La Crosse Technology WS-9626U-IT User manual

WS-9626U-IT
915 MHz WIRELESS WEATHER STATION
POSTE MÉTÉO SANS FIL 915 MHz
Instructi n manual
Manuel d'lnstructi ns

1
Contents
Language Page
_________________________________________________________________________________
English 1
French 56

2
TABLE OF CONTENTS
Topic
Page
Inventory of Contents
4
Features
5
Setting Up
8
Battery Installation
12
Function keys
15
LC Screen and Settings
17
Atomic auto-set time - WWVB Radio Controlled Time 20
Manual Settings 21
Weather Forecast and Tendency 31
isplay of Indoor Temperature and Humidity Reading 37
isplay of Outdoor Temperature Reading 38
isplay of Indoor Maximum and Minimum records 39
isplay of Outdoor Maximum and Minimum records 40

3
aily Min and Max outdoor temperature display 43
915 MHz Reception 44
Mounting 45
Care and maintenance 50
Specifications 51
Warranty 53
This product offers:
INSTANT TRANSMISSION
is the state
-
of
-
the
-
art
new wire ess transmission techno ogy, exc usive y
designed and deve oped by LA CROSSE
TECHNOLOGY. INSTANT TRANSMISSION offers
you an immediate update (every 4 seconds!) of a
your outdoor data measured from the transmitters:
fo ow your c imatic variations in rea -time!

4
INVENTORY OF CONTENTS
1. Wireless Weather Station
2. Wireless Temperature Sensor (TX29U-IT) and mounting bracket.
3. Instruction Manual and Warranty Card.
4. 4 Fresh “AA” IEC LR6, 1.5V Alkaline Batteries.

5
LC
isplay
FEATURES:
The Weather station
Foldout
Stand
Battery
compartment
cover
Function
Keys
Hanging hole

6
• Atomic auto-set time (WWVB Radio controlled time) function with manual setting options
• Atomic auto-set time reception ON/OFF setting
• 12/24 hour display
• aylight time saving ON/OFF
• Hour, minute and second display
• Time zone option ±12 hours
• Wireless transmission at 915 MHz
• Signal reception intervals at 4-second
• isplay indoor and outdoor temperature (°F or °C) and indoor humidity (% RH)
• Weather forecasting with 15 easy-to-read weather forecast signs featured by
weather man
• Weather forecasting icon sensitivity setting
• Temperature display in degrees Fahrenheit (°F) or Celsius (°C) selectable
• Indoor and Outdoor temperature display with MIN/MAX recording
• All MIN/MAX outdoor recordings show date and time received
• isplay aily Minimum and Maximum Temperature of outdoor channels
• All MIN/MAX recordings can be reset

7
• Can take up to three outdoor transmitters
• LC contrast setting
• Low battery indicator
• Table standing/ Wall mounting
The Outdoor Temperature Transmitter
• Remote transmission of outdoor temperature to Weather Station by
915 MHz
• Shower proof casing
• Wall mounting case
• Mounting at a sheltered place. Avoid direct rain and sunshine

8
SETTING UP:
When one transmitter is to be used
1. First, insert the batteries into the Temperature transmitter. (see “Insta and rep ace batteries
in the Temperature transmitter“).
2. Immediately after and within 30 seconds, insert the batteries into Weather station (see “Insta
and rep ace batteries in the Weather station”). Once the batteries are in place, all segments
of the LC will light up briefly. Following the time as 12:00 and the "weather man" icon will be
displayed. If these are not displayed after 60 seconds, remove the batteries and wait for at least
10 seconds before reinserting them.
3. After inserting the batteries into the transmitter, the Weather station will start receiving data
from the transmitter. The outdoor temperature and the signal reception icon should then be
displayed on the Weather station. If this does not happen after 3 minutes, the batteries will
need to be removed from both units and reset from step 1.
4. In order to ensure sufficient 915 MHz transmission however, this should under good conditions
be a distance no more than 100 meters between the final position of the Weather Station and
the transmitter (see notes on “Mounting” and “915 MHz Reception”).

9
Note:
The indoor receiver registers the temperature by defau t in Farenheit (°F), but user can manua y
set to Ce sius (°C) ONLY after the initia set-up is comp ete as instructed in the manua . After the
LCD shows the temperature readings from the outdoor transmitter, user may set the
temperature unit to °C (See Manua Settings be ow).
When more than one transmitter is to be used
1. User shall remove all the batteries from the temperature station and transmitters and wait 60
seconds if setting has been done with one transmitter before.
2. Insert the batteries to the first transmitter.
3. Within 30 seconds of powering up the first transmitter, insert the batteries to the Weather Station.
Once the batteries are in place, all segments of the LC will light up briefly. Following time as
12:00 and the weather man icon will be displayed. If they are not shown in LC after 60 seconds,
remove the batteries and wait for at least 60 seconds before reinserting them.
4. The outdoor temperature from the first transmitter (channel 1) should then be displayed on the
Weather station. Also, the signal reception icon will be displayed. If this does not happen after 2
minutes, the batteries will need to be removed from both units and reset from step 1.