KT&C VDS302 User manual

Resolution 960 Series
750+ HTVL Varifocal
3-Axis Dual Voltage IP68 Vandal Dome Camera
Operation Instructions
Model No. VDS302
Please read this manual rst for correct installation and operation.
This manual should be retained for future reference.
The information in this manual was current when published.
The manufacturer reserves the right to revise and improve its products.
All specications are therefore subject to change without notice.
M201-VDS302-001

CONTENTS
1. CAUTIONS
2. PRECAUTIONS
3. FEATURES
4. PRODUCT OVERVIEW
5. EQUIPMENT AND ACCESSORIES
6. OVERVIEW AND FUNCTION
7. INSTALLATION
8. CONNECTION
9. DIMENSIONS
10. SPECIFICATION
11. OSD MENU STRUCTURE
2
These servicing instructions are for use by qualied service personnel only.
To reduce the risk of electric shock do not perform any servicing other than
that contained in the operating instructions unless you are qualied to do so.
Use Class 2 Power Supply Only
CAUTION

1. CAUTIONS
3
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
Note
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct
the interference at his own expense.
WARNING
This is a class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
Caution
Any changes or modifications in construction of this device which are not
expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
1. A regulated DC12V or AC24V power supply with a minimum of 500mA / 10VA is
recommended for use with this product for the best picture and the most stable operation.
An unregulated power supply can cause damage to the product.
If an unregulated power supply is used, product warranty will be void.
2. It is recommended that cables and monitors with a 75ohm video impedance level are
used with this product.
If your monitor supports high impedance mode, then please adjust accordingly.
3. Do not disassemble the camera to gain access to the internal components.
Refer servicing to your dealer.
4. Pointing the camera directly towards the sun, or any similarly bright or reective light,
may cause smear and possible damage to the sensor.
5. Removing the Serial Number Label will void the warranty.
6. The camera’s power supply must be plugged into a properly grounded wall socket.

1. CAUTIONS
4
WEEE
(Waste Electrical & Electronic Equipment)
This marking shown on the product or its literature, indicates that it should
not be disposed with other household wastes at the end of its working life. To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources. Household
users should contact either the retailer where they purchased this product, or
their local government ofce, for details of where and how they can take item
for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract.
This product should not be mixed with other commercial wastes for disposal.
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL
This symbol is intended to alert the user to the presence
of un-insulated “dangerous voltage” within the product’s
enclosure that may be of sufcient magnitude to constitute a
risk of electric shock.
This symbol is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions
in the literature accompanying the appliance.

2. PRECAUTIONS
1. Do not install the camera near electric or magnetic elds.
Install the camera away from TV/radio transmitters, magnets, electric motors,
transformers and audio speakers since the electromagnetic elds generated from these
devices may distort the video image or otherwise interfere with camera operation.
2. Never disassemble the camera beyond the recommendations in this manual nor
introduce materials other than those recommended herein. Improper disassembly or
introduction of corrosive materials may result in equipment failure or other damage.
3. Try to avoid facing the camera toward the sun.
In some circumstances, direct sunlight may cause permanent damage to the sensor and/
or internal circuits, as well as creating unbalanced illumination beyond the capability of
the camera to compensate.
4. Keep the power cord away from water and other liquids and never touch the
power cord with wet hands. Touching a wet power cord with your hands or touching
the power cord with wet hands may result in electric shock.
5. Never install the camera in areas exposed to oil, gas or solvents.
Oil, gas or solvents may result in equipment failure, electric shock or, in extreme cases,
re.
6. Cleaning
For cameras with interchangeable lenses, do not touch the surface of the sensor directly
with the hands. Use lens tissue or a cotton tipped applicator and ethanol to clean the
sensor and the camera lens. Use a damp soft cloth to remove any dirt from the camera
body. Please do not use complex solvents, corrosive or abrasive agents for cleaning of
any part of the camera.
7. Do not operate the camera beyond the specied temperature, humidity or power
source ratings. This camera is suitable for indoor operation only. Use the camera at
temperatures within -40°C~60°C (-40°F~140°F) and humidity between 20% and 80%.
This device is not rated as submersible. The input power source is 12VDC / 24VAC
regulated.
8. Mounting
Use care in selecting a solid mounting surface which will support the weight of the camera
plus any wind, snow, ice or other loading, and securely attach the camera to the mounting
surface using screws and anchors which will properly support the camera. If necessary
(e.g. when mounting to drop ceilings) use a safety wire to provide additional support for
the camera.
5

