LAIA B&H User manual

Thank you for purchasing the B&H PC Pro Wifi (here in after referred to as
"this product"). This user manual describes how to use this product and
precautions for safe handling. Please read carefully before use. Please keep
this user manual in a safe place even after reading it.
Please be careful not to put this product to children’s mouth.
▲ It may cause injury to children or malfunction of this product.
Do not open or disassemble the cover of this product.
▲ It may cause a malfunction or electric shock.
Do not touch the product or cable with wet hands.
▲There is a risk of electric shock when this product is connecting to a comp-
uter.
Do not allow foreign substances such as liquids and metals to get inside the
product.
▲It may cause electric shock, fire or malfunction.
Do not install or store this product in a place with high humidity or humidity,
in direct sunlight, in a place with a lot of dust or oily smoke, in a car or near
a heater, or in a hot place.
▲It may cause a malfunction or electric shock.
Avoid this product to strong vibration or impact.
▲It may cause malfunction or damage.
Do not stack this product on top of each other or place heavy objects on top
of this product.
▲It may cause a fire or malfunction.
Do not install or store this product in an unstable place.
▲Dropping may cause malfunction or damage.
When connecting or disconnecting the cable of this product, be sure to hold
the connector part and do not apply excessive force.
▲It may cause malfunction or damage.
Before cleaning this product, disconnect the cable of this product from your
Power source.
▲It may cause electric shock or malfunction.
When cleaning this product, do not use it that contains volatile organic
solvents such as benzine and thinner.
▲It may damage the paint or cause a malfunction. Wipe dry with a soft,
dry cloth.
(1) It is prohibited to copy or reprint a part or all of this manual without per
mission.
(2) The Company shall not be liable for any direct or indirect damage caused
by the failure of this product or its use. Please note.
(3) We do not guarantee the loss or damage of data or programs that occur
while using this product. Please note that. Take measures such as taking
regular backups.
(4) This product is made for only in our self country. We are not responsible
for any use outside of our country.
(5) The images on the screen described in this manual may differ from the
actual ones.
(6) If you find any suspicious points, mistakes, omissions, etc. regarding the
contents of this manual, please contact the store where you purchased the
product or us.
Details of harm that may cause death or serious injury
to the person.
Please pay attention to the content.
Contents that may cause injury or property damage to
people! Contents that you should be careful about.
Precautions for safe use (be sure to observe)
This product is incorporated and used in medical equipment, nuclear equip-
ment, aerospace equipment, transportation equipment and other life-threa-
tening equipment as well as equipment and systems that require a high
degree of reliability . We are not responsible for any personal
injury or social injury caused by using this product for these purposes.
Do not touch the product or cables while thundering.
▲ There is a risk of electric shock due to a lightening strike.
Since this product is powered by electricity, there is a risk of ignition. If smoke
or a strange odor is emitted, turn off the power of this product and the con-
nected PC or device.
▲ It may cause a fire depending on the environment in which this product
is installed.
Do not step on the cable of this product with furniture or pinch it with a door.
Also, do not pull or bend the cable.
▲ It may cause a fire or malfunction.
It is a 2.4GHz B&H PC Pro Wifi that does not require a cable connection.
It can be used even at a distance of about 20m in a straight line.
The range of use varies greatly depending on the environment.
It has a built-in lithium-ion battery and can be used continuously for about
3 hours on a single charge.
It can be used while charging with a small charging cable, so there is no need
to worry about running out of battery.
It supports USB video protocal (UVC), so no driver is required. All you have
to do is connect the receiver to your computer and it will work.
Built-in tripod hole for camera. It can be attached to a commercially available
camera tripod.
Video works smoothly with USB 2.0.
It supports various video chats such as Zoom, Microsoft Teams and Skype.
Before using, please make sure that you have all the stuff in the pack list.
If you find something missing, please contact your seller.
The contents of this user manual are subjected to change without notice.
Design and specifications for improvement are subjected to change without
notice.
We guarantee the quality of this product only when it is used under normal
conditions within the warranty period and warranty conditions of the B&H
range. Please check for more details on Warranty in our website.
Warranty provisions
Meaning of icon
Warning
Warning
Attention
Attention
2.Charging cable x 1pc
4.User manual x1 pc
Please check first
Pack List
1.B&H PC Pro Wifi x 1pc
3.USB Receiver x 1pc
1. Features
If you use a router or firewall to connect to the Internet, you may
not be able to use Internet-based functions such as video chat.
We only supply the webcam itself. We do not supply any video
conference software such as Zoom, Microsoft Teams or Skype.
Mic quantity 1
MIC ArrayForm Electret microphone
SNR 58dB
Sensitivity -42dB
Far-field Distance 0-3 meters
Horizontal Voice pickup Horizontal 180°
Input Voltage USB 5V
Working Current 450mA-800mA
Storage Temperature and -10℃~+60℃/20%-95% Humidity
Working Temperature and -10℃~+50℃/20%-80% Humidity
Operating Enviroment Indoor
OS Win / Vista / Linux / MAC / Android
Size 75 x 62 x 79 mm
Weight 142g
Video Interface USB2.0
Field of View
Resolution
None
Diagonal:81.3°，Horizontal：68.9º
1920*1080@30fps,1280*720@30fps
Imaging Sensor 1/2.9 inch CMOS Sensor
Total Pixels 2.0 million pixels
Output Image Format MJPG，H264，YUY2
Focal Length f=3.9±5% mm
Minimum Illumination 0.5Lux
Focus Mode Fixed Focus
Image Color 24Bit
Aperture Pattern Fixed
Picture Adjustment
B&H PC Pro Wifi
2. Product Specification
3. Names and functions of each part
B&H PC Pro Wifi
(2). USB Receiver
Lens
3 ways of placing
It is a lens that captures an image.
