Land Pride GS2572 User manual

Table of Contents
Cover photo may show optional equipment not supplied
with standard unit.
For an Operator’s Manual and Decal Kit in French
Language, please see your Land Pride dealer.
Read the Operator’s Manual entirely. When you see this symbol,
the subsequent instructions and warnings are serious - follow
without exception.Your life and the lives of others depend on it!
!
Grading Scrapers
GS2572, GS2584 & GS2596
303-268M
Operator’s Manual
Printed 9/25/18
26654
Pictured with optional Scarifier Shanks

9/25/18GS2572, GS2584 & GS2596 Grading Scrapers 303-268M
Machine Identification
Record your machine details in the log below. If you replace this manual, be sure to transfer this information to the new
manual.
If you, or the dealer, have added Options not originally ordered with the machine, or removed Options that were
originally ordered, the weights and measurements are no longer accurate for your machine. Update the record by
adding the machine weight and measurements provided in the Specifications & Capacities Section of this manual with
the Option(s) weight and measurements.
Dealer Contact Information
Model Number
Serial Number
Machine Height
Machine Length
Machine Width
Machine Weight
Delivery Date
First Operation
Accessories
Name:
Street:
City/State:
Telephone:
Email:
WARNING: Cancer and reproductive harm - www.P65Warnings.ca.gov
!
California Proposition 65

Table of Contents
© Copyright 2018 All rights Reserved
Land Pride provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the
preparation of this manual, Land Pride assumes no responsibility for errors or omissions.Neither is any liability assumed for damages resulting from the use
of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit.This publication describes the state of this
product at the time of its publication, and may not reflect the product in the future.
Land Pride is a registered trademark.
All other brands and product names are trademarks or registered trademarks of their respective holders.
Printed in the United States of America.
9/25/18 GS2572, GS2584 & GS2596 Grading Scrapers 303-268M
Table of Contents
Important Safety Information . . . . . . . . . . . . . 1
Safety at All Times . . . . . . . . . . . . . . . . . . . . . . . . . 1
Look for the Safety Alert Symbol . . . . . . . . . . . . . . . 1
Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Using This Manual . . . . . . . . . . . . . . . . . . . . . . . . . 5
Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Owner Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Further Assistance . . . . . . . . . . . . . . . . . . . . . . . . 6
Section 1: Assembly & Set-up . . . . . . . . . . . . 7
Tractor Requirements . . . . . . . . . . . . . . . . . . . . . . . 7
Torque Requirements . . . . . . . . . . . . . . . . . . . . . . . 7
Hitch Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Shank Assembly (Optional) . . . . . . . . . . . . . . . . . . . 7
3-Point Hook-up . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Section 2: Adjustments . . . . . . . . . . . . . . . . . . 9
Level Scraper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Blade Height Adjustment . . . . . . . . . . . . . . . . . . . . . 9
Initial Preparation . . . . . . . . . . . . . . . . . . . . . . . . . 9
Lower Cutter Blades . . . . . . . . . . . . . . . . . . . . . . 9
Raise Cutter Blades . . . . . . . . . . . . . . . . . . . . . . . 9
Adjust Cutter Blades to Grade a Crown . . . . . . . . 9
Shank Height Adjustment . . . . . . . . . . . . . . . . . . . 10
Section 3: Operating Instructions . . . . . . . . . 11
Operating Checklist . . . . . . . . . . . . . . . . . . . . . . . . 11
Tractor Shutdown Procedure . . . . . . . . . . . . . . . . 11
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . 11
Transporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
General Operating Instructions . . . . . . . . . . . . . . . 12
Section 4: Options . . . . . . . . . . . . . . . . . . . . . 13
Scarifier Shanks . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Rear Mounted Cutting Blades . . . . . . . . . . . . . . . . 13
Section 5: Maintenance . . . . . . . . . . . . . . . . . 14
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Cutting Blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Shank Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Skid Shoes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Long-Term Storage . . . . . . . . . . . . . . . . . . . . . . . . 15
Ordering Replacement Parts . . . . . . . . . . . . . . . . . 15
Section 6: Specifications & Capacities . . . . 16
Section 7: Features & Benefits . . . . . . . . . . . 17
Section 8: Torque Values Chart . . . . . . . . . . . 18
Section 9: Warranty . . . . . . . . . . . . . . . . . . . . 19

Table of Contents Continued
Parts Manual QR Locator
The QR (Quick Reference) code on the
cover and to the left will take you to the
Parts Manual for this equipment.
Download the appropriate App on your
smart phone, open the App, point your
phone on the QR code and take a picture.
Dealer QR Locator
The QR code on the left will
link you to available dealers
for Land Pride products.
Refer to Parts Manual QR
Locator on this page for
detailed instructions.
Table of Contents
9/25/18GS2572, GS2584 & GS2596 Grading Scrapers 303-268M
See previous page for Table of contents.

