LaMotte WaterLink SpinTouch 3580 User manual

FILLING: SINGLE-USE DISK
TESTING
QUICK
START GUIDE
BEFORE FIRST USE
¬Fully charge battery.
¬Ensure your Spin Touch has the latest firmware:
1. Download and install the WaterLink Connect Desktop application for Windows®at
www.waterlinkconnect.com/Downloads/Application.
2. Plug meter into the computer with the provided USB cable and launch WaterLink
Connect desktop application from the Start Menu.
3. Any firmware updates will automatically be applied to the meter.
1. Fill the disk using slow, even pressure. The sample
water will fill the spaces between the baffles in a
counterclockwise order. Each space will fill from the
bottom to the top. Sample water should be added until
the sample water in the fourth chamber fills to the top
of the chamber slightly past the embossed fill line. It is
OK to fill slightly past the fill line.
Correct Fill
(Fill line)
2. Do not overfill the disk. If the disk is overfilled, sample
water will flow out of the overflow hole in the center of
the disk. The disk is not leaking. Dry the disk and run
the test.
Over
Filled
(Dry disk before placing in meter)
3. Do not under fill the disk. If the disk is under filled, the
reagent chambers will not fill entirely and results will
be inaccurate.
Under
Filled
4. Wet disks should be dried thoroughly with a lint free
wipe. The disk should be handled by the edges.
5. Disks should be filled and used within 10 minutes. They cannot be filled ahead of time.
1. Press and hold until the meter turns
on.
2. Tap . Select a sanitizer type. Tap
to confirm.
3. Tap . Select a disk series (found on
disk packaging). Tap to confirm.
4. Remove disk from packaging.
5. Use syringe (1189) to fill disk with
pool or spa water sample.
6. Insert disk. Cover disk with Universal
Disk Cover. Close lid.
7. Tap to start test. Tap to stop the test.
8. Results will be displayed.
9. Select an option.
- Tap to return to the Test Screen.
- Tap highlighted to save test results
to test log if Auto Save is not enabled.
- Tap the hightlighted to send the results
to the enabled Mobile Bluetooth Printer.
- Tap highlighted to send results to
Bluetooth enabled device.
10. Press and hold for 2 seconds to turn
meter off.
NOTE: For water samples over 100 °F (38 °C) subtract 0.3 from pH result or, for the most accurate result, wait
until water sample is below 90 °F (32 °C) to test.

1. Fill any unused section of the disk using slow, even
pressure. Add the sample water until the Blank
Chamber is full and the Over Flow Chamber is partially
filled.
Correct Fill
Blank
Chamber
Over Flow
Chamber
2. Do not overfill the disk. If the disk is overfilled, sample
water will flow out of the vent hole in the center of the
disk. The disk is not leaking. Dry the disk and run the
test.
Over
Filled
(Dry disk before placing in meter)
Blank
Chamber
Over Flow
Chamber
3. Do not under fill the disk. If the disk is under filled, the
blank chamber will not be full. The reagent chambers
will not fill entirely and results will be inaccurate.
Under Filled
Blank
Chamber
4. Do not introduce air bubbles into the disk. The reagent
chambers will not fill entirely and results will be
inaccruate. Remove the water sample with the syringe
and refill.
Air Bubble
5. Wet disks should be dried thoroughly with a lint free wipe. Handle the disk by the edges.
Between tests store the disk on a flat surface. Do not agitate a partially filled disk to avoid
leaking and contamination. Partially used disks should be discarded at the end of the day.
FILLING: MULTIPLE-USE DISK
Compatible with iPhone 6 Plus,
iPhone 6, iPhone 5s, iPhone 5c,
iPhone 5, iPad Air 2, iPad Air, iPad
mini 3, iPad mini 2, iPad mini, and
iPad (4th generation).
Compatible with Android devices.
DOS & DON’TS
¬Hold syringe vertically when filling disks.
¬Do not fill disk while in the meter. Fill disk on clean, dry surface.
¬The disk should not contain any large air bubbles. Air bubbles will result in erroneous results.
¬Only the Universal Disk Cover (Code 1719) can be used with the WaterLink®Spin Touch™.
¬Empty syringe of previous sample before filling with next sample.
¬Remove filled disk from meter after testing.
BLUETOOTH CONNECTION
The WaterLink®Spin Touch™is capable of connecting to a Bluetooth enabled device, such as a
phone or tablet, and the Mobile Bluetooth Printer. The Spin Touch will only connect to and print
from the LaMotte Bluetooth Printer [Code 5-0066]. Other Bluetooth printers are not supported.
Whenever the button appears on the touch screen the Spin Touch is capable of connecting
to a Bluetooth enabled phone or tablet. The will become highlighted when connected and
be dim when not connected. Whenever the button appears on the touch screen the Spin
Touch is capable of connecting to the Mobile Bluetooth Printer. The will be highlighted when
connected and dim when not connected. The Spin Touch cannot connect to both a phone or
tablet and the printer at one time.
For filling and troubleshooting tips go to: www.waterlinkspintouch.com
See the WaterLink®Spin Touch™manual for additional information.
[email protected]
410-778-3100 | 800-344-3100
www.lamotte.com
Disk Patent No. 8,734,734
FCl Patent No. 8,987,000
TCl Patent No. 8,993,337
3580-QG 11.15.17