KT&C KNC-p3TR3XIR User guide

1
KNC-p3TR3XIR
KNC-p3TR4XIR
KNC-p3TR6XIR
3 Megapixel Plug & Play Capable
IP66 EXIR IP Turret Cameras
Quick Operation Guide

KNC-p3TR_XIR IP Turret Camera·Quick Operation Guide
1
1
Thank you for selecting this KT&C Omni IP Series product. For
additional information please refer to the complete User Guide for
this cameras series. End users should contact their KT&C Certified
Dealer for service. Certified Dealers can obtain support directly from
KT&C.
About This Guide
While KT&C makes every effort to insure the completeness and
accuracy of the information contained in this Guide, we are not
responsible for typographical errors or misprints. At the same time,
KT&C reserves the right to make changes to improve the performance
of our products at any time without notice, and so the specifications
and content of this document are subject to change without notice.
Every effort will be made to include updates in new versions of this
manual and/or online.
DISCLAIMER STATEMENT
“Underwriters Laboratories Inc. (“UL”) has not tested the
performance or reliability of the security or signaling aspects of this
product. UL has only tested for fire, shock or casualty hazards as
outlined in UL’s Standard(s) for Safety, UL60950-1. UL Certification
does not cover the performance or reliability of the security or
signaling aspects of this product. UL MAKES NO REPRESENTATIONS,
WARRANTIES OR CERTIFICATIONS WHATSOEVER REGARDING THE
PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING
RELATED FUNCTIONS OF THIS PRODUCT.

KNC-p3TR_XIR IP Turret Camera·Quick Operation Guide
2
2
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to
comply with the limits for a digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own
expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied
accessories too are marked with "CE" and comply
therefore with the applicable harmonized European
standards listed under the Low Voltage Directive 2006/95/EC, the
EMC Directive 2004/108/EC, the RoHS Directive 2011/65/EU.

KNC-p3TR_XIR IP Turret Camera·Quick Operation Guide
3
3
2012/19/EU (WEEE directive): Products marked with
this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper
recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or
dispose of it at designated collection points. For more information
see: www.recyclethis.info.
2006/66/EC (battery directive): This product
contains a battery that cannot be disposed of as
unsorted municipal waste in the European Union.
See the product documentation for specific battery
information. The battery is marked with this symbol,
which may include lettering to indicate cadmium (Cd), lead (Pb), or
mercury (Hg). For proper recycling, return the battery to your supplier
or to a designated collection point. For more information see:
www.recyclethis.info

KNC-p3TR_XIR IP Turret Camera ·Quick Operation Guide
4
4
Safety Instructions
These instructions are intended to ensure that the camera is installed
in a manner that avoids danger to persons or property loss.
These precautionary measures are divided into “Warnings” and
“Cautions”
Warnings: Serious injury or death may occur if any of the warnings
are neglected.
Cautions: Injury or equipment/property damage may occur if any of
the cautions are neglected.
Warnings
●In the use of the product, you must be in strict compliance with
the electrical safety regulations of the nation and region. Please
refer to technical specifications for detailed information.
●Input voltage should meet the requirements for both the SELV
(Safety Extra Low Voltage) and Limited Power Source for 12 VDC
Warnings Follow these
safeguards to prevent
serious injury or death.
Cautions Follow these
precautions to prevent
potential injury or material
damage.

KNC-p3TR_XIR IP Turret Camera ·Quick Operation Guide
5
5
according to the IEC60950-1 standard; or 802.3af PoE. Please
refer to technical specifications for detailed information.
●If connecting several devices to one power supply, to avoid any
overload that may cause over-heating or a fire hazard insure that
the power supply is adequate for the power load.
●Please make sure that all plugs are firmly connected to the
power sockets. When the product is mounted on wall or ceiling,
the device shall be firmly attached, taking into consideration any
wind, snow loading, or other factors. The mounting surface shall
be capable of supporting several times the base weight of the
camera.
●If smoke, unusual odors or noise come from the device, turn off
the power at once and unplug the power cable, and then
contact authorized service personnel.
Cautions
●Make sure the power supply voltage is correct before using the
camera.
●Do not drop the camera or subject it to physical shock.
●Do not touch lenses or sensor modules with fingers. If cleaning is
necessary, use clean cloth with a bit of ethanol and wipe gently.
If the camera will not be used for an extended period, please
protect the lens openings from damage and/or debris.
●Avoid aiming the camera at the sun or extremely bright light
sources. Blooming or smearing may occur in excessive light

