Kuryakyn Road Thunder User manual

PAGE 1
302714
DPF-MRK-003 REV A 6/20/16
ROADTHUNDER SOUND BAR BY MTX, SATIN SILVER 2714
866 277 9598 | [e-mail]
454 COUNTY ROAD VV SOMERSET, WI 54025
KURYAKYN.COM
INSTALLATION INSTRUCTIONS
THANK YOU FOR CHOOSING KURYAKYN!
Protect yourself and others from possible injury and property damage or loss. Pay close attention to all instructions, warnings, cautions, and notices regarding the installation, use, and care of this product.
THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED HEREIN CAN RESULT IN POTENTIAL DEATH OR SERIOUS INJURY.
THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED HEREIN CAN RESULT IN MINOR OR MODERATE POTENTIAL INJURY.
THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED HEREIN MAY NEGATIVELY AFFECT PRODUCT PERFORMANCE AND FUNCTIONALITY OR
DAMAGE THE PRODUCT ITSELF OR THE PRODUCT TO WHICH IT IS BEING ATTACHED.
ENSURE THAT THE FOLLOWING PARTS HAVE BEEN INCLUDED IN THE KIT:
1RoadThunder® Sound Bar
1Hardware Kit containing:
2Sound Bar Mounting Clamps 2M6-1.0 X 35MM Button Head
Hex Screws
27/8” Clamps 2M6-1.0 Lock Nut w/Washers
21” Clamps 2M6-1.0 X 14MM Cap Screws
21-1/8” Clamps 2M6 Split Washers
21-1/4” Clamps 2M4-0.7 X 10MM Set Screws
1Transparent Film 12MM Allen Wrench
110 Amp Mini Fuse
1Quick Connect Male
1T-Tap Quick Connect Female
4Cable Ties
YOU WILL ALSO NEED:
Metric Hex, Allen wrenches, hand crimping tool(18-22 AWG), pliers
THESE INSTALLATION INSTRUCTIONS CONTAIN IMPORTANT INFORMATION. ENSURE THE END USER RECEIVES THIS COPY AND IS AWARE
OF ITS IMPORTANCE FOR FUTURE USE.
WHEN CONNECTING POWER AND GROUND WIRES ENSURE THAT THE RED POWER WIRE IS FUSED AT THE POINT WHERE IT IS
CONNECTED TO THE VEHICLE’S BATTERY. FAILURE TO DO SO CAN RESULT IN DAMAGE TO THE VEHICLE IF A SHORT CIRCUIT DEVELOPS
BETWEEN THE VEHICLE CONNECTION POINT AND THE PRODUCT.

PAGE 2
302714
DPF-MRK-003 REV A 6/20/16
ROADTHUNDER SOUND BAR BY MTX, SATIN SILVER 2714
866 277 9598 | [e-mail]
454 COUNTY ROAD VV SOMERSET, WI 54025
KURYAKYN.COM
INSTALLATION INSTRUCTIONS
-CONTINUED-
INTRODUCTION
Thank you for purchasing this Kuryakyn RoadThunder Sound Bar by MTX that is designed to work with most Bluetooth enabled devices including
iPhone® and Android® smartphones and tablets. This easy to install and use, all in one unit is capable of transforming your Bluetooth enabled mobile
device into the center of your vehicle’s audio system. It is designed to mount on a variety of bars between 7⁄8” and 1-1⁄4”. Congratulations and enjoy
the ultimate audio experience!
FEATURES
• Two 2” x 3” Full Range Speakers and Four 1” High Frequency Tweeters
• All-Weather Construction for Use In Almost Any Environment
• Integrated Bluetooth Receiver
• Auxiliary Input for Connecting Devices Via 3.5mm Cable
• Auxiliary Output for Connecting An External Amplifier or Additional Sound Bar
• Patent Pending Universal Mounting Clamps Fit Bars Between 7⁄8” and 1-1⁄4”
• Power, Ground, Ignition Wire, and 12V Trigger Output Included for Easy Installation
• Automated Bluetooth Pairing via NFC
INSTALLATION
The RoadThunder Sound Bar can be used with any 12-volt battery and can be mounted to a variety of bars using the included
hardware. The unit has four wires in its wiring pigtail. The red wire, hot, should be directly connected to the vehicles positive battery
terminal. The black wire, ground, should be connected directly to the vehicle’s chassis where paint has been removed or the negative
terminal on the battery. Use the included T-Tap Quick Connect Female connector and install directly onto the ACC/Key ignition wire
on the motorcycle using a pair of pliers. Crimp and connect the Quick Connect Male to the orange ignition wire on the Sound Bar.
Once the Quick Connect Male & T-Tap Quick Connect Female have been attached to their wires connect them together. The blue wire,
optional output, can be used to turn on additional amplifiers.
The unit features fully adjustable clamps for mounting to bars between 7⁄8” and 1-1⁄4”. The clamps can be used to mount to many
styles of handlebar and roll bar systems. The included brackets are versatile, so mounting to angled bars is possible.
SCENARIO 1 - MOUNT CLAMPS TO HANDLEBAR FIRST, THEN INSTALL SOUND BAR.
• Choose the correct size strap clamp for the handlebars.
Note: Placing the transparent film between the strap clamp and handlebar will reduce the possibility of scratching the handlebars during installation.
• Assemble mid-section to bottom bracket using included 5mm Allen Screw and 10mm Hex Nut.
• Ensure that the spacing between the brackets is between 3” and 6.75”.
• Slide the sound bar into the brackets from the left side, so the brackets can clear the buttons without damaging them.
• Rotate the sound bar so the speakers are directed at the rider’s head.
• Tighten the 5mm Allen Screws to lock the sound bar in place.
• Tighten the 2mm Set Screws.
• Connect wires to power, ground, and ignition.

