Lancom 1783VA-4G User manual

4
Hardware
Power supply 12 V DC, external power adapter (230 V); bayonet connector to secure against disconnection
Power consumption Max. ca. 14 W
Environment Temperature range 0–35 °C; humidity 0–95 %; non-condensing
Housing Robust plastic housing, rear connectors, ready for wall mounting, Kensington lock; measures 210 x 45 x 140
mm (W x H x D)
Number of fans One quiet fan
Interfaces LANCOM 1783VA-4G over ISDN LANCOM 1783VA-4G over POTS
WAN: VDSL2 aVDSL2 as per ITU G.993.2; proles 8a, 8b, 8c, 8d,
12a, 12b, 17a
aCompatible to VDSL2 from Deutsche Telekom
aADSL conformity according to: ADSL2+ over ISDN
as per ITU G.992.5 Annex B/J with DPBO, ADSL2
over ISDN as per ITU G.992.3 Annex B, ADSL over
ISDN as per ITU G.992.1 Annex B.
aSupports just one virtual connection at a time in
ATM (VPI-VCI pair)
aVDSL2 as per ITU G.993.2;
proles 8a, 8b, 8c, 8d, 12a, 12b, 17a
aADSL conformity according to: ADSL2+ over POTS
as per ITU G.992.5 Annex A / Annex M with DPBO,
ADSL2 over POTS as per ITU G.992.3 Annex A/L,
ADSL over POTS as per ITU G.992.1 Annex A.
aSupports just one virtual connection at a time in
ATM (VPI-VCI pair)
ETH 4 individual ports, 10 / 100 / 1000 Mbps Gigabit Ethernet, by default set to switch mode. Up to 3 ports can
be operated as additional WAN ports. Ethernet ports can be electrically disabled in the LCOS conguration.
ISDN 1 / ISDN 2 ISDN1: Internal (NT) or external (TE) ISDN bus. This feature is controlled by LCOS.
According to the settings, connect the light-blue ISDN cable either to the NTBA or the ISDN terminal device.
ISDN 2: Internal (NT) ISDN bus. Use the light-blue ISDN cable to connect the ISDN interface to the ISDN
device.
Analog 1 / Analog 2 Usethe cable of your analog devices to connect them with the analog interfaces. If necessary, use the
enclosed adapter.
Serial interface Serial conguration interface / COM-port (8-pin mini-DIN): 9,600 - 115,200 baud, suitable for optional
connection of analog / GPRS modems. Supports internal COM-port server and provides transparent
asynchronous serial-data transfer via TCP.
4G: Ant1, Ant2 TwoSMA connectors for the supplied dipole rod antennas (LTE, UMTS), compatible LANCOM AirLancer
antennas for 4G or 3G, or from other manufacturers. Please respect the restrictions that apply in your country
when setting up an antenna system (in particular the antenna gain and transmission power).
WAN protocols
VDSL, ADSL, Ethernet PPPoE, PPPoA, IPoA, Multi-PPPoE, ML-PPP, PPTP (PAC or PNS) and IPoE(with or without DHCP), RIP-1, RIP-2,
VLAN, GRE, L2TPv2 (LAC or LNS), IPv6 over PPP (IPv6 and IPv4/IPv6 dual stack session), IP(v6)oE
(autoconguration, DHCPv6 or static)
ISDN DSS1 (Euro-ISDN), PPP, X75, HDLC, ML-PPP, V.110/GSM/HSCSD
Data transmission in cellular networks
Supported standards: GPRS, EDGE, UMTS, HSxPA, HSPA+,LTE
LTE Band 1 (2100 MHz), band 3 (1800 MHz), band 7 (2600 MHz), band 8 (900 MHz),
band 20 (FDD800 MHz) with MIMO
UMTS/HSxPA/HSPA+ Band 1 (2100 MHz), band 8 (900 MHz) with diversity
EDGE/GPRS GSM 900 (900 MHz), DCS 1800 (1800 MHz), PCS 1900 (1900 MHz)
Max. transm. power +24dBm
Declaration of Conformity
Hereby, LANCOM Systems declaresthat this radio equipment is in compliance with Directive 2014/53/EU. The full text of the EU declarati-
on of conformity is available at the following internet address: www.lancom-systems.com/ce/
Package content
Documentation Quick Reference Guide (DE/EN), Installation Guide (DE/EN)
Cable 1 Ethernet cable, 3 m (kiwi-colored connectors);
for ISDN: 1 DSL cable for an IP-based line, 4.25m, 1 ISDN cable, 3 m (light-blue connectors);
for over POTS: 1 DSL cable, 3 m (dark-blue connectors)
Adapters 2 TAE adapters (RJ11 - TAE)
Antennas 2 LTE / 4G antennas for LTE/ UMTS
Power adapter External power supply adapter (230 V); NEST 12 V / 1.5 A DC/S; barrel connector 2.1 / 5.5 mm bayonet;
LANCOM item no. 111301 (EU, 230 V); LANCOM item no. 111302 (UK, 230 V)
LANCOM 1783VA-4G
DSL
ETH 2
Power
ETH 1
Online
ISDN 1
ETH 4 ETH 3 VPN
Analog 1 Analog 2 ISDN 2
Reset
VoIP 4G
a Power
Off Device switched off
Green, permanently* Device operational, resp. device paired / claimed
and LANCOM Management Cloud (LMC)
accessible
Green / red, blinking Conguration password not set. Without a
conguration password, the conguration data in
the device is unprotected.
