KTI Networks KGS-1064-BP User manual

-1-
KGS-1064-BP
Industrial Managed
10-Port Gigabit Ethernet Switches
with 2 Dual-speed SFP Slots and 8 PoE PSE Ports
(IEEE 802.3bt PoE)
Firmware Rev1.0 up
User’s Manual
DOC.210223A

-2-
99B(C) 2021 KTI Networks Inc.
All rights reserved. No part of this documentation may be reproduced in any form or by any means or used to
make any directive work (such as translation or transformation) without permission from KTI Networks Inc.
KTI Networks Inc. reserves the right to revise this documentation and to make changes in content from time to
time without obligation on the part of KTI Networks Inc. to provide notification of such revision or change.
For more information, contact:
15F-7, No. 79, Sec. 1, Hsin-Tai-Wu RD
His-chih, New Taipei City, Taiwan
Fax: [phone]
E-mail: [email protected]
URL: http://www.ktinet.com.tw/

-3-
The information contained in this document is subject to change without prior notice.
Copyright ©All Rights Reserved.
112TRADEMARKS
Ethernet is a registered trademark of Xerox Corp.
FCC NOTICE
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) This device must accept any interference received,
including the interference that may cause undesired operation.
CE NOTICE
Marking by the symbol indicates compliance of this equipment to the EMC directive of the European
Community. Such marking is indicative that this equipment meets or exceeds the following technical
standards:
EN 61000-6-4
EN 61000-3-2, EN 61000-3-3
EN 61000-6-2
IEC 61000-4-2, IEC 61000-4-3, IEC 61000-4-4
IEC 61000-4-5, IEC 61000-4-6, IEC 61000-4-8
IEC 61000-4-11
EN 50121-4 Certified
EN 50121-1 EMI
EN 61000-6-4
EN 61000-3-2, EN 61000-3-3
EN 50121-4 EMS
EN 61000-4-2, EN 61000-4-3, EN 61000-4-4
EN 61000-4-5, EN 61000-4-6, EN 61000-4-8
EN 61000-4-9
VCCI-A Notice

-4-
Table of Contents
0B1. Introduction..................................................................................................................................................5
1.1 Features...............................................................................................................................6
1.2 Product Panels.....................................................................................................................7
1.3 LED Indicators......................................................................................................................8
1.4 Specifications.......................................................................................................................8
1B2. Installation..................................................................................................................................................11
10B2.1 Unpacking.....................................................................................................................11
2.2 Safety Cautions..................................................................................................................11
12B2.3 DIN-Rail Mounting ........................................................................................................12
13B2.4 Panel Mounting.............................................................................................................14
14B2.5 Applying Power.............................................................................................................16
2.6 Alarm Relay Output............................................................................................................17
2.7 Reset Button ......................................................................................................................18
2.8 Making UTP Connections...................................................................................................19
2.9 Making Fiber Connection....................................................................................................20
2.10 Making PoE PSE Connections.........................................................................................22
2.11 LED Indication..................................................................................................................24
2.12 Making Console Connection.............................................................................................25
3. Managing the Switch.....................................................................................................................................26
3.1 IP Address & Password......................................................................................................26
3.2 Configuring IP Address & Password via console and telnet................................................26
3.3 Configuring IP Address via Web Interface..........................................................................27
3.4 Reference Manuals for Web, Console, Telnet Management...............................................29
3.5 Configuration for SNMP Management................................................................................30
3.6 SNMP MIBs........................................................................................................................31
3.6.1 SNMP Traps....................................................................................................................32
4. Redundant Ring Applications......................................................................................................................33
4.1 Auto Multi-Ring Technology ...............................................................................................33
4.2 Redundant Ring Applications with industrial standard RSTP protocol................................34

-5-
0B1. Introduction
131The KGS-1064-BP is a 10-port industrial managed Gigabit Ethernet switch which is featured with the
following communication ports:
⚫Eight 10/100/1000Mbps Gigabit copper ports with PoE function
⚫Two dual-speed SFP slots for 100Base-FX 1000Base-X
⚫One RS-232 console port

