KT&C KPC-VDN101 User manual

Thank you for choosing our high quality camera.
Before attempting to connect or operate, please read and follow
these instructions.
OPERATION MANUAL
HIGH RESOLUTION
ARMORED DOME CAMERA
M063-VDN101-002

CONTENTS
1. Cautions
2. Features
3. Package
4. Overview and function
5. Installation
6. Connection
7. Dimensions
8. Specifications
9. Setup menu operation
• SETUP MENU
• SETUP MODE
• CAMERA ID
• LENS
• SHUTTER
• WHITE BALANCE
• LANGUAGE MODE SETUP
• RESET
10.Function Menu operation
• FUNCTION MENU
• BLC
• AGC
• DAY&NIGHT
• PRIVACY
• MIRROR
• GAMMA
• MOTION
11.Troubleshooting
3

1.Cautions
4
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions;
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Note -
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio / tv technician for help.
Any changes or modications in construction of this device
which are not expressly approved by the party responsible
for compliance could void the user's authority to operate the
equipment.
Caution -
1. A regulated DC12V 1.5A power supply is recommended for use with this camera
for the best picture and the most stable operation.
An unregulated power supply can cause damage to the camera.
When unregulated power supply is applied, product warranty will be
out of subject.
2. It is recommended that the camera is used with a monitor that has a CCTV quality
75 video impedance level.
If your monitor is switched to high impedance then please adjust accordingly.
3. Do not attempt to disassemble the camera to gain access to the internal
components. Refer servicing to your dealer.
4. Never face the camera towards the sun or any bright or reective light, which may
cause smear on the picture and possible damage to the CCD.
5. Do not remove the serial sticker for the warranty service.

Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with
separate collection systems)
This marking shown on the product or its literature, indicate that it should not
be disposed with other household wastes at the end of its working life. To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
This product should not be mixed with other commercial wastes purchased this
product, or their local government ofce, for details of where and how they can
take item for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract.
Household users should contact either the retailer where they for disposal.
1.Cautions
5

CAUTIONS
1
2.Features
6 7
• Sony 1/3” Super HAD CCDⅡ
• 550TV Lines
• OSD Function
• Manual shutter
• Privacy Zone
• Dual Voltage use DC12V/AC24V
• Motion Detection
• 3-Axis Gimbal
The Se rvic e Vide o Conn ecto r also p rovi des th e inst all er wit h an
easy way of configuring the camera.
• Service Video connector
Pan Rotation Horizontal RotationTilt Rotation
CAUTION panning the bracket in excess of 3 rotations in one direction may
cause damage to the cable.

6 7
FEATURES
2
CAUTIONS
1
3. Package
1 ARMORED DOME CAMERA
2 SURFACE MOUNT
3 VIDEO OUTPUT TEST CABLE
4 OPERATION MANUAL
5
SCREW(M4x10) - 4ea
SCREW(5x30) - 4ea
SCREW(M4x40.SUS) - 4ea
L WRENCH - T20
6 MOUNT GUIDE

4.Overview and function
• CONTROL FUNCTION
(OSD JOYSTICK)
LEFT
UP
RIGHT
DOWN
MENU
• Name (LED Type)
• Name (Standard)
8 9

5. Installation
Standard TypeLED Type
8 9
Mount Guide

5. Installation
10
1. Installation of Flush Mount
2. Installation of Surface Mount
PIPE
PIPE
① Installation of the camera with SURFACE
CASE(using M4x40)
② Installation of the camera with SCREWS
③ Installation of the camera with JUNCTION BOX
① Installation of the camera on the wall
② Installation of the camera on the 3/4” NPT PIPE
③ Installation of the camera on the JUNCTION BOX
Check the safe wire which
should be entirely inserted into camera
housing during locking the dome cover to
maintain Waterproof condition.
When using the camera
without LED take off the rubber.
NOTE

6.Connection
11
When you install the camera, please glue up the end of cable to
keep it stable in order to protect the camera from the humidity problems.
• DUAL(DC 12V/AC24V)
• DC 12V

7.Dimensions
Unit : mm
45
˚
70
˚
Standard Type LED Type
12
When you x the focus around 22.0mm in f9.0-22.0mm Varifocal lens, please
set short distance focus approximately 3M and do not set long distance focus
Surface Mount Type
Flush Mount Type
Type A Type B

