KT&C KPC-HZA302M User manual

HD CCTV
Mega Pixel 30X ZOOM
COLOR CAMERA
OPERATION MANUAL
Thank you for choosing our high quality camera.
Before attempting to connect operate this unit, please read and follow these instructions.
M180-HZA302-001
All manuals and user guides at all-guides.com
all-guides.com

These servicing instructions are for use by qualied service personnel only.
To reduce the risk of electric shock do not perform any servicing other than that
contained in the operating instructions unless you are qualied to do so.
Use Class 2 Power Supply Only
CAUTION
2
All manuals and user guides at all-guides.com

CONTENTS
1. CAUTIONS
2. IMPORTANT SAFETY INSTRUCTION
3. FEATURES
4. COMPONENTS
5. NAME AND FUNCTION
6. INSTALLATION
7. DIMENSIONS
8. SPECIFICATION
9. OSD MENU STRUCTURE
3
All manuals and user guides at all-guides.com

1. CAUTIONS
1. A regulated DC12V 1A power supply is recommended for use with this camera
for the best picture and the most stable operation.
An unregulated power supply can cause damage to the camera.
When unregulated power supply is applied, product warranty will be
out of subject.
2. It is recommended that the camera is used with a monitor that has a CCTV quality
75Ω video impedance level.
If your monitor is switched to high impedance then please adjust accordingly.
3. Do not attempt to disassemble the camera to gain access to the internal components.
Refer servicing to your dealer.
4. Never face the camera towards the sun or any bright or reective light, which may
cause smear on the picture and possible damage to the Image Sensor.
5. Do not remove the serial sticker for the warranty service.
6. Do not expose the camera to rain or other types of liquid.
7. The apparatus must be connected to a mains socket-outlet with a protective
earthing connection.
4
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions;
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference
that may cause undesired operation.
Note
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.”
WARNING
This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
Caution
Any changes or modications in construction of this devices which are not expressly
approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
All manuals and user guides at all-guides.com

1. CAUTIONS
5
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with
separate collection systems)
This marking shown on the product or its literature, indicate that it should not
be disposed with other household wastes at the end of its working life. To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
This product should not be mixed with other commercial wastes purchased this
product, or their local government ofce, for details of where and how they can
take item for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract.
Household users should contact either the retailer where they for disposal.
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER(OR BACK). NO USER. SERVICING
TO QUALIFED SERVICE PERSONNEL.
This symbol is intended to alert the user to the presence of
uninsulated "dangerous voltage" within the product's enclosure that
may be of sufcient mangnitude to constitute a risk of electric shock
to persons.
This symbol is intended to alert the user to the presence of
important operating and maintenance(servicing) instruction in the
literature accompanying the appliance.
All manuals and user guides at all-guides.com

2. IMPORTANT SAFETY INSTRUCTION
6
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including ampliers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade or the third
prong are provided for your safety. If the provided plug does not t into your outlet,
consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specied by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specied
by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long
periods of time.
14) Refer all servicing to qualied service personnel. Servicing is required when
the apparatus has been damaged in any way, such as power-supply cord or plug
is damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or
has been dropped.
All manuals and user guides at all-guides.com
all-guides.com

3. PRECAUTIONS
Do not operate under extreme temperature conditions.
Using the camera in temperatures exceeding 50˚C or below -10˚C may
lower image quality or cause the camera to malfunction.
Do not operate in high humidity environments.
Using the camera in places with high humidity may lessen picture quality
because of moisture on the lens.
Do not operate under unsteady lighting.
The camera will not work properly in places with great changes in
illumination intensity, such as uorescent lamps.
Do not attempt to disassemble the camera.
Do not drop the camera or subject it to physical shock.
It may damage the camera if dropped or subjected to strong impact.
Do not exposed to an intense light source such as direct sunlight
It may damage the CMOS.
Do not exposed the camera to rain or other types of liquids.
It may damage the camera.
Do not exposed the camera to radioactivity.
It may damage the CMOS.
7
• Exposure to a spotlight or an object emitting strong light may cause smear or
blooming.
• Ensure that the power source complies with normal specications before supplying it
to the camera.
NOTE
All manuals and user guides at all-guides.com

