Lakeland Mills ALQ60 Queen Log Bed User manual

ALQ60 Queen Log Bed
ALK76 King Log Bed
Please check contents before assembly. If any items are missing or damaged, do not take the unit back to the store.
Call 1-800-427-5136 for customer service and we will save you time by correcting any problems directly for you.
BED COMPONENTS
3 - Mattress Supports
4 - Angle Braces
3 - Mattress
Support Feet
2 Each - Head
& Footboard
Legs
Legs are drilled as
lefts and rights.
1 Each - Assembled Head/Foot 2 - Bed Rails
NOTE: Cracks or Checks in logs are part of the
natural beauty of cedar logs and should not be
considered defects.
NOTE: Read all instructions before starting.
HARDWARE & TOOLS REQUIRED
25 - 2 1/2” Screws
4 - 1/4” x 5” Hex Washer Head Screws
4 - 5/16”
washer
Rubber
Mallet
Hammer
& Block
of Wood
7/16” Socket
or Wrench
#2 Phillips
Screwdriver
or
or
or
HELPFUL TIPS:
 Using a battery operated or electric drill will make assem-
bly faster and easier.
 If finishing yourself, tape off all doweled ends. (Finishes
may cause dowels to swell, making assembly difficult.).
STEP 1
STEP 2
Assemble headboard by laying long headboard legs and one
assembled Head/Foot board on a clean flat surface, with lower
headboard leg hole facing up (recessed hole should be facing
the floor) and the top holes facing inward. Use a rubber mal-
let or hammer and block of wood to align and insert doweled
ends of the assembled headboard into the leg. Repeat process
on other leg. Repeat same process for the assembled foot-
board. See figure 1.
Insert mattress support feet into each of the mattress
supports. See figure 2.
Figure 1
Figure 2
NOTE: Cracks or checks in
logs are a natural phenomenon
that occurs when moisture es-
capes as the logs dry and sea-
son. They do not affect the
structural integrity of the wood
and are not considered defects.
CALIFORNIA PROPOSITION 65 WARNING
This product may have an indoor finish applied that contains For-
maldehyde (50-00-0), a substance known to the State of California
to cause cancer.
For more information go to www.P65Warnings.ca.gov

STEP 3 Assemble undercarriage by laying the bedrails parallel
to each other, with holes facing inward. Using a rubber
mallet or hammer and block of wood, align and insert
mattress supports into the bed rails, as shown in figure
3.
Figure 3
Figure 7
Figure 5
Figure 4
STEP 6
STEP 4
STEP 5
STEP 7
Align and insert the doweled ends of the assembled under-
carriage into the lower holes of the headboard, (make sure
support feet are facing the floor and the recesses hole is to
the back). Repeat process on the footboard. See figure 4.
Secure legs to the undercarriage with 5/16” washer and 5” hex
washer head screw through the four recessed holes. Secure and
tighten all hex washer head screws. See figure 5.
1/4” x 5” Hex washer head screws and 5/16” washer
Using 2 1/2” screws, attach an angle brace to each leg
and bed rail as shown in figure 6.
Figure 6
Leg Side rail
Secure ALL doweled joints with 2 1/2” screws. Place
screws perpendicular through the dowels into the logs.
See figure 7 for placement.
Factory: 1 Lakeland Place, Edmore, Michigan 48829, Phone: [phone] Fax: [phone]
www.lakelandmills.com
Your bed is now assembled and is ready for immediate use
or for a finish of your choice. Sweet dreams!
Check tightness periodically.
2 1/2” Screws
Perpendicular
IMPORTANT!
If you have hardware left over
after completing your unit, it
most likely has been assembled
incorrectly, and may not be
safe to use. Please call Cus-
tomer Service at 800-427-5136
fir assistance,