Kyocera Mita Ecosys FS-C8008N Series User manual

FS-C8008N/DN Important!
Installation should be performed only by a qualified service personnel. Kyocera Mita
assumes no liability for any damage caused by an improper installation of the printer.
Placing the Printer
Checking Parts and ComponentsUnpacking
Using another topple-resistant bracket,
stack and joint the middle and top paper
feeder.
Place the printer over the paper feeders (by
at least four persons).
Join the printer and topmost paper feeder
with the jig provided by using one screw.
Using a topple-resistant bracket (supplied
with the CA-31B caster kit), stack and joint
the bottom and middle paper feeder.
Remove the tape and then open the
front cover.
Pull out thoroughly the paper transfer unit. Unscrew the screw. Remove the lock pin
and release the (green-colored) lock lever.
Pull out the primary transfer unit until it
stops.
While pushing the gray lever, pull out
the primary transfer unit. Make sure
not to scratch the roller.
Installation Guide
Continued on
the Reverse Page
Attaching the Caster kit (purchased
separately): Stand the paper feeder on its
back side. Remove each one screw to
remove four feet.
Place the paper feeder in a proper location.
Lock the stopper for each caster. Turn the
bolts to adjust height.
Install the exhaust duct and the quick
reference guide holder. Peel the protective
tape off when attaching the holder.
Be sure to face
the longer end
towards the front
of the feeder.
Gray Lever
Exhaust Duct
Quick Reference
Guide Holder
Unpacking the Printer
Unpacking
the Paper Feeder
To avoid injury,
the printer must
be lifted and
carried by four
persons or more.
The following setup assumes three paper feeders to be installed with the printer (including the one supplied as a standard accessory), which requires a CA-31B caster kit to
be installed on the bottom of the bottom paper feeder. If the extra paper feeders are not installed, the CA-31 casters may be used. See the Operation Guide for more details.
1 Documents
Installation Guide (This sheet)
Quick Reference Guide
CD-ROMs
2 Cyan Developer
3 Magenta Developer
4 Yellow Developer
5 Black Developer
6 Cyan Toner Container
7 Magenta Toner Container
8 Yellow Toner Container
9 Black Toner Container
10 Secondary Transfer Unit
11 Fuser Unit
12 Waste Toner Boxes
13 Power Cord
14 Exhaust Duct
15 Quick Reference Guide Holder
16 Jig (Used in step 9)
17 Secondary Transfer Unit Anchor Jig
(Used in step 20)
18 Screw M4 (Used in step 9)
19 Screw M3 (Used in step 16)
20 Screws M3 (Used in step 20)
Screw
Lock Pin
Install the caster kit onto the bottom of the
paper feeder.
Installing the Fuser Unit, Secondary Transfer Unit, and Waste Toner Box
PF-30A for FS-C8008N
PD-800 for FS-C8008DN
Tape
3
1 2
4 5 6
7 8 9 10
11 12 13 14

Inserting the Developer Units
Installing the Fuser Unit, Secondary Transfer Unit, and Waste Toner Box
Close the paper transfer unit.
Set the black developer facing the
developing roller towards you.
Open the paper guide. Insert the fuser unit
onto the paper transfer unit.
Installing the Toner Containers
Shake each toner container well
before use. Install the four toner
containers into their corresponding
developer units.
Close the front cover.
Fix the fuser unit with one screw. Open the fuser top cover.
Pull out the paper transfer unit. Reinstall the primary transfer unit. Insert
it thoroughly on the rails.
Close the lock lever. Fix the screw.
Reinsert the paper transfer unit.
Set the cyan developer. Set the magenta developer. Set the yellow developer.
Pull out the process frame.
Paper Guide
Fuser Unit
Fuser
Top Cover
Firmly tighten two screws. Close the fuser
top cover, then close the paper guide.
Install the waste toner box.
Install the secondary transfer unit.
Waste Toner Box
Cyan
Magenta
Yellow
Black
Making Connections
Connect to the computer. Connect the power cord to the
power outlet. Turn on the printer
power switch.
2002, 2003 by KYOCERA MITA CORPORATION All rights reserved. 2-28, 1-Chome, Tamatsukuri, Chuo-ku, Osaka 540-8585, Japan
Peel off the tapes from the developer units
and remove the protective pad from each
unit.
Close the process frame and then close
the stoppers. Fix the two (A) screws first,
and then fix the two (B) screws.
Secondary
Transfer Unit
Unscrew the four screws. Free the two
stoppers.
Developing
Roller
Black
Cyan
Magenta
Yellow
Process Frame
Printed in Japan 2003.1EC 2CK80011B
For more information about the printer, refer to the Operation Guide (PDF) in the CD-ROM supplied with the printer.
Anchor the secondary transfer unit to the
printer using the included anchor jig and
screw.
Secondary Transfer
Unit Anchor Jig
Remove the 2 tags and then both the
front and rear stoppers.
Ta g
Rear stopper
Front
stopper
Ta g
Parallel Interface
USB Interface
Network Interface
(Ethernet)
15 16 17 18
23 24 25 26
27 28 29 30
31 32 33 34
35 36
19 20 21 22
37 38