PAGE 3
302714
DPF-MRK-003 REV A 6/20/16
ROADTHUNDER SOUND BAR BY MTX, SATIN SILVER 2714
866 277 9598 | [e-mail]
454 COUNTY ROAD VV SOMERSET, WI 54025
KURYAKYN.COM
INSTALLATION INSTRUCTIONS
INSTALLATION
SCENARIO 2 - INSTALL SOUND BAR, THEN MOUNTS CLAMPS TO HANDLEBAR.
• Choose the correct size strap clamp for the handlebars.
Note: Placing the transparent film between the strap clamp and handlebar will reduce the possibility of scratching the handlebars during installation.
• Slide the sound bar into the brackets from the left side, so the brackets can clear the buttons without damaging them.
• Ensure that the spacing between the brackets is between 3” and 6.75”.
• Assemble mid-section to bottom bracket using included 5mm Allen Screw and 10mm Hex Nut.
• Rotate the sound bar so the speakers are directed at the rider’s head.
• Tighten the 5mm Allen Screws to lock the sound bar in place.
• Tighten the 2mm Set Screws.
• Connect wires to power, ground, and ignition.
ORIENTATION EXAMPLES
-CONTINUED-

PAGE 4
302714
DPF-MRK-003 REV A 6/20/16
ROADTHUNDER SOUND BAR BY MTX, SATIN SILVER 2714
866 277 9598 | [e-mail]
454 COUNTY ROAD VV SOMERSET, WI 54025
KURYAKYN.COM
INSTALLATION INSTRUCTIONS
ELECTRICAL OPERATION
STEP 1 Tap the Power button to turn the unit on. (Power, Ground, and Ignition wire need
to be connected to a 12V power source.)
STEP 2 Tap the Power button to switch modes between Bluetooth and AUX.
STEP 3 Hold the Power button for 2 seconds to turn the unit Off.
STEP 4 The integrated fuse and ring terminals allow for easy wire connection to a 12V
power source.
STEP 5 The remote turn on (blue wire) only operates when the unit is powered on.
Note: The indicator light will illuminate Blue when in Bluetooth mode and Green
when in AUX mode.
OPERATION
FOLLOW THESE STEPS TO UTILIZE THE BLUETOOTH FUNCTIONALITY USING A BLUETOOTH
ENABLED DEVICE:
STEP 1 Power the unit On by tapping the Power button once.
STEP 2 Select Bluetooth by tapping the Power button until it blinks Blue.
STEP 3 Select “MTX Sound Bar” from the menu on your Bluetooth enabled device. The
unit will power on in Bluetooth mode first when it is turned on by tapping. If the
Ignition wire is disconnected, (vehicle is turned off and then turned on) the unit
will revert back to the previous Bluetooth or AUX setting.
STEP 4 Choose “Pair” when prompted.
STEP 5 Once “Paired” the unit will be able to play audio from your Bluetooth device.
The front panel control buttons will control track forward/back and volume up/
down in this mode. The Play/Pause button will mute the output and the LED
indicator will blink Blue when in Mute mode.
FOLLOW THESE STEPS TO UTILIZE BLUETOOTH IN A NFC (NEAR FIELD COMMUNICATION)
ENABLED DEVICE:
STEP 1 Power the unit On by tapping the Power button once.
STEP 2 Select Bluetooth by tapping the Power button until it blinks Blue.
STEP 3 Tap the NFC enabled device on the (left) side of the enclosure (marked by NFC
label).
STEP 4 Choose “Pair” when prompted.
STEP 5 Once “Paired” the unit will be able to play audio from your NFC device.
FOLLOW THESE STEPS TO UTILIZE AN AUXILIARY INPUT DEVICE:
STEP 1 Power the unit On by tapping the Power button once.
STEP 2 Select Auxiliary by tapping the Power button until it blinks Green.
STEP 3 Connect an audio device to the AUX input using the “Green” 3.5mm input on
the side of the unit. The LED will illuminate Green, and will blink Green when in
mute mode.
The front panel control buttons will adjust the Volume up/down in this mode. The
Play/Pause button will mute the audio output and the LED indicator will blink
Green when in Mute mode.
USING THE AUXILIARY OUTPUT. OUTPUT MARKED ON (LEFT) SIDE OF ENCLOSURE.
STEP 1 Auxiliary out is a variable output that allows connection to a secondary audio
device, whether it is an external amplifier connected to speakers or subwoofer.
-CONTINUED-

