L(A)B Life + Beauty PRO-LIFT + User manual

USER GUIDE
PRO-LIFT +

2
L(A)B = Life + Beauty
Is the creation of Oxford University Scientists and Sisters Lauren,
Charlotte and Sophie. L(A)B’s aim is to improve the effectiveness of
your everyday skin and healthcare regimes with cutting edge scientic
developments that t easily into your life.
“As Scientists we wanted to create
apparatus that will improve your
health and beauty routine and give
visible, professional results at home”
- Charlotte & Lauren
L(A)B Founders
For more information on L(A)B visit
www.lab-lifeandbeauty.com

3
PRO-LIFT+
PRO-LIFT+
L(A)B PRO-LIFT+ is a complete skincare solution that can perform
your entire skincare regime and target all your skincare concerns.
With your Pro-Lift+ you can:
Cleanse, Moisturise, Lift + Tone,Treat the signs of ageing and treat
blemishes in one simple, easy to use multi-functional device.
L(A)B PRO-LIFT+ delivers clinically proven results from the rst use

4
1. Titanium metal treatment head use for IONTreatments:
• Cleansing
• Moisturising
• Lifting + Toning
2. Blue LED Light treatment head:
Treats blemishes using blue light at 405-420nm
wavelength, which kills the bacteria that causes
spots.
3. Red LED Light treatment head:
Functions between 630-660nm wavelength
stimulates collagen production and cell reju
venation, helping to give the skin a more youthful
appearance and reduce hyper-pigmentation and
age spots.
3 Treatment Heads:

5
1. CLEANSE:
In cleanse mode, pro-lift+ acts like a magnet to attract impurities, dirt, excess oil and make-up
out of the skin. It does this using galvanic current, a constant stream of positive (+) charges.
This gives a gentle but effective cleanse.
2. NOURISH:
In nourish mode, the galvanic current is reversed to a constant stream of negative (-) charges.
This pushes serums and moisturisers in to the skin giving deeper penetration of nutrients and
active ingredients and increasing skin’s moisturisation.
Galvanic cleansing and moisturising helps to balance out the skin to give you a good skin day,
everyday.
3. LIFT:
In lift mode PRO-LIFT+ uses a tiny electrical current called a micro-current which is made up of
alternating positive (+) and negative (-) charges. Microcurrent lifts and rms the facial muscles
and skin visibly improving facial contour after just one use.
+-+-+-+-+ LIFT MODE
lifts and tones
++++++ CLEANSE MODE draws
impurities out of skin
------ NOURISH MODE pushes ingredients
deeper in to skin

6
Apparatus
L(A)B PRO-LIFT+
Treatment Head
Release Lever
FRONT VIEW BACKVIEW
On/Off Power button
Charging Base
+ Storage Cradle
Treatment head
+/-
treatment button
Level button
DC Input
Conductive
panel
Photofacial button

7
How To Change Treatment Head
Titanium metal
treatment head
Blue and Red LED light
treatment heads
To change treatment heads :
Turn off Pro-Lift+ before changing
heads.
1. Pull the Treatment Head Release
Lever at the back of device and
slide out existing Treatment Head.
2. Slide your desired Treatment Head
into the slot until it is securely
installed and clicks in to place.

8
Regime
You do not need to perform all the treatments every day. and every time you use PRO-LIFT+,
please see below table for use depending on your skin type
Sequence of Treatments
See below the recommended order to perform treatments.You do not need to perform all the
treatments every day. and every time you use PRO-LIFT+
CLEANSE NOURISH LIFT BLUE
LIGHT
RED
LIGHT
ION Treatments -
cleanse & Nourish
& Lift
LED Treatment - Blue
Light
LED Treatment - Red
Light
Everyday
EverydayEveryday
Everyday Everyday Every week Every 3-4 days
Everyday Everyday Everyday
Normal/ Dry/ Aging Skin Oily/ Sensitive Skin
With Spots With Spots
Without Spots Without Spots
During 1st 30 Days of Use
After 1st month of use
1-2 times/ week 1-2 times/ week Once every 2
weeks
Once a week
Ongoing

9
Step 1: CLEANSE
1. Install the metal treatment head.Remove the protective plastic cover from the Ion head before
use.
2. Remove excess make-up and eye make-up.
3. Apply a water based cleanser to the treatment head or to your face as you prefer and
dampen face with water
4. Turn on device by pressing and holding the On/Off power button for 2 seconds until a long
beep sounds.
5. Press the +/- treatment button once so that the CLEANSE light is on.
6. Select level.We recommend you start at high by pressing the level button 3 times until HIGH
light is turned on. If the current feels too strong reduce down from this level by pressing the
level button.
7. Cleanse with Pro-lift+ as you would with your ngers working in gentle rotating and/or lifting
movements over entire face avoid lingering around the eye area. Ensure your nger is in contact
with the conductive panel at all times.
8. After 4 minutes there will be a short short beep and PRO-LIFT+ will go in to standby mode,
ready for the next stage.
9. Rinse off any excess cleanser with water. Do not dry face and proceed to Step 2.

