KT&C KPC-LD40NU User manual

HIGH PERFORMANCE
WDR FLAT DOME CAMERA
OPERATION MANUAL
Thank you for choosing our high quality camera.
Before attempting to connect operate this unit, please read and follow these instructions.
M150-LD40LV40-001
VANDAL DOME
PLASTIC DOME

These servicing instructions are for use by qualied service personnel only.
To reduce the risk of electric shock do not perform any servicing other than
that contained in the operating instructions unless you are qualied to do so.
Use Class 2 Power Supply Only
CAUTION
2
CONTENTS
1. CAUTIONS
2. IMPORTANT SAFETY INSTRUCTION
3. EQUIPMENT AND ACCESSORIES
4. CAMERA COMPONENT DESCRIPTIONS
• Plastic Dome / Vandal Dome Type
5. INSTALLATION
• Plastic Dome / Vandal Dome Type
6. DIMENSIONS
• Plastic Dome / Vandal Dome Type
7. SPECIFICATION
8. OSD MANUAL
• Menu structure
• Function Description

1. CAUTIONS
3
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions;
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
Note
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his
own expense.”
WARNING
This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
Caution
Any changes or modications in construction of this devices which are not expressly
approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
1. A regulated DC12V 300mA power supply is recommended for use with
this camera for the best picture and the most stable operation.
An unregulated power supply can cause damage to the camera.
When unregulated power supply is applied, product warranty will be out
of subject.
2. It is recommended that the camera is used with a monitor that has a CCTV
quality 75 video impedance level. If your monitor is switched to high impedance
then please adjust accordingly.
3. Do not attempt to disassemble the camera to gain access to the internal
components. Refer servicing to your dealer.
4. Never face the camera towards the sun or any bright or reective light, which
may cause smear on the picture and possible damage to the CCD.
5. Do not remove the serial sticker for the warranty service.
6. Do not expose the camera to rain or other types of liquid.
7. The apparatus must be connected to a mains socket-outlet with a protective
earthing connection.

1. CAUTIONS
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European
countries with separate collection systems)
This marking shown on the product or its literature, indicate that it should not be
disposed with other household wastes at the end of its working life. To prevent
possible harm to the environment or human health from uncontrolled waste
disposal, please separate this from other types of wastes and recycle it responsibly
to promote the sustainable reuse of material resources.
This product should not be mixed with other commercial wastes purchased this
product, or their local government ofce, for details of where and how they can
take item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of
the purchase contract.
Household users should contact either the retailer where they for disposal.
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER. SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL
4
This symbol is intended to alert the user to the presence of un-
insulated “dangerous voltage” within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of
electric shock to persons.
This symbol is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions
in the literature accompanying the appliance

2. IMPORTANT SAFETY INSTRUCTION
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including ampliers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does not t into your outlet, consult
an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specied by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specied by
the manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to
avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long
periods of time.
14) Refer all servicing to qualied service personnel. Servicing is required when
the apparatus has been damaged in any way, such as power-supply cord or plug
is damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or
has been dropped.
5

3. EQUIPMENT AND ACCESSORIES
Plastic Dome Type Mount Guide (Plastic Dome Type)
Vandal Dome Type Mount Guide (Vandal Dome Type)
Manual
Screws(3ea) / L-Wrench Service Video Output Test Cable / Fixed Tape
6

4. CAMERA COMPONENT DESCRIPTIONS
7
NO PART NAME
1 Top Case
2 Dome Cover
3 Dome Bracket
4 Dome Ass'y
5 Cable
6 Main PCB
7 OSD Controller
8 Bottom Case
1
2
3
4
5
6
8
7
• Plastic Dome Type

4. CAMERA COMPONENT DESCRIPTIONS
8
1
2
3
4
7
6
9
8
5
• Vandal Dome Type
NO PART NAME
1 Top Case
2 Dome Cover
3 Case Rubber
4 Dome Bracket
5 Dome Ass'y
6 Main PCB
7 Safety Wire
8 OSD Controller
9 Bottom Case