4. FEATURES
1) 1/2.8” Sony CMOS Sensor
2) X30 Optical Zoom
3) 1080P 60fps Resolution
4) WDR (Wide Dynamic Range)
5) DNR (Digital Noise Reduction)
6) LSC (Lens Shading Compensation)
7) DIS (Digital Image Stabilizer)
8) Digital Effect (Mirror, Freeze, Negative)
9) Motion Detection/
10) Privacy Masking
11) Defog
12) Day & Night (Auto, EXT)
13) Multi-format Simultaneous Outputs (3G-SDI HDMI / CVBS )
14) Multi Protocol
8
All manuals and user guides at all-guides.com

5. COMPONENTS
Package
Operation
Manual
Operation Manual 30x Zoom Camera
Tripod Mounting Hole
Install the camera on an optional tripod.
The tripod must be equipped with screws with
specications shown on the right.
Tripod Mounting
Tripod Mounting bracket is assembled
to the top and buttom of the camera.
9
All manuals and user guides at all-guides.com

6. DIMENSIONS
Unit:mm
10
67
73
121.8
62.7 12
1/4” - 20NUF
All manuals and user guides at all-guides.com

7. OVERVIEW
Rear View
Key Buttons
•Following buttons control zoom, focus, and auto focus functions.
W(WIDE) button : To widen the view. (ZOOM OUT)
T(TELE) button : To close in on a far object. (ZOOM IN)
N(NEAR) button : To see a near object clearly.
F(FAR) button : To see a far object clearly.
• Pressing the M(MENU) button prompts the main setup menu.
•Setup menu can be navigated using these buttons.
MENU(M) button : To access the main setup menu.
UP(T) button : To move the arrow indicator to up.
DOWN(W) button : To move the arrow indicator to down.
LEFT(N) button : To change date to down.
RIGHT(F) button : To change date to up.
Control Interface
• Used to connect the remote control equipment.
Includes the RS-485 communication pin.
Zoom and focus functions can be controlled by using external signals.
Power LED
• Illuminates when power is supplied.
Video Output Jack
• Used to connect an external video monitor in jack.
Power Input Terminal
• Power supply terminal(DC12V± 10%)
11
Power LED
Power Input
Terminal
Control
Interface
Key Buttons
Video Out Jack
HDMI
HD-SDI Jack
All manuals and user guides at all-guides.com
all-guides.com

8. INSTALLATION
Connecting to Monitor
• Connect Video Out Jack to the monitor’s Video In Jack as shown below.
• Connection methods may vary depending on the video equipment. Please refer to
the model specic instruction manual.
12
BNC Female
Video
HDMI CABLE
BNC Female
Video
All manuals and user guides at all-guides.com

13
8. INSTALLATION
Connecting to Power
Connect the power cable to the camera’s power in as shown in the gure below
Resistance of copper wire [at 20℃ (68˚F)]
Copper wire size
(AWG)
#24
(0.22㎟)
#22
(0.33㎟)
#20
(0.52㎟)
#18
(0.83㎟)
Resistance(Ω/m) 0.078 0.050 0.030 0.018
Voltage Drop(V/m) 0.028 0.018 0.011 0.006
• As the voltage drop according to the length of the cable in the above table, a
camera may malfunction if there is an excessively long cable run.
• Voltage drops in the above table are variable according to types of cable
manufacturer.
• Connect the power once the installation is complete.
• When connecting to the power source, make sure the polarity of the power adapter
is correct.
• Use a DC12V/500mA power source for the camera.
NOTE
DC12V Regulated Power Supply
All manuals and user guides at all-guides.com

14
8. INSTALLATION
Control Interfaces(Communication Control Connector)
The camera can be controlled by using external controllers like as the keyboard controller.
(RS-485 Communication)
Connecting PC or DVR (Serial Port)
Connecting to RS-485 Controller
RS-232C TO RS-485 CONVERTER
All manuals and user guides at all-guides.com

15
8. INSTALLATION
Connecting to External Controller
EXT & GND Open: DAY
EXT & GND Close: NIGHT
All manuals and user guides at all-guides.com