-6-
1.1 Features
⚫Eight 10/100/1000Mbps RJ-45 and two dual-speed SFP slots
⚫All copper ports support auto-negotiation and auto-MDI/MDI-X detection.
⚫All copper ports are equipped with 802.3bt-compliant PoE PSE function
⚫Two SFP slots support dual speed for 100BASE-FX and 1000BASE-X SFP transceivers.
⚫Full wire speed forwarding
⚫Supports 802.3x flow control for full-duplex and backpressure for half-duplex
⚫Supports SFP with Digital Diagnostic Monitoring (DDM)
⚫Provides PoE PSE redundancy function
⚫Provides fiber Optical Power Alarm (OPA) function
⚫Provides Automatic Laser Shutdown (ALS) function
⚫Management:
- HTTP/HTTPS/SSHv2/CLI telnet/CLI console/SNMP v1/v2c/v3/RMON
- DHCP/DHCPv6 client, DHCP relay, DNS client, NTPv4
- IPv6 support, System Syslog, Configuration down/upload, Software upload
⚫Security:
- NAS, 802.1X, MAC-based/Web/CLI authentication
- IP MAC binding, TACACS+, IP source guard
⚫Layer 2:
- QoS, 802.1Q/MAC-based/Protocol-based/Private/IP subnet VLAN, Port Isolation
- Storm control for UC/MC/BC packets, Static MAC configuration
- IGMP v2/v3 snooping, MLD v1/v2 snooping, DHCP snooping
- Multiple Spanning Tree - MSTP. RSTP, STP
⚫Auto Multi-Ring (KAMR) Technology:
- Fast failover response time
- Auto recovery when failure is repaired
- Supports up to five redundant rings
- Works with RSTP network
⚫Specific SNMP implementation:
- Private MIB for reading DDM status
- Private MIB for remote boot the device over SNMP
- Private MIB for TFTP firmware update over SNMP
- Private MIB for configuring OPA function
- Private MIB for configuring ALS function
- OPA alarm traps

-7-
1.2 Product Panels
The following figure illustrates the front panel and rear panel of the switch:
Front panel
154BTop panel

-8-
1.3 LED Indicators
LED Function
PWR Power status
Mgt. Management status
Port 1~ 8 SPEED LEDs Speed & PoE status
Port 1~ 8 LINK LEDs Link & activity status
SFP 9, 10 LEDs Speed & link & activity status of SFP port
1.4 Specifications
10/100/1000 Copper Ports (Port 1 ~ Port 8)
Compliance IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX, IEEE 802.3u 1000Base-T
Connectors Shielded RJ-45 jacks
Pin assignments Auto MDI/MDI-X detection
Configuration Auto-negotiation or software control
Transmission rate 10Mbps, 100Mbps, 1000Mbps
Duplex support Full/Half duplex
Network cable Cat.5 UTP
Dual-speed SFP Slots (Port 9, Port 10)
Compliance IEEE 802.3u 100Base-FX
IEEE 802.3z 1000Base-SX/LX
Connectors SFP for optional SFP type fiber transceivers
Configuration Auto 1000Mbps, Full duplex
Forced 100Mbps, Full duplex
Transmission rate 100Mbps and 1000Mbps
Network cables MMF 50/125m 62.5/125m, SMF 9/125m
Eye safety IEC 825 compliant
Console Port
Interface RS-232, DTE type, galvanic isolation
Connector Shielded RJ-45
Switch Functions
MAC Addresses Table 8K entries
Forwarding & filtering Non-blocking, full wire speed
Switching technology Store and forward

-9-
Maximum packet length 9.6K bytes
IP Multicast groups 8192 supported
Flow control IEEE 802.3x pause frame base for full duplex operation
Back pressure for half duplex operation
Power over Ethernet PSE Function
PSE Ports Port 1 ~ Port 8
Standard IEEE 802.3af, IEEE 802.3at, and IEEE 802.3bt
PD classes support PSE port output vs. PD input
Compliant
PD classes
IEEE std.
DC power
min. *1
PSE output
power max. *2
Cable
power pairs
PD Available
power min. *3
802.3af
802.3at
802.3bt
Class 1