10
Step 2: NOURISH
1. Apply water-based serum, hydrating conduction spray and/ or moisturizer to the face or directly
to the treatment head as you prefer.
2. Press +/- treatment button twice so the NOURISH light is on, then select level as before
3. Work in sections applying enough product to make sure the area being treated is well lubricated
so the treatment head glides easily over the skin. Starting at the base of the neck, moving in
rotating and/or lifting movements work across entire face avoid lingering around the eye area.
Ensure your nger is in contact with the conductive panel at all times.
4. After 4 minutes a short beep will sound and PRO-LIFT+ will go in to standby mode, ready for
the next stage.
5. Do not dry face and proceed to Step 3.

11
Step 3: LIFT
Remove the protective plastic cover from the Ion head before use if not removed previously.
1. Press +/- treatment button 3 times so the LIFT light is iluminated and select level as before.
2. Apply serum and/or hydrating toning spray to the area being treated, we recommend
working in sections to ensure the skin is well lubricated. Most people feel no sensation
when using the Ion head. As long as the lights on the control panel are lit up Pro-Lift+ is
working.
3. Starting at the base of the neck and working upwards and outwards, slowly glide the
treatment head across the face. Ensure your nger is in contact with the conductive panel
at all times.
- Each motion should be steady and take approx 5 seconds moving from the centre of the face
outwards toward the hair line.
- Repeat each position 5 times.
- Avoid lingering around the eye area.
- Use anti-gravity motions, thinking where do you want your face to be!
- For the forehead use vertical motions.
- For stubborn wrinkles you can hold the device in one place for the treatment time.
Keep treatment area well lubricated to ensure treatment head glides over skin at all times by
applying the Conduction toning spray during use as required. See diagram on page 12 and go
online for video clips and more information: www.lab-lifeandbeauty.com
4. After 4 minutes a short beep will sound to signal the end of your treatment.You can do a whole
face in 4 minutes or for a more intensive treatment you can continue to use for up to 20 minutes
a day. If you want to continue, after 4 minutes put back into lift mode and repeat.
For best anti-ageing results use for a minimum of 4 minutes daily for the rst month with L(A)B
Activator serum and Hydrating Toning Spray.

12
Step 3 : Lift
Motions for lifting and toning
Use upward and
outward, anti-gravity
motions

13
Step 4 : Blue LED Light
1. Install Blue LED light treatment head.
2. If you have not already completed steps 1 and 2 remove makeup and cleanse your face, then
towel dry.
3. To turn on Pro-Lift+, press and hold On/Off power button for 2 seconds until a long beep
sounds. Press the Photofacial button.
4. Hold the treatment head in contact with the area of the face to be treated for 3 minutes.
Blue light will be visible on contact with the skin. For effective treatment the treatment head
must be held in constant contact for 3 minutes,do not move/ glide treatment head when using
LED lights.The LED lights do have a natural pulse, this is normal.
5. After 3 minutes a short beep will sound to signal to move to the next position to treat.
You can treat just the areas that suffer from blemishes or are prone to break-outs, or for a
complete facial treatment follow the 6 positions shown in the diagram on page 15, holding the
treatment head in contact with each area for 3 minutes each time.

14
Step 5: Red LED Light Treatment
1. Install Red LED light treatment head.
2. If you have not already completed steps 1, 2 and/or 3 remove makeup and cleanse your face,
then towel dry.
3. To turn on Pro-Lift+, press and hold On/Off power button for 2 seconds until a long beep
sounds. Press the Photofacial button.
4. Hold the treatment head in contact with the area of the face to be treated for 3 minutes. Red
light will be visible on contact with the skin. For effective treatment the treatment head must
be held in constant contact for 3 minutes, do not move treatment head when using LED lights.
5. After 3 minutes a short beep will sound to signal to move to the next position to treat.You can
treat just the areas that suffer from deep wrinkles, hyper-pigmentation and/or ageing, or for a
complete facial treatment follow the 6 positions shown in the diagram on page 15, holding the
treatment head in contact with each area for 3 minutes each time.
Please Note for Photofacial treatments:
-The LED lights do have a natural pulse, this is normal.
- Blue and Red LED light treatment heads are installed with contact sensors and will only illuminate
when in contact with the skin.
- The POWER LEVEL Button is disabled when using LED light treatment heads
- If not used for 3 minutes the PRO-LIFT+ wil return to standby mode and will automatically turn
off after a further 4 minutes.
- During Photofacial Treatments, contact with the Conductive Panel is NOT necessary.
- If contact is lost with skin during the 3 minutes the timer will reset and the short beep will not
sound until a full ongoing treatment of 3 minutes is completed.