Important Safety Information
9/25/18 1
Important Safety Information
Listed below are common practices that may or may not be applicable to the products
described in this manual.

Tractor Shutdown & Storage
If engaged, disengage power
take-off.
Park on solid, level ground and
lower implement to ground or onto
support blocks.
Put tractor in park or set park
brake, turn off engine, and remove
switch key to prevent unauthorized
starting.
Relieve all hydraulic pressure to
auxiliary hydraulic lines.
Wait for all components to stop
before leaving operator’s seat.
Use steps, grab-handles and
anti-slip surfaces when stepping
on and off the tractor.
Detach and store implement in an
area where children normally do
not play. Secure implement using
blocks and supports.
OFF
REMOVE
Look for the Safety Alert Symbol
The SAFETY ALERT SYMBOL indicates there is a
potential hazard to personal safety involved and extra
safety precaution must be taken. When you see this
symbol, be alert and carefully read the message that
follows it. In addition to design and configuration of
equipment, hazard control, and accident prevention are
dependent upon the awareness, concern, prudence, and
proper training of personnel involved in the operation,
transport, maintenance, and storage of equipment.
Safety Precautions for
Children
Tragedy can occur if the operator
is not alert to the presence of
children. Children generally are
attracted to implements and their
work.
Never assume children will remain
where you last saw them.
Keep children out of the work area
and under the watchful eye of a
responsible adult.
Be alert and shut the implement
and tractor down if children enter
the work area.
Never carry children on the tractor
or implement. There is not a safe
place for them to ride. They may
fall off and be run over or interfere
with the control of the power
machine.
Never allow children to operate the
power machine, even under adult
supervision.
Never allow children to play on the
power machine or implement.
Use extra caution when backing
up. Before the tractor starts to
move, look down and behind to
make sure the area is clear.
Safety at All Times
Careful operation is your best
assurance against an accident.
All operators, no matter how much
experience they may have, should
carefully read this manual and
other related manuals, or have the
manuals read to them, before
operating the power machine and
this implement.
Thoroughly read and understand
the “Safety Label” section. Read
all instructions noted on them.
Do not operate the equipment
while under the influence of drugs
or alcohol as they impair the ability
to safely and properly operate the
equipment.
The operator should be familiar
with all functions of the tractor and
attached implement and be able to
handle emergencies quickly.
Make sure all guards and shields
appropriate for the operation are in
place and secured before
operating implement.
Keep all bystanders away from
equipment and work area.
Start tractor from the driver’s seat
with hydraulic controls in neutral.
Operate tractor and controls from
the driver’s seat only.
Never dismount from a moving
tractor or leave tractor unattended
with engine running.
Do not allow anyone to stand
between tractor and implement
while backing up to implement.
Keep hands, feet, and clothing
away from power-driven parts.
While transporting and operating
equipment, watch out for objects
overhead and along side such as
fences, trees, buildings, wires, etc.
Do not turn tractor so tight as to
cause hitched implement to ride
up on the tractor’s rear wheel.
Store implement in an area where
children normally do not play.
When needed, secure attachment
against falling with support blocks.
Be Aware of
Signal Words
A signal word designates a degree or
level of hazard seriousness. The
signal words are:
Indicates a hazardous situation that, if
not avoided, will result in death or
serious injury.
Indicates a hazardous situation that, if
not avoided, could result in death or
serious injury.
Indicates a hazardous situation that, if
not avoided, may result in minor or
moderate injury.
WARNING
CAUTION
!
!
!
DANGER
!