KNC-p3TR_XIR IP Turret Camera ·Quick Operation Guide
6
6
(which is not a malfunction), and could compromise the
performance of the sensor.
●The sensor may be damaged if exposed to laser energy, so when
any laser equipment is in use, make sure that the sensor will not
be exposed to the laser beam.
●Do not place the camera in extremely hot or cold (see camera
specifications) locations. Do not exceed the rated environmental
(IP66) conditions. Do not expose the camera to high levels of
electromagnetic (RF) radiation.
●To avoid heat accumulation, good ventilation is required in the
operating environment.
●Keep the camera away from solvents while in use; exposure to
liquids should not exceed IP66 environmental conditions.
●During shipping, the camera shall be packed in its original
packing, or packing providing the equivalent protection.
●Improper use or replacement of any batteries (if so equipped)
may result in the hazard of explosion. Replace with the same or
equivalent type only. Dispose of used batteries according to the
instructions provided by the battery manufacturer.
●If the product does not function properly, Dealers please contact
KT&C; End Users please contact your KT&C Certified Dealer or an
authorized service center. Do not disassemble the camera for
repair or maintenance by yourself. (KT&C shall not assume any
responsibility for problems caused by unauthorized repair or
maintenance.)

KNC-p3TR_XIR IP Turret Camera ·Quick Operation Guide
7
77
Table of Contents
1 Appearance and Description .......................................................... 8
2 Installation.................................................................................... 10
3 Setting the Network Camera over the LAN ......Error! Bookmark not
defined.
4 Accessing via Web Browser ................ Error! Bookmark not defined.

KNC-p3TR_XIR IP Turret Camera ·Quick Operation Guide
8
88
1Appearance and Description
Figure 1-1 Overview
Table 1-1 Description
NO.
Description
1
10M/100M self-adaptive Ethernet interface
2
Power Cable
3
Trim Ring

KNC-p3TR_XIR IP Turret Camera ·Quick Operation Guide
9
99
NO.
Description
4
Lens
5
IR LED
6
Enclosure
7
Dome Drive
Please make sure that the power adapter is compatible with the
camera. This series of camera supports Power over Ethernet (PoE),
and the standard power supply is 12 VDC.

KNC-p3TR_XIR IP Turret Camera ·Quick Operation Guide
10
1010
2Installation
Before you start:
Make sure the camera is in good condition and all the accessory
parts are included.
Make sure all related equipment is powered-off during the
installation.
Check to insure that the specifications of the camera are correct
for the installation environment.
Make sure the power supply voltage is 12VDC or PoE compliant to
avoid damage to the camera.
If the product does not function properly, Dealers please contact
KT&C; End Users please contact your KT&C Certified Dealer or an
authorized service center. Do not disassemble the camera for
repair or maintenance by yourself.
Make sure that the mounting surface is strong enough to withstand
three times the weight of the camera.
If the IR LEDS in this camera will be active, you must observe the
following precautions to prevent IR reflection:
●Dust or grease on the lens/dome cover will cause IR reflection.
Please do not remove the cover protective film until the
installation is finished. If there is dust or grease on the
lens/dome cover, clean the lens/dome cover with clean soft
cloth and isopropyl alcohol.