15
Positions for Blue and Red LED Light
Treatment Heads
Forehead and Number 11’s
Laughter lines, Crow’s feet
Marionette Lines, Corners of mouth
and jowels
Naso-lobial lines and Periorial
wrinkles

16
General Information
To turn on : press and hold the Power Button for 2 seconds until a long beep sounds.
Once turned on, Pro-lift+ is in standby mode and will automatically turn off if left unused for 4 minutes.
Pro-lift+ returns to standby mode whenever you uninstall a treatment head.
Most people feel no sensation when using the Ion head.As long as the lights on the control panel are
lit up Pro-Lift+ is working.
Remove the protective plastic cover from the Ion head before use.
At any time during treatment with the metal treatment head you may switch between CLEANSE,
NOURISH and LIFT treatments by pressing the ION Treatment Button, or between power levels by
pressing the POWER LEVEL button.
Turn off Pro-Lift+ before changing heads.
When using the metal treatment head always retain contact with the conduction panel. Do not rub
or press treatment head hard against the skin as this may cause damage or irritation.Always ensure
skin is moistened with water-based skincare products.
You might feel a slight tingling“electrical” sensation during use. It is a normal sensation and will not harm
your skin.If you experience this ensure skin is well lubricated with L(A)B Activator serum, moisturiser
or toning spray (or other water-based skincare product).
The LED lights do pulse, this is normal.
For best results use with L(A)B Skincare: Cleanser, Moisturizer,Activator Serum and Hydrating Toning
Spray. If using other skincare ensure it is water-based (check Aqua is one of the ingredients).If in doubt
contact L(A)B: [e-mail]

17
How to Charge your Device
Depending on the number and length of treatments carried out, a full charge of Pro-Lift+ will last 2-7 days
1. The Power indicator light ashes red when the battery runs out.
2. Put device in charging cradle and connect adaptor to the DC input at the back of stand.
3. Plug the adaptor into the mains electrical output
4. The power indicator red light stays lit when charging is in process.
5. The whole charging process takes approximately 3 hours.
6. The power indicator red light turns off when battery is fully charged.
Please note:
The battery comes with an adequate amount of power upon production so you may use the device
immediately after purchase. The power indicator red light will start ashing to indicate the device
requires charging.
Avoid charging the device without exhausting the battery, always start charging after the battery has
run out.
The power sensor is a sensitive component, the slightest change of power storage within the
battery after it is fully charged might cause the power indicator red light to turn on or off at
different stages of charging.This is normal and should not be considered as a system defect.This will
not happen if device is charged ONLY after battery is fully exhausted.
Care and Maintenance
1. Wipe device with clean,moist towel/ anti-bacterial wipe after each use.Towel dry afterwards.
We recommend using a L(A)B UV Sanitizer to kill 99.9% of bacteria in between uses.
2. Do not submerge the device directly in water or any other cleaning agent.
3. Store device and charging unit in a cool dry place.

18
Warranty
L(A)B Pro Lift + is under warranty for two years following purchase under normal usage when
purchased from an authorised retailer. Please retain your receipt to validate you warranty.
Please contact us to register your Pro Lift + or if your Pro Lift + becomes defective at:
[e-mail]
This warranty does not cover products damaged by the following:
Accident, misuse, improper care or commercial use
Servicing by unauthorised persons or alteration
Use with incorrect current or voltage
Any other conditions beyond our control
Use with incorrect skincare products
Medical Precautions
- If you experience any adverse reaction stop using Pro Lift+ and contact your doctor immediately
- Do not use on skin that is burnt, infected or on open wounds, eczema or tumours
- Do not use on children
- Pro Lift+ is not intended for use by persons (including children) with reduced physical, sensory
or mental capabilities, or lack of experience and knowledge
- Do not use on Eyelids or Mucous membrane (inside of mouth)
- If you have undergone cosmetic or any other surgery including metal implants e.g pace-maker
consult your doctor prior to use
- If you are pregnant consult your doctor prior to use
- Use gently and as instructed
- Do not use if you suffer from photo sensitive reactions
- Do not look directly into the LED lights when lit
- Do not shine LED lights directly into someone else’s eyes

19
Safety Precautions
- Read all instructions prior to use
- Use as directed by these instructions
- Keep out of reach of children
- If you experience any issues with Pro Lift + contact L(A)B do not dismantle or repair the device
yourself
- Use only the correct L(A)B parts and accessories with this device including charger and
attachments
- Do not scratch or damage the attachment heads
- Do not use the device if it has a damaged plug or cable - contact L(A)B for assistance
- Always place L(A)B Pro Lift+ in charging base prior to plugging in to charge
- Do not use L(A)B Pro Lift+ whilst in charging base or plugged into mains
- Always turn off charging base once fully charged
- Keep adaptor and Charging base away from water, if they drop into water turn off power
immediately and before touching the units
- Keep device away from ammable aerosol products or where Oxygen is being administered
- If device fails to work contact L(A)B for advice
- If Charger and/ or adaptor overheat contact L(A)B for replacements
- Failure to use and/ or maintain the device in accordance with these instructions will invalidate
the warranty.

20
L(A)B DEVICE DRIVEN SKINCARE
L(A)B have created a range of skincare formulated and made in England to be used alone or with
L(A)B Devices to enhance their performance and deliver the most advanced results.
L(A)B Activator Serum, Moisturiser, Cleanser and Hydrating Toning Spray
Include ingredients such as:
Collagen
Hyaluronic Acid
Seabuckthorn
Rosehip Oil
Aloe
Cucumber