KUSSMAUL 091-28 User manual

INSTRUCTION MANUAL
TEL: in NY 631-567-0314 TOLL FREE: 800-346-0857 FAX: [phone]
1 YEAR WARRANTY
BOOK# 091-28-1
AIR EJECT
AUTOMATIC AIR LINE DISCONNECT
KUSSMAUL ELECTRONICS CO., INC.
170 CHERRY AVE., WEST SAYVILLE, N.Y. 11796
MODEL #091-28

INTRODUCTION
The Air Eject is a specially designed pneumatic cylinder with an integral solenoid valve
which, when the vehicle is started, disconnects the air line connected to it. The Air
Eject is supplied with the following components:
1. Cylinder Assy
2. Check Valve
3. Gasket
4. Mounting Screws
5. Mating Female Connector
6. Bezel
INSTALLATION
HOLE TEMPLATE
Note: The 1 3/8" diameter hole is critical. If this hole is too
small it will prevent piston from striking Female connector.

INSTALLATION
1. In order to accurately locate the 3 mounting holes first locate the center of the large
hole and mark with a center punch mark. Using a compass scribe 1 3/4" dia. circle. Locate
the bezel over this scribed circle, mark the 3 mounting holes & center punch each hole.
2. Drill 3 mounting holes, 3/16" diameter. Drill 1 center hole using hole saw or conduit
punch. 1 3/8" diameter.
3. Mount the Cylinder Assembly as illustrated.
4. Install the check valve being certain that the arrow on the check valve points away from
the cylinder assembly.
5. Connect tubing as required to vehicle’s air system.
TRUCK WALL
CYLINDER
ASSEMBLY SCREWS
NOTE LOCATION OF ARROW
ON CHECK VALVE
ARROW MARK IS VERY SMALL
OUPUT TO
VECHICLE'S
AIR SYSTEM
GASKET
BEZEL
MOUNTING AIR EJECT

1. Wire the solenoid valve to the vehicle’s starting circuit. Be certain that the solenoid is
energized only while the vehicle is cranking and deenergized at all other times.
MAINTENANCE
The Air Eject is a precision device designed and manufactured for many years of reliable
service. Periodic servicing, cleaning and lubricating are important.
It is suggested that the cylinder assembly be inspected regularly and cleaned and lubricated
at a minimum once every six months.
In applications where contamination by water and road dirt are excessive, more frequent
servicing may be required.
Lubrication should be only with non-petroleum based lubricants such as Dow Corning DC-
4 Silicone grease, Silicone or Teflon spray.
WIRING
TO STARTER
SWITCH STARTER
AIR
EJECT
TO CHASSIS
GROUND
_
+
BATTERY
TO CHASSIS
GROUND
WIRING AIR EJECT
STARTER
SOLENOID

INSTALLATION RECORD & WARRANTY
Date Installed
Installed By
Vehicle Identification
Vehicle Owner
WARRANTY
AllproductsofKussmaulElectronicsCompanyInc.arewarrantedtobe
free of defects of material or workmanship. Liability is limited to repairing or
replacing at our factory, without charge, any material or defects which
become apparent in normal use within 1 year from the date the equipment
wasshipped.Equipmentistobereturned,shippingchargesprepaidandwill
be returned, after repair, shipping charges paid.
KussmaulElectronicsCompany,Inc.shallhavenoliabilityfordamages
of any kind to associated equipment arising from the installation and /or use
ofthe KussmaulElectronics Company,Inc. products.The purchaser,by the
acceptance of the equipment, assumes all liability for any damages which
may result from its installation, use or misuse, by the purchaser, his or its
employees or others.
MODEL 091-28-AK
WEATHERPROOF ADAPTER KIT
TheWeatherproofAdapterKitprovidesarecessedmount-
ingfortheAirEjectandagasketedcover whichautomati-
cally closes when the air line is ejected . A rugged
polypropylene sleeve covering the female coupler per-
mitseasymanualremovaloftheairlineandprotectsthe
coupler from damage during automatic release.
NEW COVER
The weatherproof adapter kit
comeswitha newcoverthathas
an Air Eject label inserted on the
front
NEW
ALSO AVAILABLE