KNC-p3TR_XIR IP Turret Camera ·Quick Operation Guide
11
1111
●Make sure that there is no reflective surface too close to the
camera lens. The IR light from the camera may reflect back into
the lens causing haze, distortion or improper scene exposure.
●Any foam ring around the lens must be seated flush against the
inner surface of the cover/bubble to isolate the lens from the IR
LEDS. Fasten the lens/dome cover to camera body so that the
foam ring and the dome cover are attached seamlessly.
Steps:
1. Rotate the trim ring counterclockwise to remove it from the
camera.
Figure 2-1 Dissemble the Camera
Trim Ring
Camera
Module

KNC-p3TR_XIR IP Turret Camera ·Quick Operation Guide
12
1212
2. Drill the screw holes and the cable hole on the wall or ceiling
according to the drill template.
Figure 2-2 The Drill Template
There are two cable outlet methods. One is to route the cables
through the cable hole, and the other is to route the cables through
the side outlet shown below.
Figure 2-3 Side Outlet

KNC-p3TR_XIR IP Turret Camera ·Quick Operation Guide
13
1313
Three side outlets on the enclosure are available, which makes
routing the cables easier if surface wiring will be used. Use a plier to
remove the plastic where it covers the wire outlet, and route the
cables through the hole.
3. Connect the corresponding power/network cables.
4. Attach the camera to the wall or ceiling with the supplied screws
and expansion anchors if needed. Be surer the surface can
support at least 3 times the weight of the camera.
Figure 2-4 Secure the Camera to the Ceiling
5. Adjust the direction:
1). Loosen the lock screw.

KNC-p3TR_XIR IP Turret Camera ·Quick Operation Guide
14
1414
2). Rotate the camera module to adjust the pan angle and the
tilt angle.
3). Tighten the lock screw to fix the desired surveillance angle.
Figure 2-5 Lock Screw
Figure 2-6 Adjust the Direction
Lock Screw

KNC-p3TR_XIR IP Turret Camera ·Quick Operation Guide
15
1515
6. Attach the trim ring to the camera and rotate the trim ring
clockwise secure it.
Figure 2-7 Replace the Trim Ring
Figure 2-8 Completed Installation

KNC-p3TR_XIR IP Turret Camera ·Quick Operation Guide
0
00
3Setting the Camera Parameters over
the LAN
Purpose:
To view and configure the camera via a LAN, you need to connect the
network camera in the same subnet with your computer, and install
the OMNI Finder or OMNI CMS software to search and change the IP
of the network camera.
The following figure shows a camera and PC connected through a
switch:
Figure 3-1 Typical LAN Connection
Set the IP address of the camera for accessing via LAN.
Steps:
1. To get the IP address, you can choose either of the following
methods:
Use OMNI Finder, a software tool which can automatically detect
network camera on the LAN and list device information such as IP
address, subnet mask, port number, device serial number, device
version, etc., as shown in Figure 3.2 below.

KNC-p3TR_XIR IP Turret Camera ·Quick Operation Guide
1
11
Use OMNI CMS software and to list the online devices. Please
refer to the user manual for the OMNI CMS software for detailed
information.
2. Change the IP address and subnet mask to the same subnet as
that of your computer, or change your computer to match the
address/subnet of the camera.
Refer to the following introductions to set IP address with OMNI
Finder software:
Search active devices online
Search online devices automatically:
After launching the OMNI Finder software, it automatically
searches for online devices every 15 seconds on the subnet
where your computer is connected. It displays the total
number and information of the discovered devices in the
Online Devices interface. Device information including the
device type, IP address, port number, gateway, etc. will be
displayed.

KNC-p3TR_XIR IP Turret Camera ·Quick Operation Guide
2
22
Figure 3-2 Search Online Devices
Devices can be discovered and displayed in the list in 15
seconds after they go online; devices will be removed from
the list in 45 seconds after going offline.
Search online devices manually:

KNC-p3TR_XIR IP Turret Camera ·Quick Operation Guide
3
33
You can also click to refresh the online device
list manually. The newly searched devices will be added to the
list.
You can click or on each column heading to order
the information; you can click to show the device table
and hide the network parameter panel on the right side, or
click to show the network parameter panel.
1.2 Modify device information
Steps:
1) Select the device to be modified in the device list as shown
in Figure 3-3. The network parameters of the device will be
displayed in the Modify Network Parameters panel on the
right side as shown in Figure 3-4.
2) Edit the modifiable network parameters, e.g. IP address,
subnet, port number and gateway. NOTE: This port if the
CONTROL port used by the Finer and CMS. It is NOT the
HTTP web browsing port (which defaults to 80).
3) Enter the password of the admin account of the device in
the Password field and click Save to save the changes.