L.A. Baby Juvenile Products DRW-5 User manual

Parts List Pieces per Unit
A - Drawer back 1
B - Drawer side - right 1
C - Drawer side - left 1
D - Drawer bottom 1
E - Drawer front 1
G - 1
K - Machine bolt 20 m/m
F - Drawer track (pre-installed) 2
Drawer hanger - left
H - Drawer hanger - right 1
I - Case track (pre-installed) 2
J - Wood screw 32 m/m 4
4
L - Wood screw 13 m/m 4
M - L-Bracket 2
N - Machine bolt 45 m/m 4
O - Washer 4
P - Nut 4
Q - Allen wrench 1
R - Open end wrench 1
1
Care Instruction:
Your drawer may be cleaned,
using a damp cloth and ordinary
mild domestic detergent. Do not
use abrasives or bleach.
Air dry.
L.A. Baby Juvenile Products
16039 Loukelton Street
City of Industry, California 91744
Toll free customer service: 800-584-3094
e-mail: [email protected]
www.lababyco.com
Under Drawer
For Window Crib Model #510 & 530
Model DRW-5 (LB)
A
F
B
D
E
C
K
J
O
H
G
I
Ins_DWR-5_032311
DATE OF MFG
Model: DRW-5
Made In China
Tools required: Phillips head screw driver
Allen wrench (Included)
Open end wrench (Included)
M
L
P
N
Q
P

C
A
Fig. 2
Tighten the four wood screws (K)
on drawer back (clock wise) with a
Phillips head screw driver (Fig. 3)
2
Drawer Assembly
B
Drawer Back
1. Align dowels of drawer back panel(A) into pre-drilled holes on left drawer side
panel (C) .Make certain that the slot on bottom of the panels lines up evenly. (Fig.
1)
2. Insert 2 wood screws (J) into drilled holes on outside of left panel (C ).
3. Repeat this procedure for the right side panel (B). (Fig. 2)
B
A
C
Fig. 1
A
Drawer Back

Slide the drawer bottom (D) along
the slotted edges of the left and
right drawer sides to the slotted
edge of the drawer back. (Fig. 3)
Attach the drawer face (E) by
aligning the drill holes on the back
of the face to the plastic “bosses”
on the ends of the side panels (C
& B). (Fig. 5)
Insert machine bolt (K) through
lower boss and insert it into
receptor on rear of face panel (E)
Partially tighten the screw and
repeat procedure for three
remaining bosses. Complete
tightening the screws with phillips
head screw driver (Fig 5).
Attach the L-Bracket (M) onto the
back of the front drawer face (E )
(Note pilot holes) and onto the
right and left drawer sides B & C
(Note pilot holes) using the
screws (L). Tighten with phillips
head screw driver (Fig 6 & 8)
E
Fig. 3
Fig. 4
Fig. 5
Fig. 6 Fig. 7
3
Drawer Front
E
B
L
Drawer Front
Drawer Front
Bosses
M
K

Attaching the Drawer Hangers
We suggest you lay your crib up side
down for easy assembly.
Place the left (G) and right (H) Drawer
Hangers with the tracks facing each
other along the lower horizontal of the
end panels as illustrated. (Fig. 8)
Align the four pre-drilled holes of the
Drawer Hangers and the four pre-
drilled holes on the lower horizontal of
the end panels. (Fig. 9)
Attach the Hangers using Bolts (N),
Washers (O) and Nuts (P) on all four
locations using a phillips head screw
driver. Place a washer (O) next to the
nut and bolt as illustrated (Fig. 9)
Make sure all four bolts and nut
fasteners are tight using the allen
wrench (Q) and open end wrench (P).
Return your crib to a right-side- up position.
Gently slide in the drawer.(Fig. 10)
G
HFig. 8
NOP
Fig. 9
Fig. 10
4
H
Front of crib