8.Specifications
Signal Format NTSC PAL
Image Device 1/3" Sony Super HAD CCDⅡ
Scanning System 2:1 Interlace
H.Resolution 550TV Lines
Scanning Frequency H:15.734KHz, V:59.94Hz H:15.625KHz, V:50Hz
Total Pixels 811(H) x 508(V) 795(H) x 596(V)
Effective Pixels 768(H) x 494(V) 752(H) x 582(V)
Electronic Shutter Speed 1/60 sec 1/50 sec
S/N Ratio More than 48dB(AGC Off)
Gamma r=0.45
Min. Illumination 0.05 Lux / Face Plate
Sync System Internal
Video Output 1.0 Vp-p Composite 75(Ω) unbalanced
Power
Consumption
DC12V DC 12V (±10%) Max 110mA
Dual DC 12V (±10%) 160mA
AC 24V (±10%) 170mA / 1.8W
Operating Temperature -10℃~ +50℃
Storage Temperature -20℃~ +60℃
Operating Humidity 10% ~80%
Options Dual Power, Fan
Weight
• Surface Mount Type A : Approx. 1.38kg /
Type B : Approx. 1.1kg
• Flush type : Approx. 730g
Power
Consumption
DC12V DC 12V (±10%) Max 400mA
Dual DC 12V (±10%) 540mA
AC 24V (±10%) 440mA / 5.5W
Min. Illumination 0 Lux (IR LED ON)
IR LED 30ea
IR LED Half Angle ±22 Degree
IR LED Wavelenght 850nm
IR Beam Range Up to 30 m
IR LED Operation On : 1 Lux, Off : 3 Lux
LED TYPE
13
Face Plate : Point at the CCD without obstruction of light from any other material.

9.Setup menu operation
OSD STRUCTURE
• ▲,▼ : Menu up / down
• ◀,▶ : Set-up Key
• ■ : MENU(SELECTION KEY)
14 15
SETUP MENU
CAMERA ID • ON • OFF
LENS • MANUAL • VIDEO • DC
SHUTTER • AUTO • FLK • FIXED • MANUAL
WHITE BAL. • ATW • AWB • FIXED • MANUAL
FUNCTION
• BLC • AGC • DAY & NIGHT • PRIVACY
• MIRROR • GAMMA • MOTION
ADJUST • CONTRAST • SHARPNESS
• CB_GAIN • CR_GAIN
LANGUAGE • ENGLISH • KOREAN • CHINESE1 • CHINESE2 • JAPANESE
RESET • YES • NO
EXIT

14 15
9.Setup menu operation
1)SETUP mode
- Press and hold MENU button 1 second to access the setup mode.
SETUP menu is displayed on the monitor.
① Select OSD item using UP, DOWN button.
② Set details using LEFT, RIGHT button.
③ Select “EXIT” and then press the MENU
button to nish the SETUP.
(Save and Exit)
2)CAMERA ID
- Select CAMERA ID using UP, DOWN button
in SETUP menu.
- Set ON state using LEFT, RIGHT button.
- Press MENU button in CAMREA ID.
ID SETUP menu is displayed on the monitor.
2-1) CAMERA ID setup
① Character is changed each time UP, DOWN button is pressed.
(You can select up to 63 letters)
② Character position is changed LEFT, RIGHT button is pressed.
③ Press MENU button in to exit from ID setup mode
④ Press MENU button in ‘C’ to correct and erase the chosen entry.
2-2) POSITION setup.
① Press POSITION
② Move the character position using UP, DOWN, LEFT, RIGHT button.
③ Press MENU button to conrm the position of the character.
④ Press MENU button in RETURN to go to previous screen.
ID is displayed by pressing EXIT on SETUP menu.

9.Setup menu operation
16 17
3)LENS
3-1) LENS setup
Press LEFT or RIGHT button in LENS on SETUP menu to select the mode to
MANUAL 󰆋󰆍 VIDEO 󰆋󰆍 DC 󰆪
3-2) DC LENS setup (IRIS LEVEL setup)
① Press MENU button in DC󰆪
to display the screen.
② Use LEFT, RIGHT button to change
BRIGHTNESS(IRIS LEVEL)value.
③ Press MENU button to return
to the previous screen.
4)SHUTTER
4-1) SHUTTER setup
Press LEFT or RIGHT button in SHUTTER to select the mode to
AUTO󰆪󰆋󰆍 FLK 󰆋󰆍 FIXED󰆪󰆋󰆍 MANUAL󰆪
4-2) SHUTTER AUTO setup (AE LEVEL setup)
① Press MENU button in AUTO󰆪
to display the screen.
② Use LEFT, RIGHT button to change
BRIGHTNESS(AE LEVEL) value.
4-3) SHUTTER FIXED setup (MANUAL, DC, VIDEO LENS)
① Press MENU button in FIXED󰆪
① Press LEFT or RIGHT button in SHUTTER.
You can be set in
1/60(NTSC), 1/50(PAL) ~ 1/100,000 range.