Important Safety Information
9/25/18
2
Listed below are common practices that may or may not be applicable to the products
described in this manual.
Practice Safe Maintenance
Understand procedure before doing
work. Refer to the Operator’s
Manual for additional information.
Work on a level surface in a clean
dry area that is well-lit.
Lower implement to the ground and
follow all shutdown procedures
before leaving the operator’s seat to
perform maintenance.
Do not work under any hydraulic
supported equipment. It can settle,
suddenly leak down, or be lowered
accidentally. If it is necessary to
work under the equipment, securely
support it with stands or suitable
blocking beforehand.
Use properly grounded electrical
outlets and tools.
Use correct tools and equipment for
the job that are in good condition.
Allow equipment to cool before
working on it.
Disconnect battery ground cable (-)
before servicing or adjusting
electrical systems or before welding
on implement.
Inspect all parts. Make certain
parts are in good condition &
installed properly.
Replace parts on this implement
with genuine Land Pride parts only.
Do not alter this implement in a way
which will adversely affect its
performance.
Do not grease or oil implement
while it is in operation.
Remove buildup of grease, oil, or
debris.
Always make sure any material and
waste products from the repair and
maintenance of the implement are
properly collected and disposed.
Remove all tools and unused parts
before operation.
Do not weld or torch on galvanized
metal as it will release toxic fumes.
Use A Safety Chain
A safety chain will help control
drawn machinery should it
separate from the tractor drawbar.
Use a chain with the strength
rating equal to or greater than the
gross weight of the towed
implement.
Attach the chain to the tractor
drawbar support or other specified
anchor location. Allow only
enough slack in the chain to
permit turning.
Always hitch the implement to the
machine towing it. Do not use the
safety chain tow the implement.
Transport Safely
Comply with federal, state, and
local laws.
Use towing vehicle and trailer of
adequate size and capacity. Secure
equipment towed on a trailer with
tie downs and chains.
Sudden braking can cause a towed
trailer to swerve and upset. Reduce
speed if towed trailer is not
equipped with brakes.
Avoid contact with any overhead
utility lines or electrically charged
conductors.
Always drive with load on end of
loader arms low to the ground.
Always drive straight up and down
steep inclines with heavy end of a
tractor with loader attachment on
the “uphill” side.
Engage park brake when stopped
on an incline.
Maximum transport speed for an
attached equipment is 20 mph. DO
NOT EXCEED. Never travel at a
speed which does not allow
adequate control of steering and
stopping. Some rough terrains
require a slower speed.
As a guideline, use the following
maximum speed weight ratios for
attached equipment:
20 mph when weight of attached
equipment is less than or equal
to the weight of machine towing
the equipment.
10 mph when weight of attached
equipment exceeds weight of
machine towing equipment but
not more than double the weight.
IMPORTANT: Do not tow a load
that is more than double the weight
of the vehicle towing the load.
Tire Safety
Tire changing can be dangerous
and must be performed by
trained personnel using the
correct tools and equipment.
Always maintain correct tire
pressure. Do not inflate tires
above recommended pressures
shown in the Operator’s Manual.
When inflating tires, use a clip-on
chuck and extension hose long
enough to allow you to stand to
one side and NOT in front of or
over the tire assembly. Use a
safety cage if available.
Securely support the implement
when changing a wheel.
When removing and installing
wheels, use wheel handling
equipment adequate for the
weight involved.
Make sure wheel bolts have been
tightened to the specified torque.