5. INSTALLATION(Plastic Dome)
1. Attach the FLAT DOME on the ceiling with using
the screws provided, considering the camera
angle required for the surveillance function.
2. Adjust the LENS ANGLE to the desired
location by hand.
3. Connect the VIDEO OUT CABLE and check the
video image. Change the SETTINGS accordingly
using the OSD controller.
4. After the LENS SETTING is completed,
install the TOP COVER.
9
TAPPING SCREW (4 x 20L) - 3EA
TOP HOUSING
(Assembly direction)
TOP HOUSING
(Separation Direction)
ASSEMBLY HOOK
(2 point)
M4 STAR SCREW
L-WRENCH(T-20)
<TILT ANGLE : 20~90°>
TILT: +90°
TILT: 0°
TILT: +20°
PAN: ±10°
PAN: 0°
<PAN ANGLE : ±10°> * FIXED TAPE: It attached when you install the
product in areas where vibration occurs.
FIXED TAPE attached examples.
SECOND VIDEO CABLE
OSD CONTROLLER
* FIXED TAPE
TILT 45° when attaching TILT 90° when attaching

5. INSTALLATION(Vandal Dome)
1. Attach the FLAT DOME on the ceiling with using the screws
provided, considering the camera angle required for the
surveillance function.
2. Adjust the LENS ANGLE to the desired
ocation by hand.
3. Please remove the protective lm when installing.
4. Connect the VIDEO OUT CABLE and check the video image.
Change the SETTINGS accordingly using the OSD controller.
5. After the LENS SETTING is completed, install the TOP COVER.
10
*CASE RUBBER:
Before assembling the top housing,
Be sure the Rubber correctly positioned.
M4 STAR SCREW
L-WRENCH(T-20)
<TILT ANGLE : 20~90°>
TILT: +90°
TILT: 0°
TILT: +20°
PAN: ±10°
PAN: 0°
<PAN ANGLE : ±10°>
TAPPING SCREW (4 x 20L)-3EA
* FIXED TAPE: It attached when you install the
product in areas where vibration occurs.
FIXED TAPE attached examples.
TILT 45° when attaching TILT 90° when attaching
SECOND VIDEO CABLE
OSD CONTROLLER
* FIXED TAPE
* Protective lm

5. INSTALLATION
• MONITOR CONNECTION
11
When you install the camera, please glue up the end of cable to
keep it stable in order to protect the camera from the humidity problems.
- DC12V/AC24V
- DC12V
CAMERA
BNC FEMALE
DC12V/AC24V
POWER SUPPLY
DC12V/AC24V
(TERMINAL BLOCK)
VIDEO IN
MONITOR
CAMERA
BNC FEMALE
DC12V
(DC JACK)
DC12V ADAPTER
VIDEO IN
MONITOR

6. DIMENSIONS
Unit(mm)
12
119
119
42
134
139
49
• Plastic Dome Type • Vandal Dome Type

7. SPECIFICATION
NTSC PAL
Image Sensor 1/3” 960H SONY Double Scan Super HAD CCD II
Scanning System 2 : 1 Interlace
H Resolution. 750TV Lines
Scanning Frequency 15.734KHz(H), 59.94Hz(V) 15 .625KHz( H) , 50Hz(V)
Total Pixels No. 1028(H) X 508(V) 1028(H) X 596(V)
Effective Pixels No. 976(H) X 494(V) 976(H) X 582(V)
S/N Ratio More than 50dB(AGC OFF, 3DNR ON)
Min. Illumination Color:0.1Lux, BW:0.1Lux ([email protected], AGC 36dB) 0.000001Lux (DSS x256)
Sync System Internal
Gamma r= 0.45
Video Output 1.0 Vp-p Composite(75Ω)
Lens Board Lens
Digital Zoom Ratio 3x
Electronic Shutter 1/60 ~1/100,000sec 1/50 ~1/100,000sec
Digital Slow Shutter OFF, 2 ~ 256 Field
Flickerless ON / OFF
WDR ON / OFF (Level adjustable)
BLC ON / OFF (Level adjustment, Area selection)
HLC ON / AUTO / OFF (Level adjustable)
AGC OFF, 6 ~ 36dB
DNR(2D/3D) ON / OFF (Level adjustable)
Image Function Image reverse(Normal/Flip), Freeze, Contrast, Sharpness
Day & Night COLOR / BW / AUTO(DIGITAL D/N)
Motion Detection 4 Zones (Level adjustable, Area adjustment)
Privacy Masking 15 Zones (Area adjustment)
White Balance ATW / PUSH / USER1 / USER2 / ANTI CR /
MANUAL / PUSH-LOCK
OSD Built in (Joystick)
Language ENGLISH / JAPANESE / GERMAN / FRENCH /
RUSSIAN / PORTUGUESE / SPANISH / CHINESE
Operating Temperature 14°F~122°F(-10°C~+50°C)
Storage Temperature -4°F~140°F(-20°C~+60°C)
Humidity Less than 80%
Weight PLASTIC DOME Type: Approx. 200g
VANDAL DOME Type: Approx. 500g
Power
Consumption
DC DC12V (±10%), Max. 140mA
DUAL DC12V (±10%), Max. 190mA
AC24V (±10%), Max. 2.5W
Dimension (mm) PLASTIC DOME Type: 119mm x 119mm x 42mm
VANDAL DOME Type: 139mm x 134mm x 49mm
Specications and designs are subject to change for improving the
functionality of this product without notice.
13