(1) Place on desk
(2) Clip on monitor
(3) Attach into tripod.
Camera(TX modules )
Red LED
Charging
Below is the contents of how to use the device
Lighting
Slowly flash
Fastly flash
Low battery Disconnected
Pairing Pairing
Disconnected
Connected Connected
Green LED Green LED
USB Unit(RX Modules)
Type-C port for charging
You can charge it by connecting the
included cable.
It can also be used while charging.
Tripod hole
A tripod can be attached.
Rotate up / down / left / right
The head part can move up and down 90°
left and right 360.
Red LED
Green LED
Pairing Button
Up and down 90°
360 ° left and
right
Windows 11/10/8.1/8
The following conditions are required for using this device.
Intels@CoreTM i3 1.2GHz or above 2GB or above
Memory 2GB or above
3.Hard disk 2GB or above
4.One free space USB port
Supported OS
System requirements
Mac OS 12/11
Mac OS 10.12~10.15
Power on/off
You can turn the power button
on and off.
B&H PC Pro Wifi
Pairing
button
Pairing has
done at the
factory. But if
the pairing is
disconnected,
you can
re-connect.
Microphone
Pick up the sound.
laia
laia
laia

4. How to use 5. How to check if this product is recognized correctly
6. How to re-connect 7. FAQ
1. Charge
2. Install the camera
3. Connect the camera 4. Turn on the camera
This product is a high power device.
Connect the USB connector of the receiver to the USB
port of your computer.
The driver will be installed automatically.
The installation status is displayed in the task tray during
installation.
After connecting the receiver to your computer,
press the power button on the webcam body.
<Camera automatic power off function>
If you turn off your computer while the camera is on, the camera will automatically turn off.
If the charging cable is connected to the camera and power is supplied, the camera will not turn off.
The green LED on the webcam body and the
green LED on the receiver will light up.
The webcam is now ready for use.
With the webcam turned on Press and hold the
power button. The power of the webcam will be
turned off.
If the green LED on the webcam body and the green LED on the receiver are blinking,
the receiver may not be connected properly or may not be paired.
Make sure the receiver is connected to your computer.
Pairing is completed at the time of shipment from the factory. If the pairing of the
camera is disconnected, please reconnect from "6. How to reconnect ".
Since this product is a wireless connection, a wired
connection is not possible.
Cannot be connected using the included USB cable
USB Port USB side
Power
button Green LED
Receiver
It does not work properly.
Do not connect to USB hub without AC adpater
Connect it directly to your computer or to a USB hub with an AC
adapter.
With the webcam turned on, press and hold the power button, the
power of webcam will be turned off.
Before installation
Place this product on the
monitor of laptop/PC
Adjust the mount as per the
thickness of a laptop/PC/Screen
From Windows start
Select all apps
1. Click Windows Start to display the Start screen.
Camera icon
Arrow arrow
icon
Camera icon
Camera switching
2-1.The screen on the right is
displayed Click the camera icon.
If the icon is not displayed,
click the arrow icon to display
the list of apps.
2-2. Click the camera icon
from the app list
3. The image of the webcam is projected.
If multiple cameras are connected and the image of this product is not displayed,
Right-click the screen to display the setting screen.
Click "Switch Camera" to change the camera.
1. Click Windows Start and click "Camera"The image of the webcam
is projected.
2. When multiple webcams are connected and the image of this
product is not displayed Click "Switch Camera" to change the
camera.
Switching cameras
1. Start 1.0S and in the application folder
Launch Face Time!
The pairing was completed at the factory, but if the camera is out of pairing, you can
re-connect it.
1. turn on the power of the camera
The green LED on the camera body flashes
slowly. (If it is lit, which means it is already
paired)
Q1: Is it compatible with Zoom, Microsoft Teams and Skype?
A1: Compatible.
Q2: I want to use it for video conferences at my company?
A2: Many companies use firewalls when connecting to the
Internet, so they may not be available for video conferences.
Please contact the server administrator for details.
Q3: The image does not move smoothly?
A3: It depends on the performance of your computer and
the speed of your internet connection.
Q4: I want to test whether the camera is working?
A4: Please refer to "5. How to check if this product is
recognized correctly".
2.Press the pairing button on the camera
body. The green LED flashes quickly.
3. Connect the receiver to your computer.
Make sure the green LED on the receiver is
blinking and press the pairing button on
the receiver
4. Green LED on the camera body and
receiver Green LED lights up
This completes the pairing.
Power button Pairing button
Pairing button
Green LED
Green LED
2. From "Video", choose the webcam model
of this product
Model of product
3. The image taken with this product is displayed on
the preview screen.
Camera
Click Camera
Attach the camera screw of the tripod to the tripod hole on the
back of the stand.
How to install on a tripod * Tripod is not included
For Windows 11 Switching webcam for Windows 8.1-8
For Windows 10
For Mac
When using for the first time, charge until the red LED turns off.
Be sure to charge with the included USB cable for charging.
Connect the charging USB cable to the charging port of the
webcam as shown on the right. Laptop
USB Port AC Adapter
USB side
Charing
Type-C Side
Red LED
Connect the USB cable for charging to your computer
or AC charger-adapter. LED light turns ON during charging.
Charging time is about 3 hours. When the battery is full charged,
the red LED light turns OFF
Side of
Monitor
Side of
Monitor
When installing on a laptop,please take care
not to damage the monitor
Clip
1/4 "Screw
CMS-STN1BK
Tripod
Tripod
hole Back
laia
laia