45V
5.3W
2
3.84W
Class 2



45V
8.5W
2
6.49W
Class 3



45V
19W
2
13W
Class 4


45V
36W
4
25.5W
Class 5

51V
51W
4
40W
Class 6

51V
68W
4
51W
Class 7

53V
83W
4
62W
Class 8

53V
95W
4
71.3W
*1: The minimum DC power voltage to support the specified PSE output
*2: The maximum output power at the PSE end for the requested PD class
*3: The minimum power received at the PD end with maximum output at the PSE end in worst case
Power Delivery 95W max. (per port) at port output for Cat.5 distance up to 100 meters
PSE power pins Pin 1/2/4/5: Vpoe+, Pin 3/6/7/8: Vpoe- (Vpoe comes from DC power input)
Power delivery 95W max. at port output (Depending on DC power voltage)
Protection PoE output shutdown
Protection events Incompliant PD detection, PD disconnection
Overload, Over-current, Short-circuit, Under voltage
Power Capacity 240W shared by all PSE ports
Terminal Block Connector
DC power input Screwed euro terminal block: DC +/- contacts
Operating Input Voltages +12 ~ +60VDC for general applications
+45 ~ +57VDC for PoE applications
Power consumption 10.3W max. (Full load with no PSE output)
250.3W max. (with full PoE output)
Alarm relay output 3 terminal contacts (30VDC/1A max. or 120VAC/0.5A max.)

-10-
NC contacts: normal –shored, alarm –open
NO contacts: normal –open, alarm –shored
Alarm events Power failure, Specific port link fault (software configured), OPA
856BUMechanical
Dimension 140 x 106 x 60 mm (HxDxW)
Housing Enclosed metal with no fan
Mounting Din-rail mounting, Panel mounting (optional)
860BUEnvironmental
Operating Temperature Typical -30℃~ +70℃
Storage Temperature -40℃~ +85℃
Relative Humidity 5% ~ 95% non-condensing
864BUElectrical Approvals
FCC Part 15 rule Class A
CE EN 61000-6-4, EN 61000-6-2 EMC
VCCI Class A
Safety / LVD IEC 62368-1
EN 50121-4 EMC for railway applications

-11-
1B2. Installation
10B2.1 Unpacking
The product package contains:
⚫The switch unit
⚫QR code label
⚫One console cable
2.2 Safety Cautions
To reduce the risk of bodily injury, electrical shock, fire and damage to the product, observe the following
precautions:
Do not service any product except as explained in your system documentation.
Opening or removing covers may expose you to electrical shock.
Only a trained service technician should service components inside these compartments.
If any of the following conditions occur, unplug the product from the electrical outlet and replace the
part or contact your trained service provider:
-The power cable, extension cable, or plug is damaged.
-An object has fallen into the product.
-The product has been exposed to water.
-The product has been dropped or damaged.
-The product does not operate correctly when you follow the operating instructions.
Do not push any objects into the openings of your system. Doing so can cause fire or electric shock by
shorting out interior components.
Operate the product only from the type of external power source indicated on the electrical ratings
label. If you are not sure of the type of power source required, consult your service provider or local
power company.
Since the surface temperature of the device may be higher than 70℃in range of
the rated operating temperatures, install and operate the product only by authorized
personnel only. Install the product at a restricted area where un-authorized persons
cannot reach.

-12-
12B2.3 DIN-Rail Mounting
171BIn the product package, a DIN-rail bracket is provided for mounting the switch in a industrial DIN-rail
enclosure.
172BThe steps to mount the switch onto a DIN rail are:
1. 1287BInstall the mounting bracket onto the switch unit as shown below:
2. 1288BAttach bracket to the lower edge of the DIN rail and push the unit upward a little bit until the bracket can
clamp on the upper edge of the DIN rail.
3. 1289BClamp the unit to the DIN rail and make sure it is mounted securely.

-13-
Dimensions:

-14-
13B2.4 Panel Mounting
173BThe switches are provided with an optional panel mounting bracket. The bracket supports mounting the switch
on a plane surface securely.
The mounting steps are:
1. 1290BInstall the mounting bracket on the switch unit.
2. 1291BScrew the bracket on the switch unit.
3. 1292BScrew the switch unit on a panel. Three screw locations are shown below:

-15-
Dimensions:

-16-
14B2.5 Applying Power
Power pins of the terminal block connector
Pin
1
+
Vdc Positive (+) input terminal
2
-
Vdc Negative (−) input terminal
Vdc Input specifications
Working voltage range
Applications
Power output at PSE port
+12V ~ +60VDC
General
-
+45V ~ +57VDC
PoE, PoE+
+51V, 36W max.
+53V ~ +57VDC
PoE++
+53V, 95W max.
A 2P terminal plug is provided together with the switch as shown below:
Power wires : 24 ~ 12AWG (IEC 0.5~2.5mm2), 1 meter max.