8. OSD MANUAL
• Menu structure
Main MENU 1st Sub MENU 2nd Sub MENU 3rd Sub MENU 4th Sub MENU 5th Sub MENU
EXPOSURE
AUTO
HIGH LUMINANCE FLICKERLESS OFF / ON
BRIGHTNESS 0 ~ 255
LOW LUMINANCE
MODE AGC, SLOW, AGC > SLOW, SLOW >
AGC, OFF
AGC MAX 6, 12, 18, 24, 30, 36
DSS MAX 2, 4, 8, 16, 32, 64, 128, 256
BRIGHTNESS x0.25, x0.5, x0.75, x1.0
RETURN
MANUAL
MODE SHUT, SLOW
SHUT
MODE (SHUT) ONLY
1/50(PAL), 1/60(NTSC), 1/100(NTSC), 1/120(PAL),
1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000
MODE (SLOW) ONLY 2, 4, 8, 16, 32, 64, 128, 256
AGC 6, 12, 18, 24, 30, 36, 42, 44.8
RETURN
WHITE
BALANCE
ATW
SPEED 0 ~ 255
DELAY CNT 0 ~ 255
ATW FRAME x0.5, x1.0, x1.5, x2.0
ENVIRONMENT INDOOR, OUTDOOR
RETURN
PUSH
USER1
B-GAIN 0 ~ 255
R-GAIN 0 ~ 255
RETURN
USER2
B-GAIN 0 ~ 255
R-GAIN 0 ~ 255
RETURN
ANTI CR
MANUAL
LEVEL UP PUSH ENTER
LEVEL DOWN PUSH ENTER
PRESET
RETURN
PUSH LOCK
DAY&NIGHT
COLOR
AUTO
BURST OFF, ON
DELAY CNT 0 ~ 255
DAY > NIGHT 0 ~ 255
NIGHT > DAY 0 ~ 255
RETURN
BW BURST OFF, ON
RETURN
14

8. OSD MANUAL
Main MENU 1st Sub MENU 2nd Sub MENU 3rd Sub MENU 4th Sub MENU 5th Sub MENU
WDR/BLC
WDR MODE OFF, ON
LEVEL 0 ~ 15
CONTRAST1 0 ~ 7
CONTRAST2 0 ~ 4
RETURN
BLC MODE OFF, ON
ZONE CENTER, TOP, BOTTOM,
LEFT, RIGHT
LEVEL 0 ~ 15
RETURN
HLC MODE OFF, ON, AUTO
CLIP LEVEL 0 ~ 255
SCALE 0 ~ 15
RETURN
DNR
2DNR MODE OFF, ON
2DNR LEVEL 0 ~ 15
3DNR MODE OFF, ON
3DNR LEVEL 0 ~ 63
RETURN
IMAGE
HV-FLIP OFF, ON
FREEZE OFF, ON
EZOOM 1.0x ~ 3.0x
CONTRAST 0 ~ 63
SHARPNESS 0 ~ 15
RETURN
SPECIAL
CAMERA TITLE OFF, ON DISPLAY THE TITLE EDITING MENU
RETURN
LANGUAGE ENGLISH / 中文 / Р у с с к и й / ESPAÑOL / DEUTSCH / FRANCAIS /
PORTUGUÊS / 日本語
PRIVACY
AREA SEL 1/15 ~ 15/15
MODE OFF, ON
POSITION NEXT: PUSH ENTER
COLOR "WHITE, BLACK, RED, GREEN, BLUE,
YELLOW, CYAN, MAGENTA"
TRANSP 0.00, 0.50, 0.75, 1.00
MOSAIC OFF, ON
RETURN
MOTION DET OFF, ON
DETECT SENSE 0 ~ 127
BLOCK DISP OFF, ON
MONITOR AREA
AREA SEL 1/4 ~ 4/4
MODE OFF, ON
TOP 0 ~ 15
BOTTOM 0 ~ 15
LEFT 0 ~ 23
RIGHT 0 ~ 23
RETURN
FACTORY
DEFAULT
EXIT
SAVE&EXIT
15