La Crosse WS-6010U User manual

1
Wall Mount
Location
Solar panel
Battery
compartment
Model WS-6010U
Solar Station
QUICK SETUP GUIDE
Solar-powered Transmitter:
Remote transmission of outdoor temperature and humidity to the
Solar Station by 915 MHz signals
LCD will automatically alternate and display the outdoor
temperature and humidity data
Recharge batteries by solar-powered cells
Wall mounting case
Notes:
Solar panel

2
The solar-powered temperature transmitter uses solar cells to charge the rechargeable
batteries (2 x AAA rechargeable batteries; included).
The rechargeable batteries cannot be replaced.
SOLAR TRANSMITTER OPERATION MODES
Important:
Users need to press the reset key to activate the solar transmitter and link the
transmission to the Solar Station (receiver).
It is important to allow sufficient light to reach the solar panel while activating the solar transmitter.
Make sure the lights are on in the setup room and the solar panel is facing a 60W light bulb or
brighter - do not cover with hands or other objects.
Solar transmitter RESET key:
The solar transmitter has 3 operations modes:
Normal Operation Mode:
This mode occurs when the battery voltage is higher than 2.5V.
The transmitter will measure and transmit the temperature and humidity data to the Solar
Station every 8 seconds.
The environment brightness is checked every 5 seconds
If a dark environment is detected, it will measure and transmit the temperature every 16s.
If the battery voltage is dropped lower than 2.8V, it will measure and transmit the
temperature every 16s
If battery voltage is dropped lower than 2.4V, will go into Idle mode.
Note: only use a small pointed pen to
press the RESET key to re-active the
transmitter into Normal Operation Mode.
RESET key

3
If the solar transmitter is placed into a dark environment for 72 hours, will goes into Stop
mode.
If the user cover the solar cell for 10 seconds and press the reset button, "StP" will be
displayed on the LCD. Then the transmitter enters STOP mode.
Idle Operation Mode:
This mode occurs when the battery voltage drops lower than 2.4V.
LCD is turned off.
Does not perform temperature measurement and transmission.
The environment brightness is checked every 5 seconds.
If battery voltage is raised higher than 2.5V, the unit will go into Normal mode.
If the solar transmitter is placed into a dark environment for 72 hours, the will go into Stop
mode.
Stop Operation Mode:
This mode occurs when the solar transmitter is placed into a dark environment for 72 hours
or the user covers the solar cell for 10 seconds and presses the RESET button.
The transmitter is in a standby state. The does not perform any operations and the LCD is
off.
Under a bright condition, press the reset button to wake up the transmitter into normal
operation mode (battery voltage is higher than 2.5V).
This is the most power saving mode.
TO INSTALL / REPLACE BATTERY IN THE SOLAR STATION
The Solar Station can use either the included 2 x alkaline rechargeable batteries (charged by
solar panel; included) or 2 x AA alkaline battery (non-rechargeable; not included).
INITIAL SETUP
It is very important to follow these steps:
1. First, remove the label covering over the battery compartment on the back.

4
2. Open the battery compartment, and MAKE SURE that the battery switch is in the
BATTERY position (not the SOLAR position).
Battery switch in the BATTERY position
3. Now locate the battery insulator tab, and gently pull to remove it.
4. Slide the battery switch to the SOLAR position
5. Battery switch in the SOLAR position
6. Continue to section titled “Setup After Changing/Installing the Battery in the Solar
Station”
TO INSTALL / REPLACE BATTERIES
The included alkaline rechargeable batteries should provide you with many years of service. If
your batteries need to be replaced, we suggest you use 2 fully charged the AA Alkaline.
Rechargeable batteries should be fully charged before inserting into clock. Alkaline
rechargeable batteries must be used.
If you choose to use non-rechargeable batteries, the battery switch MUST be moved to the
BATTERY position (not the SOLAR position). In this position, the solar cells do not charge the
batteries.
REGARDLESS OF THE TYPE OF BATTERIES INSTALLED, THE BATTERY SWITCH MUST
BE IN THE BATTERY POSITION WHEN THE BATTERIES ARE INSERTED.
If rechargeable batteries are used, the Battery switch should be moved to the SOLAR position
AFTER it is has been inserted.
To use non-rechargeable alkaline batteries:
1. Remove the included rechargeable AA batteries from the compartment.
2. Use the switch to select the alkaline battery (see below).
3. Insert the batteries into the compartment, observing the correct polarity (see marking inside
battery compartment.
4. Replace battery cover