16
9. SPECIFICATION
Image Device 1/2.9” Sony Exmor CMOS Sensor
Effective Pixels About 2.14Mega pixel
Minimum illumination 0.6 lx (F1.6, 30IRE, ICR OFF) / DSS on: 0.02 lx
0.06 lx (F1.6, 30IRE, ICR ON) / DSS on: 0.002 lx
Lens x30 (f=4.3 ~ 129.0mm), F1.6(Wide)~F5.0(Tele)
View of angle Horizontal : 65.1° (Wide end) to 2.34° (Tele end)
Digital Zoom (PIP, PTZ) OFF ~ x10 Variable (Total x300)
AF AUTO / ONE SHOT / MANUAL
White Balance ATW / AWC / OUTDOOR / INDOOR/MANUAL
Day & Night AUTO / SENSOR / VIDEO / EXT
3DNR OFF/1~5
WDR/HLC/BLC ON/OFF (User Setting)
DEFOG OFF/LOW/MIDDLE/HIGH (User Setting)
AGC OFF~42dB
Digital Image Stabilization ON/OFF
Digital Slow Shutter ON/OFF (x2 ~ x30 Variable)
Shutter Control AUTO/IRIS FIX/SHUTTER FIX/GAIN FIX/MANUAL
Privacy Zone Masking ON/OFF (8 Rectangle areas)
Communication RS-485, VISCA protocol, Pelco-D/P
Image Processing Image Flip / Mirror / Motion Detection(4 areas)
Digital Zoom PIP(Only 1080P 30fps)
Digital Video Output HDMI
MAX. 3G-SDI IF 1080P@60fps
Analog Video Output 960H or 760H Composite Output 1Vp-p
(75 Ohm Terminal)
Operating Temperature -5°C ~ +50°C
Storage Temperature -20°C ~ +60°C
Dimension (W x H x D) 67 x 121.8 x 73mm
Power Consumption DC 12V (±10%), Max 550mA (60fps, motor active)
Specifications and designs are subject to change for improving the
functionality of this product without notice.
All manuals and user guides at all-guides.com
all-guides.com

17
10. OSD MENU STRUCTURE
OSD Working
• Entering Main menu
A. If you press ENTER button for more than 3sec then menu will appear on the monitor.
B. If you press TELE button then cursor will move to UP MENU BAR, and if you press
WIDE button then cursor will move to DOWN MENU BAR.
C. After you select a Main-menu, if you press ENTER button then menu-bar will move
to Sub-menu.
• Moving to Sub-menu
A. If you press NEAR button, value will be decreased, and if you press FAR button,
value will be increased.
B. After you select a Sub-menu, IF you press ENTER button then menu-bar will move
to Sub-menu.
C. To return Main-menu, move menu-bar to RETURN and press ENTER.
MAIN MENU
LENS SETUP
AE SETUP
AWE SETUP
SMART SETUP
ADVANCED SETUP
GENERAL SETUP
FACTORY RESET
EXIT
LENS SETUP
AF MODE ONESHOT
AF SENSITIVITY 5
AF TIME 10 SEC
ONE. AF TIME OFF
MIN. DIST 1M
ZOOM SPEED FAST
ZOOM LIMIT OFF
EXIT RETURN
All manuals and user guides at all-guides.com

10. OSD MENU STRUCTURE
• Exiting from Menu
A. At Main-menu, move menu-bar to EXIT MENU, and press ENTER button.
B. At Sub-menu, move menu-bar to EXIT MENU, and press ENTER button.
C. EXIT : The changed values will be stored.
Menu details
• LENS SETUP
At Main-menu, select LENS SETUP MENU, and press ENTER button.
1. AF MODE
: Set AF MODE
AF MODE: AUTO →MANUAL →ONESHOT
AUTO: Use to focalize automatically all the time.
MANUAL: Use to focalize manually pushing NEAR or FAR key.
Even though MANUAL mode, it will be focalizeds in some time after zoom
in or out, and then return to MANUAL mode automatically.
So you can change the focus manually.
ONESHOT: It is same with MANUAL mode in function aspect. But it focalizes whenever
you push ONESHOT key.
This function is similar to manual mode, but only when the key(Menu/Tele/
Wide) is pressed, It will be focusing.
ONESHOT act automatically, It will be returned to MANUAL mode in 5
seconds.
2. AF SENSITIVITY
: You can adjust sensitivity of AUTO FOCUS.
SENSITIVITY: 1 →2 →...→10
18
LENS SETUP
AF MODE ONESHOT
AF SENSITIVITY 5
AF TIME 10 SEC
ONE. AF TIME OFF
MIN. DIST 1M
ZOOM SPEED FAST
ZOOM LIMIT OFF
EXIT RETURN
All manuals and user guides at all-guides.com