3. FEATURES
• Superlative resolution of over 750 horizontal TV lines for amazing image quality.
• 960H CCD for sensor sensitivity of .001 lux in low light without DSS boost.
• Full motion color or digital day/night during low ambient light without ghosting.
• Simple and easy to use OSD setup menu.
- Adaptive Tone Curve Reproduction (ATR)/Electronic Wide Dynamic Range to
properly expose images during unbalanced light contrast in the scene.
- Anti Color Roll white balance option resists uorescent light interference
- Optional Back Light Compensation (BLC) and Highlight Compensation. (HLC)
- Adjustable 2D-Noise Reduction to increase picture clarity and improve utilization
of DVR disk storage.
- Privacy image masking for 4 congurable zones.
• 2.8~11mm Aspheric Varifocal DC iris lens to capture the desired eld of view.
• Dual voltage (12VDC/24VAC) with Anti Color Roll.
• IP68 waterproof.
• Extreme Operating temperature down to -40 degrees.
• Service Video output for convenient installation,
and ease of service.
• 3-Axis gimbal for convenient wall or ceiling mounting.
• Optional wall mount arm. (KA-WM100)
6

4. PRODUCT OVERVIEW
Take advantage of the new Resolution 960 Series technology with the 960H cameras
that deliver 750+ HTVL and more. To achieve the amazing resolution of this advanced
imaging technology, the KPC-VDS302 uses a 960H CCD sensor on these Resolution 960
cameras to produce over 750 horizontal TV lines of resolution. Combined with a sensor
native low light sensitivity of 0.001 lux, this camera truly delivers everything you want
in an outdoor analog camera: crystal clear images, Electronic Wide Dynamic Range to
maintain the clarity of those color images in the most challenging of bright or unbalanced
scene lighting conditions, plus excellent low light performance and wide temperature
range operation as low as -40°F up to 140°F with low current draw. The KPC-VDS302
offers exible positioning for wall or ceiling mounting in an IP68 waterproof, vandal
resistant housing; 2.8~11mm varifocal DC Iris lens; dual voltage (12VDC/24VAC) with
Anti Color Roll and many DSP functions (DNR to save DVR HDD space, digital WDR,
BLC, HLC, anti-color roll for stability under uorescent lighting). For an alternate surface
mounting conguration, add a wall mount arm (KA-WM100).
5. EQUIPMENT AND ACCESSORIES
DOME
CAMERA
This User Guide
Template
Screws(4ea) / Plastic anchors(4ea)
/ Wrench / Screws(1ea)
Service Video Output Test Cable /
Wrench / Screws(4ea) / Pigtail Jack
7

6. OVERVIEW AND FUNCTION
8
• CONTROL FUNCTION
(OSD JOYSTICK)
LEFT
UP
RIGHT
DOWN
Service Video Connector
OSD Joystick
Pan Rotation Tilt Rotation Axial Rotation
• 3-Axis gimbal.
• Optional wall mount arm.
(KA-WM100)

7. INSTALLATION
9
Separate Circuit Cover and adjust
LENS ZOOM / FOCUS KNOB.
After setting the lens, assemble
the Circuit Cover.
Cover Screws(4ea)
are captive and will normally be
retained in cover. They are shown here
for illustration purpose.
Screws(4ea)
Plastic Anchors(4ea)
Circuit Cover
Template
Lens Zoom Knob
Lens Focus Knob
Tilting angle
70˚

When you install the camera, please glue up the end of cable to
keep it stable in order to protect the camera from the humidity problems.
8. CONNECTION
• DC 12V / AC24V
10
DC 12V / AC 24V
POWER SUPPLY
PIGTAIL JACK
VIDEO IN