-17-
2.6 Alarm Relay Output
Alarm relay output is provided for reporting failure events to a remote alarm relay monitoring system. The
replay output is provided with three contacts (support two logic types) in the terminal block connector next
Vdc interfaces.
Alarm Relay output pins and logic:
Pin
3
4
Alarm relay output, NO (Normal Open) contacts
Open: Normal, Shorted: Alarm
NO
Pin
4
5
Alarm relay output, NC (Normal Closed) contacts
Shorted: Normal, Open: Alarm
NC
Either pair can be used depending on the logic requirement for the relay monitoring system.
Use the provided 3P terminal plug for signal wiring and plug into the contacts.
Alarm Events
⚫196BInput power failure
⚫197BSpecific port link down (The specific ports can be configured by software.)
⚫OPA alarm if optical power is higher than a upper limit setting or lower than a lower limit setting
Note: Be sure the voltage applied on the contacts is within the specification of 30VDC/1A max. or
120VAC/0.5A max.

-18-
2.7 Reset Button
The reset button is used to perform a reset to the switch. It is not used in normal cases and can be used for
diagnostic purpose. If any network hanging problem is suspected, it is useful to push the button to reset the
switch without turning off the power. Check whether the network is recovered.
The button can also be used to restore the software configuration settings to factory default values.
The operations are:
Operation
Function
Press the button and release during switch operation
Reset & boot up the switch.
The boot-up takes about 20 seconds and ends with all LED
yellow ON and green ON then all OFF once.
Press the button until all LED yellow ON and green ON,
then all OFF.
Boot & restore all factory default settings

-19-
2.8 Making UTP Connections
The 10/100/1000 RJ-45 copper ports support the following connection types and distances:
Network Cables
10BASE-T: 2-pair UTP Cat. 3, 4, 5 , EIA/TIA-568B 100-ohm
100BASE-TX: 2-pair UTP Cat. 5, EIA/TIA-568B 100-ohm
1000BASE-T: 4-pair UTP Cat. 5 or higher (Cat.5e is recommended), EIA/TIA-568B 100-ohm
Link distance: Up to 100 meters for all above
Auto MDI/MDI-X Function
This function allows the port to auto-detect the twisted-pair signals and adapts itself to form a valid MDI to
MDI-X connection with the remote connected device automatically. No matter a straight through cable or
crossover cable is connected, the ports can sense the receiving pair automatically and configure itself to match
the rule for MDI to MDI-X connection. It simplifies the cable installation.
Auto-negotiation Function
The ports are featured with auto-negotiation function and full capability to support connection to any Ethernet
devices. The port performs a negotiation process for the speed and duplex configuration with the connected
device automatically when each time a link is being established. If the connected device is also
auto-negotiation capable, both devices will come out the best configuration after negotiation process. If the
connected device is incapable in auto-negotiation, the switch will sense the speed and use half duplex for the
connection.
Port Configuration Management
For making proper connection to an auto-negotiation incapable device, it is suggested to use port control
function via software management to set forced mode and specify speed and duplex mode which match the
configuration used by the connected device.

-20-
2.9 Making Fiber Connection
The dual-speed SFP slots, Port 9 and Port 10 must be installed with an SFP fiber transceiver for making fiber
connection. The switch may come with one or two SFP transceivers pre-installed when it is shipped.
Types of the SFP Fiber transceivers supported:
1000Mbps based 1000BASE-X SFP transceivers
100Mbps based 100BASE-FX SFP transceivers
Installing SFP Fiber Transceiver
217BTo install an SFP fiber transceiver into SFP slot, the steps are:
1. Turn off the power to the switch.
2. Insert the SFP fiber transceiver into the SFP slot. Normally, a bail is provided for every SFP
transceiver. Hold the bail and make insertion.
3. Until the SFP transceiver is seated securely in the slot, place the bail in lock position.
Connecting Fiber Cables
LC connectors are commonly equipped on most SFP transceivers. Identify TX and RX connector