Important Safety Information
9/25/18 3
Listed below are common practices that may or may not be applicable to the products
described in this manual.
Avoid High
Pressure Fluids Hazard
Escaping fluid under pressure can
penetrate the skin causing serious
injury.
Before disconnecting hydraulic
lines or performing work on the
hydraulic system, be sure to
release all residual pressure.
Make sure all hydraulic fluid
connections are tight and all
hydraulic hoses and lines are in
good condition before applying
pressure to the system.
Use a piece of paper or
cardboard, NOT BODY PARTS, to
check for suspected leaks.
Wear protective gloves and safety
glasses or goggles when working
with hydraulic systems.
DO NOT DELAY. If an accident
occurs, see a doctor familiar with
this type of injury immediately. Any
fluid injected into the skin or eyes
must be treated within
a few hours or
gangrene may
result.
Wear Personal Protective
Equipment (PPE)
Wear protective clothing and
equipment appropriate for the job
such as safety shoes, safety
glasses, hard hat, and ear plugs.
Clothing should fit snug without
fringes and pull strings to avoid
entanglement with moving parts.
Prolonged exposure to loud noise
can cause hearing impairment or
hearing loss. Wear suitable
hearing protection such as
earmuffs or earplugs.
Operating equipment safely
requires the operator’s full
attention. Avoid wearing
headphones while operating
equipment.
Use Seat Belt and ROPS
Land Pride recommends the use
of a CAB or roll-over-protective-
structures (ROPS) and seat belt
in almost all power machines.
Combination of a CAB or ROPS
and seat belt will reduce the risk
of serious injury or death if the
power machine should be upset.
If ROPS is in the locked-up
position, fasten seat belt snugly
and securely to help protect
against serious injury or death
from falling and machine overturn.
Keep Riders Off
Machinery
Never carry riders on tractor or
implement.
Riders obstruct operator’s view
and interfere with the control of
the power machine.
Riders can be struck by objects or
thrown from the equipment.
Never use tractor or implement to
lift or transport riders.
Avoid Underground
Utilities
Dig Safe, Call 811 (USA).
Always contact your local utility
companies (electrical, telephone,
gas, water, sewer, and others)
before digging so that they may
mark the location of any
underground services in the area.
Be sure to ask how close you can
work to the marks they positioned.
Prepare for Emergencies
Be prepared if a fire starts.
Keep a first aid kit and fire
extinguisher handy.
Keep emergency numbers for
doctor, ambulance, hospital, and
fire department near phone.
911
Use Safety
Lights and Devices
Slow moving tractors, skid steers,
self-propelled machines, and towed
equipment can create a hazard
when driven on public roads. They
are difficult to see, especially at
night. Use the Slow Moving Vehicle
sign (SMV) when on public roads.
Flashing warning lights and turn
signals are recommended
whenever driving on public roads.

Important Safety Information
Table of Contents
9/25/18GS2572, GS2584 & GS2596 Grading Scrapers 303-268M
4
818-267C
Caution Avoid Injury
26654
26661
35802
Safety Labels
Your Grading Scraper comes equipped with all safety labels in
place. They were designed to help you safely operate your
equipment. Read and follow their directions.
1. Keep all safety labels clean and legible.
2. Refer to this section for proper label placement. Replace
all damaged or missing labels. Order new labels from your
nearest Land Pride dealer. To find your nearest dealer,
visit our dealer locator at www.landpride.com.
3. Some new equipment installed during repair requires
safety labels to be affixed to the replaced component as
specified by Land Pride. When ordering new components
make sure the correct safety labels are included in the
request.
4. Refer to this section for proper label placement. To install
new labels:
a. Clean surface area where label is to be placed.
b. Spray soapy water onto the cleaned area.
c. Peel backing from label and press label firmly onto the
surface.
d. Squeeze out air bubbles with edge of a credit card or
with a similar type of straight edge.
838-614C
2" x 9" Red Reflector (2 places)
838-615C
2" x 9" Amber Reflector (1 place on GS2596 Only)
Important Safety Information