10. OSD MENU STRUCTURE
3. AF TIME
Set AF time. When AF is completed, Focus mode will be Manual.
Even when AF is not completed, it stops when time is up.(unit : sec)
AF TIME: 5 →6 →...→15
4. ONE. AF TIME
Set the ONE.AF TIME. When the user sets the ONE.AF TIME, the ability to automatically
adjust the AF once in that time. (unit :Hour)
ONE. AF TIME: OFF →1 →2 →...→24
5. MIN.DIST
Set the minimum distance which can be focalized.
MIN.DIST: 10cm → 30cm →1m →1.15m →1.3m → 1.5m → 2m →3m → 6m →10m
6. ZOOM SPEED
Set zoom speed slow to fast , 3 steps
ZOOM SPEED: SLOW → MEDIUM → FAST
7. ZOOM LIMIT
Set ZOOM LIMIT.
ZOOM LIMIT: OFF → ON
START ZOOM: Set boundary value of WIDE zooming.
D-ZOOM OFF : START ZOOM X1 ~ X29
D-ZOOM ON : START ZOOM X1 ~ X30
END ZOOM: Set boundary value of TELE zooming.
D-ZOOM OFF: END ZOOM X2 ~ X30
D-ZOOM ON : END ZOOM X2 ~ X300
It sets as the unit of x10 in electronic zoom region.
Since Start Zoom and End Zoom ratio are set, simultaneously Camera
moves to setting magnification. So it enables to adjust in moving to
desired position.
EXIT: After you select a RETURN, IF you press ENTER button then menu-
bar will move to main-menu.
After you select a EXIT, IF you press ENTER button then Updated
data will be saved and exit menu.
19
ZOOM LIMIT SETUP
START ZOOM X1
END ZOOM X30
EXIT RETURN
All manuals and user guides at all-guides.com

20
10. OSD MENU STRUCTURE
• AE SETUP
At Main-menu, select AE SETUP MENU, and press ENTER button.
1. AE MODE
Set AE MODE.
AE MODE function works as following order.
AE MODE: AUTO →IRIS FIX → GAIN FIX → SHUT FIX → MANUAL
AUTO: Exposure is controlled by Shutter Speed, Iris, Gain to meet the Brightness.
You can adjust MAX AGC, MAX DSS, BRIGHTNESS, ZOOM PROP .IRIS
MAX AGC: OFF →2DB → 4DB →… →42DB
MAX DSS: OFF →X2 →X4 →… → X30
BRIGHTNESS: 1 →2 →… →100
ZOOM PROP .IRIS: ON →OFF
IRIS FIX: Iris is fixed, Exposure is controlled automatically by Shutter Speed and Gain.
You can adjust IRIS , MAX AGC , MAX DSS , BRIGHTNESS.
IRIS: F1.6 →F2 →F2.3 →… →F22
MAX AGC: OFF→2DB →4DB →… →42DB
MAX DSS: OFF→X2 →X4 →… →X30
BRIGHTNESS: 1 →2→… →100
GAIN FIX: Gain is fixed, Exposure is controlled by Shutter Speed, and Iris is full open.
You can adjust GAIN , MAX DSS , BRIGHTNESS.
GAIN: OFF →2DB →4DB →… →42DB
MAX DSS: OFF →X2 →X4 →… →X30
BRIGHTNESS: 1 → 2 → … →100
AE SETUP
AE MODE AUTO
BACKLIGHT OFF
DAY / NIGHT DAY
DNR OFF
EXIT RETURN
EXPOSURE SETUP
MODE AUTO
SHUTTER OFF
IRIS
GAIN
MAX AGC 24DB
MAX DSS X10
BRIGHTNESS 25
ZOOM PROP .IRIS ON
EXIT RETURN
All manuals and user guides at all-guides.com