Lancom 1780EW-3G User manual

Please observe the fol-
lowing when setting up
the device
1 For devices to be
operated on the desktop,
please attach the
adhesive rubber footpads
1 Do not rest any objects
on top of the device
1 Keep the ventilation slots
on the side of the device
clear of obstruction
1 In case of wall mounting,
Use the drilling template
as supplied
1 Rack installation with the
optional LANCOM Rack
Mount (not supplied)
 1780EW-3G

 
LANCOM, LANCOM Systems and LCOS are registered trademarks. All other names or descriptions used may be trademarks or registered trademarks of their owners. Subject to change without notice. No liability for technical errors and/or omissions. 110933/0711


Use a cable with
the green-colored
connectors to con-
nect the interfaces
ETH2 to your WAN
modem.


Screw the two supplied
WLAN antennas onto
the connectors WLAN1
and WLAN2. Depending
on how the antennas
are to be used, 'Antenna
Grouping' may need to
be congured in order to
provide the desired MIMO
behavior.


Slide the SIM card into the slot using the
marker to ensure that the card is the right
way round.
Ensure that the SIM card clicks into place
on insertion. To remove the card from the
device again, press the card lightly into
the device. Let go to release the SIM card
from the slot.


Use a cable with
the kiwi-colored
connectors to con-
nect the interfaces
ETH1 to your PC or
a LAN switch.



Screw the two supplied
cellular antennas onto the
connectors 3G Aux and
3G Main.
Alternatively screw
the free available GPS
antenna onto the connec-
tors 3G Aux (see included
voucher).

No Device switched off
Constant green Device operational
Blinking green Conguration password not set.
Without a conguration password,
the conguration data in the device is
unprotected.

No No networking device attached
Constant green Connection to network device
operational, no data trafc
Flickering green Data trafc
4
LANCOM1681V
Power
VDSL
Online ETH1 ETH2 VPN ETH3 ETH4
ISDNStatus

When connecting the
cable to the device, turn
the bayonet connector
90° clockwise until it
clicks into place.
Use only the supplied
power adapter.
5

No VPN connection inactive
Blinking gree n Establishing VPN connections
green constantly on VPN connection active

No UMTS interface switched off
Blinking red/green SIM card error
Blinking orange Logging on to cellular network
orange constantly on Logon to cellular network successful
green constantly on or
blinking
Cellular connection active; faster blinking
indicates faster connection

No No WLAN network dened or WLAN
module deactivated. The WLAN module is
not transmitting beacons.
Green At least one WLAN network is dened
and WLAN module activated. The WLAN
module is transmitting beacons.
green inverse
ashing
Number of ashes = number of connected
WLAN stations and P2P wireless connec-
tions, followed by a pause (default).
Alternatively the frequency of the ashing
can indicate signal strength over the
dened P2P link or the signal strength
between the access point and the device
operating in client mode.
Blinking green DFS scanning or other scan procedure.

Power supply 12 V DC, external power supply unit (230 V) with bayonet connector to prevent unplugging
Power consumption Max. ca.13.5 W
Environment Temperature range 5 – 40 °C; humidity 0 – 95%; non-condensing
Housing Robust synthetic housing, rear connectors, ready for wall mounting, Kensington lock; measures
210 x 45 x 140 mm (W x H x D)
Number of fans None; fanless design, no rotating parts, high MTBF

WAN 10/100Base-TX, autosensing, auto node hub
LAN 10/100/1000 Base-TX, autosensing, auto node hub
External antenna con-
nectors
Two reverse SMA connectors for external LANCOM AirLancer Extender antennas or for anten-
nas from other vendors. Please respect the restrictions which apply in your country when
setting up an antenna system. For information about calculating the correct antenna setup,
please refer to www.lancom.eu.
External antenna con-
nectors
Two SMA antenna connectors for external UMTS antennas (RX diversity) or for operating a GPS
antenna at the AUX connector
Serial interface Serial conguration interface / COM port (8-pin Mini-DIN):
9,600 - 115,000 baud, suitable for optional connection of analog/GPRS modems. Supports
internal COM-port server and provides transparent asynchronous serial-data transfer via TCP

Ethernet PPPoE, Multi-PPPoE, ML-PPP, PPTP (PAC or PNS) and plain Ethernet (with or without DHCP),
RIP-1, RIP-2, VLAN, IP

Supported standards: UMTS, HSPA+ (HSDPA with up to 21 Mbps, HSUPA with up to 5.76 Mbps), EDGE and GPRS
support
UMTS HSxPA bands 850/900/1900/2100 MHz
EDGE GPRS bands 850/900/1800/1900 MHz (EDGE to max. 236 Kbps)

CE EN 55022, EN 55024, EN 60950
2.4 GHz WLAN ETS 300 328
5 GHz WLAN EN 301 893 Version 1.5.1, EN 302 502 (BFWA)
Notications Certications notied in Germany, Belgium, Netherlands, Luxembourg, Austria, Spain, Switzer-
land, UK, Italy, Portugal, Czech Republic, Denmark, Malta, France

Manual Hardware Quick Reference (DE/EN)
Installation Guide (DE/EN/FR/ES/IT/PT/NL)
CD/DVD CD/DVD with rmware, management software (LANcong, LANmonitor, LANCAPI) and docu-
mentation
Cable 2 Ethernet cable, 3m (LAN: kiwi-colored connector; WAN: green connector)
Antennas Two 3dBi dipole dualband antennas
Antennas Two 2-dBi dipole UMTS/GPRS antennas (850-960 Mhz and 1700-2220 Mhz)
Power adapter External power supply adapter (230V), NEST 12 V/1.5 A DC/S, barrel connector 2.1/5.5 mm
bayonet, LANCOM item no. 110723
                          



Connect the device to a
PC with a conguration
cable
(available as accessory).
H>B
BD9:B
d f g
a
b
ba c d f g
c
e
e
When working with separately purchased antennas, please ensure you
do not exceed the maximum permissible transmission power. The system
operator is responsible for adhering to the threshold values.
Antennas are only to be attached or changed when the device is switched off.
Mounting or demounting antennas with the device switched on may cause the
destruction of the 3G or WLAN modules!
5
The SIM card is only to be
inserted or removed when the
device is switched off. Inserting
or removing the SIM card with the device
switched on may cause the destruction of
the 3G module!
5
A6C8DB&,-%:L"(<
(< KEC
:I='
EdlZg
:I=& LA6C
License information for the device rmware (LCOS) is available in the le LCOS-Licenses.txt on the data medium
supplied.