5
Note: For best performance, batteries should be replaced at least once every 2 years to maintain
the best running accuracy. Ensure that the batteries used are new and the correct size.
Use switch to select
which type of batter
y
will be used before
inserting the batter
y
into the compartment

6
Please help in the preservation of the environment and return used batteries to an
authorized depot.
SETUP AFTER CHANGING/REPLACING THE BATTERY IN THE SOLAR STATION
1. After powering up the Solar Station, all LCD segments will light up briefly and it will show
the time (12:00), indoor temperature, date, and indoor humidity.
2. After the batteries are inserted, the Solar Station will start receiving data signal from the
solar transmitter. The outdoor temperature and humidity data should then be displayed on
the solar station. If this does not happen after 2 minutes, the batteries will need to be
removed from both units and reset from step 1.
3. The distance between the Solar Station and the transmitter should not be more than 200
feet (60.96m) to ensure sufficient 915 MHz transmission. (see notes on “Positioning” and
“915 MHz Reception”).
Note: When changing the batteries:
1. Be careful that they do not spring free from the contacts.
2. Press any button 20 times with the batteries removed.
3. Always wait at least 10 minutes after removing batteries before re-inserting; otherwise
start up problems may occur.
TO SET THE TIME
Note: The time will be displayed with “AM” or “PM”for the time from 12:00 noon until 11:59.
1. Press and hold the SET key for 3 seconds to enter the time setting mode.
Rechargeable Alkaline
battery switch position
Primary Alkaline
battery switch position

7
2. The hour digits will start flashing.
3. Set the desired hours by pressing and releasing the +key followed by pressing the SET
key.
4. Now the minute digits will start flashing.
5. Set the desired minutes by pressing and releasing the +key. If the +key is held, the units
will increase by 5.
6. Press the SET key again to confirm and enter the Solar Mode setting.
SOLAR MODE
The Solar Mode is used for saving the power consumption of the rechargeable battery (Default
setting ON):
1. The characters “ON” or “OFF” will start flashing. By use of the +key select “ON” or
“OFF” to set the solar mode.
2. Press and release the SET key to exit the setting mode and switch back to the normal
display mode.
If the solar mode setting is ON:
The surrounding environment brightness is checked every 5 seconds.
LCD will automatically turn OFF if the environment is too dark.
LCD will automatically turn ON if the environment is bright enough.
No information will be displayed when the LCD is OFF, but all the settings and
operations will remain, except for the temperature and humidity measurements.
If the solar mode setting is OFF:
LCD will remain ON constantly.
STOP MODE
If the Solar Station is placed in a dark environment for 72 hours continually, the clock will go to
the stop mode:
The most power saving condition.

8
The Solar Station will not perform any operation and the LCD will also be OFF.
Press any key to wake up the Solar Station and to re-activate the transmission with the
solar transmitter.
MIN/MAX: Press and release the PLUS button to view:
Outdoor Temperature minimum and maximum.
Indoor temperature minimum and maximum.
Current display.
RESET MIN/MAX: Press and hold the PLUS button for 10 seconds to reset the
indoor and outdoor minimum and maximum temperatures to current temperatures.
DISPLAY MODES: Press and release the SET button to view
Shows outdoor temperature in the first line on the left side and outdoor
humidity in the second line on the left side. Shows indoor temperature in
the first line on the right side and indoor humidity in the second line on the
right.
Shows outdoor temperature in the first line on the left side and outdoor
humidity in the first line on the right side. Shows indoor temperature in the
second line on the left side and indoor humidity in the second line on the
right side.
Shows indoor temperature in the first line on the left side and indoor
humidity in the first line on the right side. Shows outdoor temperature in the
second line on the left side and outdoor humidity in the second line on the
right side

