KT&C KPC-N850 User manual

Super Night Vision Camera
OPERATION MANUAL
Thank you for choosing our high quality camera.
Before attempting to connect or operate, please read and follow
these instructions.
M080-Night-003
Illuminator Kit Type

CONTENTS
1. CAUTIONS
2. FEATURES
3. COMPONENTS
4. NAME AND FUNCTION
5. INSTALLATION
6. DIMENSIONS
7. SPECIFICATION
8. OSD MANUAL
9. COMMUNICATION PROTOCOL
3

1. CAUTIONS
4
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions;
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
1. A regulated DC12V 3A power supply is recommended for use with this camera
for the best picture and the most stable operation.
An unregulated power supply can cause damage to the camera.
When unregulated power supply is applied, product warranty will be
out of subject.
2. It is recommended that the camera is used with a monitor that has a CCTV quality
75 video impedance level.
If your monitor is switched to high impedance then please adjust accordingly.
3. Do not attempt to disassemble the camera to gain access to the internal componets.
Refer servicing to your dealer.
4. Never face the camera towards the sun or any bright or reective light, which may
cause smear on the picture and possible damage to the CCD.
5. Do not remove the serial sticker for the warranty service.
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.”
Note-
Any changes or modifications in construction of this device
which are not expressly approved by the party responsible
for compliance could void the user’s authority to operate the
equipment.
Caution -
This is a class A product. In a domestic environment this product
may cause radio interference in which case the user may be
required to take adequate measures.
WARNING -

1. CAUTIONS
5
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with
separate collection systems)
This marking shown on the product or its literature, indicate that it should not
be disposed with other household wastes at the end of its working life. To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
This product should not be mixed with other commercial wastes purchased this
product, or their local government ofce, for details of where and how they can
take item for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract.
Household users should contact either the retailer where they for disposal.

2. FEATURES
• 1/3" 410K/470K Sony Super-HAD CCDⅡ
Minimum illumination
- 0.00001 Lux(F1.2, 30 IRE, Sense-Up X256, AGC high)
- LED Mode: 0 Lux ( IR LED On) S/N Ratio 50 dB
• High Resolution 600TV Lines
This camera has realized high resolution of 600TV lines using the top-notch full
digital image processing, 10 Bit A/D serial signal processing and special algorithm
technologies.
• 3D DNR (3D Digital Noise Reduction)
The DNR technology eliminates noise thus generating a distinct and clear image.
This camera DNR function utilizes an adaptive 3D Filter reducing noise caused by
movement.
• DAY&NIGHT
This camera has the Day&Night function.
Day&Night operation feature an ‘auto’ mode which switches between day and night
mode automatically based upon the level of illumination on the scene.
And also, the COLOR mode operates in daytime conditions to provide optimum colors,
and B/W mode operates in night-time conditions to enhance the denition of the
image.
• Privacy Mask Function
Privacy masking allows for the ‘blanking’ of specic areas of a scene, where the viewing
or recording of images is prohibited or undesired.
• OSD (On Screen Display)
This camera can easily controlled by multi-language OSD function on the monitor
screen.
• AIR-Circulation system
- Operation : Turns on with the IR LEDs.
- Diagram :
6

3. COMPONENTS
Standard
DSP COLOR CAMERA
VIDEO OUTPUT TEST CABLE SCREW / L-WRENCH
OPERATION MANUAL
Option
ILLUMINATOR
SUPPORTER
SCREW / L-WRENCH CABLE
7

8
4. NAME AND FUNCTION
• Standard Type
• Illuminator Kit Type
① Sunshield
② Mounting Bracket
③ Photo cell
④ External Zoom and Focus adjustment
⑤ Body
⑥ Body Fixing Ring
⑦ Supporter
⑧ IR Illuminator(each 140ea IR LED)
⑨ Function Explanation
Pressing the “SETUP” button prompts the main setup menu.
“PUSH” button : To access the main setup menu
“U” button : Menu item UP selection
“D” button : Menu item DOWN selection
“L” button : To change data to down
“R” button : To change data to up
LED Level : LED Volume – Adjusting brightness of the LED
(Initial Setting Level :Max , Camera part Only)
⑦ ⑧⑧⑧
①②②
③
④⑤⑥
⑨

9
5. INSTALLATION
• Illuminator Kit
* Explanation
1. A : Service Video Connector.
2. B : Illuminator Combination Connector.
3. C : Illuminator Connector.