16 17
9.Setup menu operation
4-4) SHUTTER MANUAL setup(MANUAL, DC, VIDEO LENS)
① Press MENU button in MANUAL󰆪
② Press LEFT or RIGHT button in SHUTTER M.
SHUTTER M. value is changed
between 0<MIN> ~ 255<MAX>.
0<MIN>:1/50 or 1/60,
255<MAX>:1/100,000
5)WHITE BALANCE
5-1) WHITE BALANCE setup
Press LEFT or RIGHT button in WHITE BAL. to select the mode to
ATW 󰆋󰆍 AWB 󰆋󰆍 FIXED󰆪󰆋󰆍 MANUAL󰆪
5-2) AWB FIXED setup
① Press MENU button in FIXED󰆪.
② Press LEFT or RIGHT button.
You can set from MODE 1 to MODE 4.
5-3) AWB MANUAL setup
① Press MENU button in MANUAL󰆪.
② Press LEFT or RIGHT button
in RED or BLUE.
Set Red and Blue color temperature value.

9.Setup menu operation
18 19
6)ADJUST Mode Setup
6-1) ADJUST setup
① Press MENU button in ADJUST󰆪.
② Press UP or DOWN button
to select the mode.
③ Each level value can be adjusted
using LEFT, RIGHT button.
6-2) CONTRAST setup
Adjust Y-gain value(0~255)
6-3) SHARPNESS setup
Adjust aperture value(0~31)
6-4) CB_GNIN setup
Adjust COLOR CB_GAIN value(0~255)
6-5) CR_GAIN setup
Adjust COLOR CR_GAIN value(0~255)
7)LANGUAGE Mode Setup
① DEFAULT value – ENGLISH
② After selection LANGUAGE, change setting using LEFT or RIGHT button.
③ Choose the language mode you wish to operate in
ENGLISH 󰆋󰆍 Korean 󰆋󰆍 Chinese1 󰆋󰆍 Chinese2 󰆋󰆍 Japanese
8)RESET
① Press MENU button in RESET.
② Select YES to reset your camera
to default factory condition

18 19
10.Function Menu operation
1)FUNCTION menu
- Press MENU button in FUNCTION󰆪.
on SETUP menu.
① Select item using UP, DOWN button.
② Set details using LEFT, RIGHT button.
③ Press MENU button in RETURN
to go to SETUP menu.
2)BLC
2-1) BLC SETUP mode
- Press MENU button in BLC ON󰆪.
2-2) BLC AREA setup
① Use UP,DOWN,LEFT,RIGHT button
to move the AREA setup position.
② Set or release BLC AREA
using MENU button.
③ Press MENU button for more than 1 second
to move to BLC AREA MODE

10.Function Menu operation
20 21
2-3) BLC AREA MODE
① ALL CLEAR – Clear all set AREA
② ALL SET – Set all 64 BLC AREA
③ RETURN – Return to BLC AREA
setup mode.
④ EXIT – Save AREA and
return to BLC SETUP mode.
2-4) BLC RATIO setup
① Use UP, DOWN button
to move to BLC RATIO.
② Use LEFT, RIGHT button
to change BLC LEVEL value(0~63)
0:MIN, 63:MAX
③ Press MENU button in RETURN
to move to FUNCTION MODE.
3)AGC
① AGC default setting ON󰆪.
② Press MENU button in ON󰆪.
③ Use LEFT, RIGHT button
to adjust AGC GAIN value(0~255)
0:MIN, 255:MAX
④ Press MENU button in RETURN
to the previous screen.

10.Function Menu operation
20 21
4)DAY & NIGHT (STANDARD TYPE Only)
- Press LEFT or RIGHT button in DAY NIGHT select the mode to
AUTO 󰆪󰆋󰆍 B/W󰆪󰆋󰆍 COLOR.
4-1) AUTO 󰆪 mode setup
- Press MENU button in AUTO󰆪mode.
- Select item using UP/DOWN button.
- Adjust value using LEFT/RIGHT button.
- Press MENU in RETURN to return
to the previous screen
NOTE) Auto mode does not operate in
True D&N Type but operate in Standard type.
NOTE) When AGC mode is turned off, AUTO mode does not operate.
NOTE) The camera of True D&N type in Day & Night function is under
the control of photocell
① DELAY
DAY NIGHT or NIGHT DAY conversion time setup
0 : No DAY NIGHT AUTO conversion
1~63 : Can set from 1 second to 15 seconds
② START LEVEL
DAY  NIGHT conversion illumination intensity setup 0~255
0 : High illumination intensity, 255 : Low illumination intensity
NOTE) Initial value setup is recommended.
③ END LEVEL
NIGHT  DAY conversion illumination intensity setup 0~255
0 : High illumination intensity, 255 : Low illumination intensity
NOTE) Initial value setup is recommended.
4-2) B/W󰆪mode setup
①Press MENU in B/W󰆪.
②Move to screen on the right side.
③Use LEFT, RIGHT button
to set BURST ON/OFF.
④After setup, return to the previous screen
by pressing MENU button.