Red, blinking Charge or time limit reached
1x green inverse
blinking*
Connection to the LMC active, pairing OK, device
not claimed
2x green inverse
blinking*
Pairing error, resp.
LMC activation code not available
3x green inverse
blinking*
LMC not accessible, resp.
communication error
b Online
Off WAN connection inactive
Green, permanently WAN connection active
Red, permanently WAN connection error
c DSL
Off Interface deactivated
Green, permanently DSL connection active
Green, ickering DSL data transfer
Red, ickering DSL transfer error
Red/orange, blinking DSL hardware error
Orange, blinking DSL training
Orange, permanently DSL sync
Green, blinking DSL connecting
d Analog
Off Interface deactivated
Green, permanently Interface activated
Orange, blinking Incoming call
Green, blinking Connection active
f ETH
Off No networking device attached
Green, permanently Connection to network device operational, no
data trafc
Green, ickering Data transmission
Please observe the
following when setting
up the device
aFor devices to be
operated on the
desktop, please attach
the adhesive rubber
footpads
aDo not rest any objects
on top of the device and
do not stack multiple
devices
aKeep the ventilation
slots on the side of
the device clear of
obstruction
aIn case of wall
mounting, use the
drilling template as
suppliedn
aRack installation with
the optional LANCOM
Rack Mount (not
supplied)
LANCOM1681V
Power
VDSL
Online ETH1
ETH2 VPN ETH3 ETH4
ISDNStatus
This product contains separate open-source software components which are
subject to their own licenses, in particular the General Public License (GPL). The
license information for the device rmware (LCOS) is available on the device‘s
WEBcong interface under “Extras > License information“. If the respective
license demands, the source les for the corresponding software components
will be made available on a download server upon request.
MOUNTING AND CONNECTING THE DEVICE
LANCOM, LANCOM Systems and LCOS areregistered trademarks. All other names or descriptions used may be trademarks or registered trademarks of their owners. Subject to change without notice. No liability for technical errors and/or omissions. 111653/0817
TECHNICAL DETAILS
a c eb gf
dhij
LANCOM 1783VA-4G
Quick Reference Guide
Cloud-ready
Gigabit Ethernet 10/100/1000
ISDN 1 ISDN 2
TE / NT NT
VDSL / ADSL
Analog1Analog2
eb g
g 4G
Off Cellular interface disabled
Green, permanently Connection to cellular network active
Green, ickering Cellular data transfer
Orange, permanently Logon to cellular network successful
Orange, blinking Logging on to cellular network
Red, permanently Hardware error/module unavailable
Red / green, blinking SIM card error (PIN)
Red / orange, blinking Uploading module rmware
h VoIP
Off No SIP accounts dened or VCM is off
Green, permanently All dened and active SIP accounts (outgoing)
registered successfully
Red, permanently Not all of the dened and active SIP accounts
were registered (possibly still in process)
Red or green,
inverse ashing
Number of currently used lines (connecting or
connected)
*) The additional power LED statuses are displayed in 5-seconds rotation if the
device is congured to be managed by the LANCOM Management Cloud.
i VPN
Off VPN connection inactive
Green, permanently VPN connection active
Green, ashing VPN connecting
j Reset
Reset button Operated e.g. with a paper clip
> Short press: Restart the device
> Long press: Reset the device
e ISDN
Off Interface deactivated
Green, permanently D-channel active
Green, blinking ISDN connected
Red, ickering ISDN transfer error
Red/orange, blinking ISDN hardware error
Red, permanently ISDN connection not enabled
Orange, blinking ISDN connecting
h
aLTE / 4G antennas
Connect the two supplied cellular
antennas to the connectors located
at the device‘s sides.
bVDSL / ADSL interface*
Use the supplied DSL cable for the
IP-based line to connect the VDSL
interface and the provider’s telephone
socket. For more information, please
contact your Internet service provider.
*For operation with over POTS devices
please use the DSL cable with the dark
blue plugs.
cEthernet interfaces
Use the cable with the kiwi-colored
connectors to connect one of the
interfaces ETH 1 to ETH 4 to your PC,
an IP telephone or a LAN switch.
dAnalog interfaces
Connect analog terminal devices to
the analog interfaces either directly
via RJ11 or with the help of the
enclosed TAE adapter.
eSerial interface
Conguring the device via the serial interface
requires a serial conguration cable
(available as an accessory).
fISDN interfaces
ISDN 1: Internal (NT) or external (TE) ISDN bus.
This feature is controlled by LCOS.
ISDN 2: Internal (NT) ISDN bus.
A 100-Ohm resistor for line termination is
switchable in LCOS.
gPower
When connecting the cable to the device, turn
the bayonet connector 90° clockwise until it
clicks into place.
Use only the supplied power adapter.
hSIM card slot (bottom side of the device)
Release the SIM-card holder and lever it
upwards. Slide the SIM card into the guide slot
of the SIM-card holder. Press the holder down
until it clicks into place. SIM
a a
cdf