9. DIMENSIONS
Unit : Inch(mm)
11
Ø5.92 (150.5)
Ø3.93 (100)
4.27 (108.5)
2.35 (59.8)

10. SPECIFICATION
Imaging Device 1/3" 960H High Sensitivity CCD
Video Format NTSC
Picture Elements NTSC: 1020(H)x508(V)
Effective Picture Elements NTSC: 976(H) x 494(V)
Horizontal Resolution More than 750 TVL
Sensitivity .001 lux native from sensor, with Lens: .2 lux
S/N Ratio Over 50dB (AGC off)
Video Output BNC 1.0V p-p 75Ω; video test point inside dome, cable supplied
Gamma Correction 0.45
Lens Type Varifocal DC Iris 2.8~11mm F=1.6
Lens Positioning 3-axis exible positioning for wall or ceiling mounting
Back/High Light Compensation OFF / BLC / HLC Selectable
Auto Gain Control Off / Low / Middle / High
Electronic Shutter Auto; or 1/60, FLK, 1/250, 1/500, 1/1000,
1/2000, 1/4000, 1/5000, 1/10000, 1/100000
White Balance ATW/AWB/AWC->SET/Anti-Color Roll/Manual
Sync. Mode Internal (plus Anti-Chroma Crawl White Balance option above)
Day & Night Electronic D/N operation, controlled by photo sensor
OSD Menu Multiple functions using 3-axis joystick
OSD Languages English, Spanish, Portuguese, German,
Russian, Japanese, Chinese, French
2D-DNR On / Off (level adjustable)
Digital Wide Dynamic Range On / Off (level adjustable)
Mirror Off / On
Motion Detection Off / On for 4 selectable zones (On screen indication)
Privacy Mask Off / On for 8 selectable zones
Lens Shading Correction Off / On with adjustable level and center
Other OSD Functions
Camera Title with position, Font Color, Image Contrast/Sharpness,
CRT/LCD display optimization, Negative Image,
DPC(Dead Pixel Compensation)
Power Source 12VDC/24VAC
Power Consumption 12VDC:170mA max. / 24VAC:2.3W max.
Operating Temperature -40°F~140°F ; -40°C~60°C
Environmental IP68 waterproof
Mechanical Vandal proof dome
Dimensions 5.92”/150.5mm dia. x 4.27”/108.5mm high
Weight 1.92 lb. / 869g
Mounting Options Direct ceiling or wall mount (3-axis positioning)
Optional wall mount arm (KA-WM100)
Certications CE / FCC / RoHS
12

11. OSD MENU STRUCTURE
• Menu structure
Main 1st Sub Menu 2nd Sub Menu 3rd Sub Menu
LENS
DC
BRIGHTNESS 0 ~ 255
IRIS SPEED 0 ~ 15
RETURN SAVE&END
MANUAL BRIGHTNESS 0 ~ 255
RETURN SAVE&END
EXPOSURE
SHUTTER
AUTO
1/60(NTSC),1/100(NTSC),FLK,
1/250,1/500,1/1000,1/2000,1/4000
1/5000,1/10000,1/100000
AGC - - -
DWDR OFF/ON 0 ~ 63
RETURN SAVE&END
RETURN SAVE&END
WHITE
BALANCE
ATW
AWB
AWC -> SET
ANTI. CRL
MENUAL
COLOR TEMP
MENUAL
INDOOR
OUTDOOR
BLUE 0 ~ 255
RED 0 ~ 255
RETURN SAVE&END
BACKLIGHT
OFF
BLC
AREA SEL. AREA 1
AREA 2
AREA STATE OFF/ON
GAIN 0 ~ 255
HEIGHT 0 ~ 15
WIDTH 0 ~ 15
LEFT/RIGHT 0 ~ 15
TOP/BOTTOM 0 ~ 15
RETURN SAVE&END
HLC
OFF
HLC
LEVEL 0 ~ 255
MODE NIGHT ONLY
ALL DAY
MASK SKIP
OFF / ON
HEIGHT 0 ~ 15
WIDTH 0 ~ 15
LEFT / RIGHT 0 ~ 15
TOP / BOTTOM 0 ~ 15
RETURN SAVE&END
RETURN SAVE&END
13

