Lamphus Cruizer Series User manual

www.online-led-store.com
US Toll Free: 1-855-LED-ONLINE (533-6654)
International: 1-909-212-0993
Fax: [phone]
E-mail: [email protected]
LAMPHUS®Cruizer™Series
LED Flood/Spot Off-Road Light Bar
SKU: ORZLEDLBR104, 107, 112, 122, 136, 144
(CRLB06, CRLB12, CRLB24, CRLB42, CRLB78, CRLB96)
IMPORTANT: READ CAREFULLY BEFORE ASSEMBLY AND USE.
Proper installation of this product requires the installer to have a good understanding of
automotive electronics, systems, and procedures.
If mounting this product requires drilling holes, the installer MUST be sure that no vehicle
components or other vital parts could be damaged by the drilling process.Check both sides of
the mounting surface before drilling begins. Also de-burr any holes and remove any metal
shards or remnants. Install grommets into all wire passage holes.
If this manual states that this product may be mounted with suction cups, magnets, tape or
Velcro®, clean the mounting surface and dry thoroughly prior to apply adhesive for maximum
adhesion.
Do not attempt to activate or control this device in a hazardous driving situation.
Mounting Diagram # 1
•
•
•
•
Do not install this product or route any wires in the deployment area of your air bag. Equipment
mounted or located in the air bag deployment area will damage or reduce the effectiveness of
the air bag, or become a projectile that could cause serious personal injury or death. Refer to
your vehicle owner’s manual for the air bag deployment area. The User/Installer assumes full
responsibility to determine proper mounting location, based on providing ultimate safety to all
passengers inside the vehicle.
This product contains either strobe light(s), halogen light(s), high-intensity LEDs or a
combination of these lights. Do not stare directly into these lights.Momentary blindness and/or
eye damage could result.
•
•
Online LED Store © 2012-2018 All Rights Reserved
Mounting
Select a desired mounting location. Make sure there is at least 5” of clearance in order for
the light to fit properly over the mounting location.
Place the Swivel Bracket over the desired mounting surface.
Mark the area where the mounting hole(s) is to be drilled. Confirm that no vehicle parts
could be damaged by the drilling process.
Using a drill bit of appropriate size, drill a mounting hole for the Mounting Bolt. Thoroughly
de-burr all hole(s).
Secure the Swivel Bracket onto the mounting surface using the included fasteners.
Adjust the light unit to the desired tilt angle prior to tightening the fasteners all the way.
Refer to Mounting Diagram # 1 for additional details.
1.
2.
3.
4.
5.
6.
7.
CAUTION! Permanent mounting of this product will require drilling. It is
absolutely necessary to make sure that no other vehicle components could
be damaged by this process. Check both sides of the mounting surface
before starting. If damage is likely, select a different mounting location.
Swivel Bracket:
Mounting Surface

Online LED Store ©2012-2018 All Rights Reserved
Mounting Diagram # 2
Mounting Surface
Select a desired mounting location. Make sure there is at least 5” of clearance in order for
the light to fit properly over the mounting location.
Affix the L-shaped brackets to the light bar by using the included fasteners. Do not tighten
all the way.
Place the light bar with the L-shaped brackets over the desired mounting surface.
Mark the area where the mounting holes are to be drilled. Confirm that no vehicle parts
could be damaged by the drilling process.
Using a drill bit of appropriate size, drill a mounting hole for the Mounting Bolt. Thoroughly
de-burr all hole(s).
Secure the light unit onto the mounting surface using the included fasteners.
Adjust the light unit to the desired tilt angle prior to tightening the fasteners all the way.
Refer to Mounting Diagram # 2 for additional details.
1.
2.
3.
4.
5.
6.
7.
8.
L-shaped Brackets (12"+ models only)
RED – To 10-30 VDC Power Source
BLACK – To Chassis Ground
Input Voltage: 12 - 30 VDC
Model
CRLB06
CRLB12
CRLB24
CRLB42
CRLB78
CRLB96
Amperage @ 12 VDC
1
2
4
8
16
20
Output Wattage
18
36
72
126
234
288
Wiring
Specifications by Model
WARNING! All customer supplied wires that connect to the positive
terminal of the battery must be sized to supply at least 125% of the
maximum operating current and FUSED at the battery to carry that load. DO
NOT USE CIRCUIT BREAKERS WITH THIS PRODUCT!