MODE ... OFF
WDR LEVEL ... 08
BLC ... OFF
BLC ZONE ... CENTER
BLC LEVEL ... 04
INITIAL
RETURN
• ▲,▼ : Menu up / down
• ◀,▶ : Menu left / right
• ○ : MENU

17
8. OSD MANUAL
MOTION DET
>MOTION MODE ... ON
LEVEL ... 08
FACE MODE ... ON
LEVEL ... 07
V START ... 01
V END ... 06
H START ... 01
H END ... 10
INITIAL
RETURN
PRIVACY
>ZONE NO ... 0
MASK ... OFF
V START ... 07
V END ... 12
H START ... 10
H END ... 19
TOP ANGLE ... 00
BOTTOM ANGLE ... 00
INITIAL
RETURN
DAY & NIGHT
>D&N MODE ... COLOR
DWELL TIME ... ----
D -> N LEVEL ... ----
N -> D LEVEL ... ----
INITIAL
RETURN
IMAGE
>REVERSE ... NORMAL
DNR ... OFF
DNR LEVEL ... 4
SHARPNESS ... 10
FREEZE ... OFF
D-ZOOM .. 1,0x
INITIAL
RETURN
SPECIAL
>CAM TITLE ... [-]
LANGUAGE ... ENGLISH
COMM ADJ ... [-]
PRIVACY ... [-]
MOTION DETECT ... [-]
DISPLAY ... [-]
INITIAL
RETURN
CAM TITLE
0123456789ABCDEFGHIJKLMN
OPQRSTUVWXYZ!?*#$%()<>{}
SPACE >> <<BACK
LOCATION ... [┛]
RETURN
DISPLAY
>CAM ID ... OFF
CAM TITLE ... OFF
MOTION DETECT ... OFF
FACE DETECT ... OFF
INITIAL
RETURN
[TITLE LOCATION]
TITLE
[U] [D] [L] [R] [M] +
CAMM ADJ
>CAM ID ... 000
BAUDRATE ... 9600
RETURN

18
8. OSD MANUAL
LENS MENU STRUCTURE
EXPOSURE MENU STRUCTURE

19
8. OSD MANUAL
WHITE BALANCE MENU STRUCTURE
WDR MENU STRUCTURE