Introduction
Table of Contents
9/25/18 GS2572, GS2584 & GS2596 Grading Scrapers 303-268M 5
Terminology
“Right” or “Left” as used in this manual is determined by
facing the direction the machine will operate while in use
unless otherwise stated.
Definitions
Owner Assistance
The dealer should complete the Online Warranty
Registration at the time of purchase. This information is
necessary to provide you with quality customer service.
The parts on your Grading Scraper have been specially
designed by Land Pride and should only be replaced with
genuine Land Pride parts. Contact a Land Pride dealer if
customer service or repair parts are required. Your Land
Pride dealer has trained personnel, repair parts, and
equipment needed to service this implement.
Serial Number
For quick reference and prompt service, record model
and serial number on the inside cover page and again on
the warranty page. Always provide model number and
serial number when ordering parts and in all
correspondences with your Land Pride dealer. For
location of your serial number plate, see Figure 1.
Serial Number Plate Location
Figure 1
IMPORTANT: A special point of information related
to the following topic. Land Pride’s intention is this
information must be read & noted before continuing.
NOTE: A special point of information that the
operator should be aware of before continuing.
26661
Introduction
Land Pride welcomes you to the growing family of new
product owners. This Grading Scraper has been
designed with care and built by skilled workers using
quality materials. Proper assembly, maintenance, and
safe operating practices will help you get years of
satisfactory use from this implement.
Application
The Land Pride GS25 Series Grading Scrapers come in
72", 84" and 96" working widths with a Category l & ll
3-point hitch for attaching to tractors in the 40-90 hp
working range. The hitch is also Quick Hitch compatible.
Grading Scrapers have uses and applications in
landscaping, farms, ranches, construction sites, hunting
camps, fishing camps, logging sites, mining operations,
large estates, small acreages, sod farms, and municipal
and county rural road maintenance facilities. These
Grading Scrapers are uniquely designed to be extra user
friendly and a low cost alternative for road grading
applications. Unlike a box scraper, they are not designed
to transfer large volumes of dirt from one location to
another and as a result do not require the additional
horsepower that a box scraper normally requires. Nor
does it require the tending of tractor 3-point lift controls to
maintain grade that a box scraper might require.
Simply setting a properly adjusted GS25 Series Grading
Scraper on the ground and driving forward enables the
operator to grade off high spots and fill in ruts and low
spots on unimproved roads and lanes with little or no
manipulation of the tractors 3-point hitch controls. Unlike
a rear blade, they require no adjustment of blade angling
or offset positions. The GS25 Series Grading Scraper
simply and quickly moves dirt or aggregate from high
spots to low spots. Should a large accumulation of
unwanted buildup of soil or aggregate occur between the
blades, initiating a slight raise on the tractors lift controls
will allow excess material to flow out uniformly and evenly
under the leveling scraper blades.
See “Specifications & Capacities” on page 16 and
“Features & Benefits” on page 17 for additional
information and performance enhancing options.
Using This Manual
•This Operator’s Manual is designed to help familiarize
you with safety, assembly, operation, adjustments,
troubleshooting, and maintenance. Read this manual
and follow the recommendations to help ensure safe
and efficient operation.
•The information contained within this manual was
current at the time of printing. Some parts may change
slightly to assure you of the best performance.
•To order a new Operator’s or Parts Manual, contact
your authorized dealer. Manuals can also be
downloaded, free-of-charge, from our website at
www.landpride.com

Introduction
Table of Contents
9/25/18GS2572, GS2584 & GS2596 Grading Scrapers 303-268M
6
Further Assistance
Your dealer wants you to be satisfied with your new
Grading Scraper. If for any reason you do not understand
any part of this manual or are not satisfied with the
service received, the following actions are suggested:
1. Discuss any problems you have with your implement
with your dealership service personnel so they can
address the problem.
2. If you are still not satisfied, seek out the owner or
general manager of the dealership, explain the
question/problem, and request assistance.
3. For further assistance write to:
Land Pride Service Department
1525 East North Street
P.O. Box 5060
Salina, Ks. 67402-5060
E-mail address
lpser[email protected]
Hitch and Shank Set-up
Figure 1-1
26655
Position hitch straps
with large holes “A”
towards the front.