9
915MHZ RECEPTION CHECK FOR OUTDOOR SOLAR TRANSMITTER
The Solar Station will receive the outdoor data every 48 seconds. If the temperature data is not
being received 2 minutes after setting up (or the display shows “- - -”), then please check the
following points:
1. The distance of the Solar Station or outdoor transmitter should be at least 6 feet (2 meters)
away from any interfering sources such as computer monitors or TV sets.
2. Avoid placing the receiver onto or in the immediate proximity of metal window frames.
3. Using other electrical products such as headphones or speakers operating on the same
signal frequency (915MHz) may prevent correct signal transmission and reception.
4. Neighbors using electrical devices operating on the 915MHz signal frequency can also
cause interference.
Note: When the 915 MHz signal is received correctly, do not re-open the battery cover of the
Solar Station, as the batteries may spring free from the contacts and force a false reset. Should
this happen accidentally then reset all units (see “TO INSTALL / REPLACE BATTERY IN THE
SOLAR STATION” and “INITIAL SETUP” above) otherwise transmission problems may occur.
The maximum transmission range is 200 feet (60.96 m) from the outdoor transmitter to the Solar
Station (in open space). However, this depends on the surrounding environment and interference
levels. If no reception is possible despite the observation of these factors, all system units have to
be reset (see “TO INSTALL / REPLACE BATTERY IN THE SOLAR STATION” and “INITIAL
SETUP”).
POSITIONING THE SOLAR STATION:
Before permanently mounting, ensure that the Solar Station is able to receive 915MHz signals
from the desired location. In addition, the Solar Clock should be placed in a bright environment for
the rechargeable batteries to be able to recharge.
There are two possible ways to mount the solar station:
Table Stands
Wall Mounting
WALL MOUNTING

10
1. Install a mounting screw (not included) into a wall—leaving approximately 3/16 of an inch
(5mm) extended from the wall.
2. Place the Solar Station onto the screw, using the hanging hole on the backside. Gently pull
the Solar Station down to lock the screw into place.
Note: Always ensure that the Solar Station locks onto the screw before releasing.
POSITIONING THE SOLAR TRANSMITTER:
It is important to place the solar transmitter in a bright environment for the
rechargeable batteries to be able to recharge.
The solar transmitter can be placed onto any flat surface or wall mounted using the
bracket which doubles as a stand or wall mount base.
To wall mount: Secure the bracket onto a desired wall using the screws and plastic
anchors.
Clip the solar transmitter onto the bracket.
Note: The mounting surface can affect the transmission range. If, for instance, the
unit is attached to a piece of metal, it may then either reduce or increase the
transmitting range. For this reason, we recommend not to place the unit on any metal surfaces or
in any position where a large metal or highly polished surface is in the immediate vicinity (garage
doors, double glazing, etc.). Before securing in place, please ensure that the Solar Station can
receive the 915MHz signal from the solar transmitter at the positions that you wish to place them.
WARRANTY INFORMATION
La Crosse Technology, Ltd provides a 1-year limited warranty on this product against manufacturing
defects in materials and workmanship.
This limited warranty begins on the original date of purchase, is valid only on products purchased and
used in North America and only to the original purchaser of this product. To receive warranty service, the
purchaser must contact La Crosse Technology, Ltd for problem determination and service procedures.
Warranty service can only be performed by a La Crosse Technology, Ltd authorized service center. The
original dated bill of sale must be presented upon request as proof of purchase to La Crosse Technology,
Ltd or La Crosse Technology, Ltd’s authorized service center.