11. OSD MENU STRUCTURE
Main 1st Sub Menu 2nd Sub Menu 3rd Sub Menu
DAY&NIGHT
AUTO
D->N LEVEL 0 ~ 255
D->N DELAY 1, 3, 5, 10, 15, 20, 25, 30
N->D LEVEL 0 ~ 255
N->D DELAY 1, 3, 5, 10, 15, 20, 25, 30
RETURN SAVE&END
COLOR
BW
BURST
IR SMART
OFF / ON
IR GAIN 0 ~ 255
HEIGHT 0 ~ 15
WIDTH 0 ~ 15
LEFT / RIGHT 0 ~ 15
TOP / BOTTOM 0 ~ 15
RETURN SAVE&END
RETURN SAVE&END
*IR SMART Feature:
IR SMART feature can only be adjusted when DAY&NIGHT is set to BW.
IR SMART feature adjusts AE LEVEL to prevent a subject being too bright from excessive IR light.
After chaning the IR SMART function under BW mode, make sure to switch the AUTO mode to SAVE mode before
saving the setting.
SAVE is the normal operating mode that should be used for this camera.
Leaving the mode under BW when saving will result in constant BW mode output.
SPECIAL
CAM TITLE
OFF/ON
0 1 2 3 4 5 6
7 8 9 A B C D E
F G H I J K L M
N O P Q R S T U
V W X Y Z → ←
↑ ↓ ( ) - _ ■
/ = : " . , ┛
← → CLR POS END
MOTION
OFF/ON
AREA SEL.
AREA1
AREA2
AREA3
AREA4
AREA STATE OFF/ON
HEIGHT 0 ~ 15
WIDTH 0 ~ 15
LEFT/RIGHT 0 ~ 15
TOP/BOTTOM 0 ~ 15
DEGREE 0 ~ 255
VIEW OFF/ON
RETURN SAVE&END
14

11. OSD MENU STRUCTURE
Main 1st Sub Menu 2nd Sub Menu 3rd Sub Menu
SPECIAL
PRIVACY
OFF / ON
AREA SEL. AREA1 / AREA2 / AREA3 / AREA4
AREA5 / AREA6 / AREA7 / AREA8
AREA STATE OFF / ON
HEIGHT 0 ~ 15
WIDTH 0 ~ 15
LEFT / RIGHT 0 ~ 15
TOP / BOTTOM 0 ~ 15
COLOR 0 ~ 15
RETURN SAVE&END
IMAGE ADJ
LENS SHAD.
OFF / ON
LEVEL 0 ~ 255
H-CENTER 0 ~ 255
V-CENTER 0 ~ 255
RETURN SAVE&END
2DNR
OFF / ON
LEVEL 0 ~ 15
RETURN SAVE&END
MIRROR OFF / ON
FONT COLOR
FONT 0 ~ 15
ID&TITLE 0 ~ 15
RETURN SAVE&END
CONTRAST 0 ~ 255
SHARPNESS 0 ~ 31
DISPLAY
CRT
PED LEVEL (0 ~ 63)
COLOR GAIN (0 ~ 255)
RETURN (SAVE&END)
LCD
GMMA (0.3 ~ 1.0)
PED LEVEL (0 ~ 63)
COLOR GAIN (0 ~ 255)
RETURN (SAVE&END)
RETURN SAVE&END
NEG. IMAGE OFF / ON
RETURN SAVE&END
LANGUAGE ENGLISH / CHINESE / SPANISH / RUSSIAN / GERMAN / PORTUGUESE
FRENCH / JAPANESE
DPC
START
DPC VIEW OFF / ON
LS VALUE (0 ~ 63)
DIFF (0 ~ 63)
AREA HS (0 ~ 255)
AREA HE (0 ~ 255)
AREA VS (0 ~ 255)
AREA VE (0 ~ 255)
RETURN SAVE&END
RETURN SAVE / NOT SAVE / RESET
*Important Note:
- Any changes made to the camera settings must be saved prior to exiting the OSD menu.
Else all changes will be discarded.
15

New Jersey Ofce
40 Lane Road 1st Floor
Faireld, NJ 07004
T: 973-276-0118
F: 973-276-0116
New York Ofce
200 Parkway Drive South Suite 200
Hauppauge, NY 11788
T: 631-864-0118
F: 631-864-0116
California Ofce
3240 Wilshire Blvd. Suite 501
Los Angeles, CA 90010
T: 213-381-0061
F: 213-381-0064
KT&C America, Inc.
www.ktncusa.com