10
5. INSTALLATION
• MONITOR CONNECTION
(1) DC12V
(2) DUAL(AC24V/DC12V)
When you install the camera, please glue up the end of cable to
keep it stable in order to protect the camera from the humidity problems.
DUAL(AC24V/DC12V)
POWER SUPPLY

6. ADJUSTMENT
* 1st Axis
90°
* 2nd Axis
360°
* 3rd Axis
360°
125°
* Illuminator kit combinations
11

7. DIMENSIONS
• Standard Type
• Illuminator Kit Type
Unit(mm)
12
ø110
115.2
317
131.4
171.5
185.8
270
314.8
ø110
111.7
89.5
185.8
131.4
171.5
317
102
55.3
270
222

13
8. SPECIFICATION
Signal Format NTSC PAL
CCD
Image Device 1/3" Sony Super HAD CCDⅡ
Total Pixels 811(H) x 508(V) 795(H) x 596(V)
Effective Pixels 768(H) x 494(V) 752(H) x 582(V)
Sync. Scanning Frequency H: 15.734 KHz, V:59.94 Hz H: 15.625 KHz, V:50 Hz
Performance
H.Resolution 600TV Lines
Minimum illumination 0 Lux (IR LED ON)
S/N Ratio More than 50dB(AGC Off)
Gamma γ= 0.05 ~1.0 Adjustable / USER
Sync System Internal
Video Output 1 [Vp-p] Composite 75Ω unbalanced
OSD Display Available
Functions
Iris Control DC
Electronic Shutter 1/60 ~ 1/100.000 sec 1/50 ~ 1/100.000 sec
Sense-up X2 ~ X256
Gain Control Off / Low / Middle / High
BLC Off / BLC / HSBLC
Wh i t e Ba l a nce ATW / PUSH / PUSH-LOCK / MANUAL / Indoor / Outdoor
3D N R Off / On (level setting)
Sh a r pne s s Adjustable
Motion Detection Available
Privacy Masking 8 Zone
Digital Zoom Off / On(Max x32)
Language Standard : English, French, Russian, German, Spanish, Dutch
Option1: English, Chinese / Option2:English , Japanese
Power
Consumption
DC 12V DC 12V ±10% Max 1.5A
DC 12V ±10% Max 3A (With Illuminators Combination)
DUAL
AC24V AC 24V ±10% Max 24W
AC 24V ±10% Max 2A (With Illuminators Combination)
DC12V DC 12V ±10% Max 1.5A
DC 12V ±10% Max 3A (With Illuminators Combination)
IR LED 100 Units Infra LED
240 Units IR LED (With Illuminators Combination)
IR LED Wavelength 850 nm
Dip switch function Joystick , LED Brightness Control volume
Lens Mount 5-50mm DC Drive Vari-focal lens(ICR)
Option Heater, Illuminators Kit
Water Resistant Weather Proof(IP65)
Dimension 115.2 x171.6 x307.8 (with sunshield)
315 x177.5 x307.8 (with Illuminators)
Operating temperature -10℃~ +50℃
Storage temperature -20℃~ +60℃
Operating Humidity 10% ~ 60%

14
9. OSD MANUAL
GENERAL STRUCTURE
SETUP MENU
LENS •BRIGHTNESS •RETURN
EXPOSURE •SHUTTER •AGC
•SENSE-UP •BLC •D-WDR
•RETURN
WHITE BAL •ATW •PUSH •PUSH-LOCK
•MANUAL •INDOOR •OUTDOOR
DAY&NIGHT •COLOR •B/W •AUTO
IMAGE •FREEZE •MIRROR •D-ZOOM
•SHARPNESS •COLOR GAIN
•GAMMA •NEG.IMAGE •RETURN
3DNR •LEVEL •RETURN
SPECIAL •CAM TITLE •LANGUAGE •MOTION
•PRIVACY •SYNC •RETURN
RESET -
EXIT -