PAGE 5
302714
DPF-MRK-003 REV A 6/20/16
ROADTHUNDER SOUND BAR BY MTX, SATIN SILVER 2714
866 277 9598 | [e-mail]
454 COUNTY ROAD VV SOMERSET, WI 54025
KURYAKYN.COM
INSTALLATION INSTRUCTIONS
STEP 2 The RoadThunder Sound Bar can be used with a second RoadThunder Sound
Bar unit. For the best audio performance, the second unit connected via Auxilia-
ry should have the volume set to the max.
STEP 3 The blue wire on the wire harness can be used as a remote turn on for the
second audio device.
CONTROLLING THE VOLUME
The LED indicator light will blink in both Bluetooth and AUX modes at max
volume.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, this is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, you are encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a different circuit than the one to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired operation.
LIMITED WARRANTY
Kuryakyn warrants that any Kuryakyn products sold hereunder, shall be free of defects in materials & workmanship for a period of one (1) year from the date of
purchase by the consumer excepting the following provisions:
1. Kuryakyn shall have no obligation in the event the customer is unable to provide a receipt showing the date the customer purchased the product(s).
2. The product must be properly installed, maintained & operated under normal conditions.
3. Kuryakyn shall not be liable for any consequential & incidental damages, including labor & paint, resulting from failure of a Kuryakyn product, failure to deliver, delay
in delivery, delivery in nonconforming condition, or for any breach of contract or duty between Kuryakyn & a customer.
4. Kuryakyn products are often intended for use in specific applications. Kuryakyn makes no warranty if a Kuryakyn product is used in applications other than intended.
5. Kuryakyn electrical products are warranted for one (1) year from the date of purchase by the consumer. L.E.D.’s contained in components of Kuryakyn products will
be warranted for defects in materials & workmanship for 3 years from the date of purchase whereas all other components shall be warranted for one (1) year.
6. All warranty claims must be directed to the place of purchase. Merchandise sold through internet auction sites or any other unauthorized reseller shall not carry a
Kuryakyn warranty. If unsure, please contact the place of purchase to verify they are an authorized Kuryakyn reseller.
RETURN POLICY
Merchandise determined to be defective may be returned up to one year from the date of purchase. Returns must be processed through original seller. Returned
merchandise for any other reason other than warranty claims must be in like new condition & subject to a 20% restocking fee. All returns are subject to inspection
for determination of full or partial credit. Any returned part that shows evidence of being used or installed contrary to manufacturer’s instructions, &/or subjected to
improper handling, packaging or return shipping by the customer, will not be eligible for exchange, refund or warranty consideration. All returned electrical items will be
inspected & tested. If electrical item is deemed functional, no credit will be issued & item will be returned. All sales are final on discontinued or closeout merchandise.
©2015 KURYAKYN HOLDINGS, LLC ALL RIGHTS RESERVED
KURYAKYN, KURYAKYN K logo and the marks appearing on this instruction sheet are registered and common law trademarks of Kuryakyn Holdings except noted third-party trademarks. A full listing of trademarks and trademark
registrations owned by Kuryakyn Holdings can be found at www.kuryakyn.com/legal-notice.
Emissions Notice: The California Air Resources Board (CARB) does not permit the use of aftermarket emission-related parts(s) that alter the performance of OEM emission-related devices unless CARB has issued an Executive
Order, other than on racing vehicles on closed courses. Check your local laws and manufacturer’s information.
Listed Manufacturers and product model names are for reference only. All product and company names are trademarks or registered trademarks of their respective holders. Use of them does not imply any affiliation with or
endorsement by them. All specifications are subject to change without notice.
For additional information on third-party product and company names, please consult our Web page at www.kuryakyn.com/legal-notice
-CONTINUED-