15
9. OSD MANUAL
LENS MENU STRUCTURE
EXPOSURE MENU STRUCTURE
LENS →DC →BRIGHTNESS →1~100
↕
EXPOSURE
↕
WHITE BAL
↕
DAY NIGHT
↕
IMAGE
↕
3DNR
↕
SPECIAL
↕
RESET
↕
EXIT
LENS SHUTTER →X256 ~1/100K
↕ ↕
EXPOSURE →AGC →LOW, MIDDLE, HIGH
↕ ↕
WHITE BAL SENSE-UP →X2 ~ X256
↕ ↕ GAIN, LEFT/RIGHT, WIDTH,
TOP/BOTTOM, HEIGNT
DAY NIGHT BLC →BLC →
↕ ↕
IMAGE ↕HSBLC →LEVEL, LEFT/RIGHT, WIDTH,
TOP/BOTTOM, HEIGNT
↕
3DNR D-WDR →INDOOR, OUTDOOR
↕
SPECIAL
↕
RESET
↕
EXIT

16
9. OSD MANUAL
WHITE BALANCE MENU STRUCTURE
DAY & NIGHT MENU STRUCTURE
LENS
↕
EXPOSURE
↕
WHITE BAL →ATW
↕ ↕
DAY NIGHT PUSH
↕ ↕
IMAGE P-LOCK
↕ ↕
3DNR MANUAL →BLUE 1~ 100
↕ ↕ ↕
SPECIAL INDOOR RED 1~ 100
↕ ↕
RESET OUTDOOR
↕
EXIT
LENS
↕
EXPOSURE
↕
WHITE BAL
↕
DAY NIGHT →AUTO →D&N LEVEL →0~ 3
↕ ↕
IMAGE B/W →BURST →ON / OFF
↕ ↕
3DNR COLOR
↕
SPECIAL
↕
RESET
↕
EXIT

17
9. OSD MANUAL
IMAGE MENU STRUCTURE
3DNR MENU STRUCTURE
LENS
↕
EXPOSURE
↕
WHITE BAL FREEZE →OFF →ON
↕
DAY NIGHT MIRROR →MIRROR →V-FLIP →ROATE →OFF
↕ ↕
IMAGE →D-ZOOM →x1 ~ x32 →PAN -100~100 →TILT -100~100
↕ ↕
3DNR SHARPNESS →0 ~ 31
↕
SPECIAL COLOR GAIN →BLUE 1 ~100 →RED 1 ~100
↕ ↕
RESET GAMMA →0.05~1
↕ ↕
EXIT NEG.IMAGE →OFF →ON
LENS
↕
EXPOSURE
↕
WHITE BAL
↕
DAY NIGHT
↕
IMAGE
↕
3DNR →ON →LEVEL →1~100
↕ ↕
SPECIAL OFF
↕
RESET
↕
EXIT

18
9. OSD MANUAL
SPECIAL MENU STRUCTURE
RESET MENU STRUCTURE
LENS
↕
EXPOSURE
↕
WHITE BAL
↕
DAY NIGHT
↕
IMAGE
↕
3DNR
↕
SPECIAL
↕
RESET →FACTORY RESET
↕
EXIT
LENS
↕
EXPOSURE
↕
WHITE BAL CAM TITLE →ON / OFF ↔POSITION CONTROL
↕
↕
DAY NIGHT LANGUAGE →ENGLISH ↔FRENCH ↔RUSSIAN
↔
GRRMAN ↔
DEUTSCH
↔DUTCH
↕
IMAGE ON/
OFF
AREA
SEL
AREA
DISPLAY
LEFT/
RIGHT WIDTH TOP/ BOTTOM
↕MOTION → ↔ ↔ ↔ ↔ ↔
3DNR ↕
↕
AREA1~4 ON/OFF MOTION
VIEW ↔SENSITIVITY ↔HEIGHT
SPECIAL →PRIVACY →AREASEL ↔AREADISPLAY ↔LEFT/RIGHT ↔WIDTH ↔TOP/BOTTOM
↕ ↓ ↓ ↕
RESET AREA1~8 ON/OFF COLOR ↔HEIGHT
↕
EXIT SYNC →INT

19
9. OSD MANUAL
OSD FUNCTION DESCRIPTION
1.LENS
- DC LEVEL
BRIGHTNESS : Enable user to select the DC level for Brightness of image(1~100).
2. EXPOSURE
: Enable user to set up the function of SHUTTER, AGC.
- SHUTTER
• FLK : Enable user to set up the FLICKERLESS.(NTSC: 1/100, PAL: 1/120)
• FIXED : Enable user to set up the Shutter Speed.
> 1/60(50), 1/250, 1/500, 1/2K, 1/5K, 1/10K, 1/100K.
* ( ) is for PAL TYPE.
- BRIGHTNESS : Enable user to set up the MANUAL electronic Shutter value.
- AGC : Enable user to make imager bright to amplify the Gain.
- SENSE-UP : Low-speed shutter control.
- BLC : The Function of Back Light Compensation.
• HSBLC : Highlight Suppression BLC will darken image portions for clearer images.
- D-WDR : Allows every detail to be captured accurately
even if one portion is bright while other portions are dark.
LENS
BRIGHTNESS 60
RETURN RET┛
EXPOSURE
SHUTTER 1/60
AGC MIDDLE
SENSE-UP OFF
BLC OFF
D-WDR OFF
RETURN RET┛

20
9. OSD MANUAL
3. WHITE BALANCE
: Enable user to represent the accurate white color by controlling the R.G.B level.
• ATW : Enable user to trace the White Balance automatically in the Wide range
(2,500K ~ 9,500K)
• PUSH : Enable user to trace the White Balance automatically in all the range.
• P-LOCK : Enable user to set up automatically readjusted only at the request
of the user.
• MANUAL : Enable user to set the RED GAIN or BLUE GAIN.
• INDOOR : Enable user to set up 3,200K base mode.
• OUTDOOR : Enable user to set up 5,400K base mode
4. DAY&NIGHT
: Conversion of output image COLOR/BW depending on exterior environment.
- AUTO : Color or B/W mode auto change Select to detect mode as level of VIDEO.
• DWELL TIME : Time to protect susceptible conversion of COLOR/BW (0~10 SEC).
• D>N LEVEL : Turnover level from COLOR(Day) to BW(Night).
• N>D LEVEL : Turnover level from BW(Night) to COLOR(Day).
- B/W : Enable user to x the output image in B/W.
• BURST ON/OFF : Select the burst signal ON/OFF when Night condition.
- COLOR : Enable user to x the output image in COLOR.
- EXTERNAL : Enable user to convert to COLOR/BW by signal of the external input.
WHITE BAL MANUAL
BLUE 24
RED 32
RETURN RET┛
DAY NIGHT AUTO
DWELL TIME 10sec
D>N LEVEL 4
N>D LEVEL 6
RETURN RET┛

21
9. OSD MANUAL
5. IMAGE
: Setting up the FREEZE, MIRROR, D-ZOOM, SHARPNESS, COLOR GAIN,
GAMMA, NEGATIVE IMAGE.
- FREEZE : Setting of moving images in freeze-frame mode
- MIRROR
• MIRROR : Enable user to set up reversed LEFT and RIGHT image
• V-FLIP : Enable user to set up vertically ipped video.
• ROTATION : Enable user to set up 180-degree rotation lp function.
- D-ZOOM : Enable user to expand one part of the monitor screen for viewing.
- SHARPNESS : Enable user to set up sharpness control.
- COLOR GAIN : Enable user to set the RED GAIN or BLUE GAIN.
- GAMMA : Enable user to set up compensation according to gamma value.
- NEG.IMAGE : Enable user to set up negative image ON/OFF.
6. 3DNR
: three-dimensional noise reduction
- LEVEL : Enable user to set up noise reduction level.
IMAGE
FREEZE OFF
MIRROR OFF
D-ZOOM ON┛
SHARPNESS 5
COLOR GAIN ┛
GAMMA 0.45
NEG.IMAGE OFF
RETURN RET┛
3DNR
LEVEL 50
RETURN RET┛