Section 1: Assembly & Set-up
Table of Contents
9/25/18 GS2572, GS2584 & GS2596 Grading Scrapers 303-268M 7
Section 1: Assembly & Set-up Shank Assembly (Optional)
Refer to Figure 1-1 on page 6:
When possible, the shanks are shipped assembled to the
Grading Scraper. Some shanks may need installation.
DANGER
!
To prevent serious injury or death:
Make adjustments to the implement after it has been properly
attached to a tractor and secured with solid non-concrete
supports in the up position. Never work around or under
equipment supported by hydraulics. Hydraulics can drop
equipment instantly if controls are actuated or if hydraulic
lines burst even when power to hydraulics is shut off.
WARNING
!
To prevent serious injury or death:
•Always keep your body extremities out from under the
shanks while adjusting them. It is possible for the shanks to
fall causing injury to your feet and/or legs.
•Keep clear of the shank slots while adjusting shank height.
Shanks can pinch body parts in the slots during adjustments.
Before installing shanks (#15), attach Grading Scraper to
the tractor’s 3-point hitch or raise front of scraper up and
support it with blocks. See“3-Point Hook-up” on page 8.
1. Remove shanks (#15) from shipping crate and insert
them into the front slots with tips pointing forward.
2. Secure shanks with lock pins (#14) and
hairpin cotters (#11).
NOTE: See Section 2: Adjustments for shank depth.
Tractor Requirements
Tractor horsepower should be within the range noted
below. Tractors outside the horsepower range must not
be used.
Required Horsepower Rating . . . 40 to 90 horsepower
Hitch Type . . . . . . . . . . . . . 3 - Point Cat. I and Cat. II
WARNING
!
To avoid serious injury or death:
Lightweight tractors with rear attached implements may need
weights added to the front to maintain steering control.
Consult your tractor Operator’s Manual to determine proper
weight requirements and maximum weight limitations.
Torque Requirements
Refer to “Torque Values Chart” on page 18 to
determine correct torque values of fasteners during
assembly.
Hitch Assembly
Refer to Figure 1-1 on page 6:
1. Remove linchpins (#10) from hitch pins (#4).
2. Position hitch straps (#1 & #2) with large holes (A)
towards the front and mount large holes over end of
hitch pins (#4).
3. Attach middle and rear holes in hitch straps to clevis
plates with 3/4"-10 x 2" GR5 cap screws (#6), lock
washers (#9), and hex nuts (#8) as shown. Do not
tighten hardware at this time.
4. Reinsert linchpins (#10) and snap wire retainer over
hitch pins to secure hitch pins.
5. Attach channel brace (#3) to rear mounting lugs with
3/4"-10 x 5" GR5 cap screw (#7B), lock washer (#9),
and hex nut (#8). Do not tighten bolt at this time.
6. Attach channel brace (#3) and spacer (#5) to hitch
straps (#1 & #2) as shown with 3/4"-10 x 5" GR5 cap
screw (#7A), lock washer (#9), and hex nut (#8). Do
not tighten hardware at this time.
7. Draw all six hex nuts (#8) up snug. Make certain hitch
pins (#4) are loose in their holes. If hitch pin is tight,
readjust hitch frames (#1 & #2) until loose and then
tighten all six hex nuts (#8) to the correct torque.
8. Install 3/4" x 3 3/4" hitch pin (#12) to hitch straps and
secure in place with hairpin cotter (#13).

Section 1: Assembly & Set-up
Table of Contents
9/25/18GS2572, GS2584 & GS2596 Grading Scrapers 303-268M
8
Tractor 3-Point Hitch
Figure 1-2
26660
Cat. Il Lower
Hitch Point
Cat. l Lower Hitch Points
Cat. Il Lower
Hitch Point
3-Point Hook-up
Refer to Figure 1-2:
DANGER
!
To avoid serious injury or death:
A crushing hazard exists while hooking-up and unhooking
implement. Keep people and animals away while backing-up
to implement or pulling away from implement. Do not operate
hydraulic controls while a person or animal is directly behind
the power machine or near the implement.
WARNING
!
To avoid serious injury or death:
•Lightweight tractors with rear attached implements may
need weights added to the front to maintain steering control.
Consult your tractor Operator’s Manual to determine
proper weight requirements and maximum weight
limitations.
•Always shut tractor down using “Tractor Shutdown
Procedure” provided in this manual before allowing anyone
including the operator to hook-up and unhook implement.
A 3-point Category I or Category ll 3-point hitch is
required. The lower arms of the 3-point hitch must be
stabilized to prevent side-to-side movement. Most
tractors have sway blocks or adjustable chains for this
purpose.
NOTE: Land Pride’s Quick Hitch can be attached to
the tractor to provide quick and easy 3-point hook-
up and detachment. See your nearest Land Pride
dealer to purchase a Quick-Hitch.
1. Determine your tractor’s hitch category.
a. A Category I tractor will have 7/8" dia. holes in the
lower hitch links and 3/4" dia. hole in the top link.
b. A Category II tractor will have 1 1/8" dia. holes in
the lower hitch links and 1" dia hole in the top link.
2. Slowly back tractor up to the Grading Scraper while
using the tractor’s 3-point hydraulic control to align
lower hitch arm holes with lower hitch holes.
3. Engage tractor park brake, shut tractor engine off,
and remove key before dismounting from tractor.
4. If your tractor has a Category II hitch, then insert
1 1/8" outside diameter bushings (#7) into the lower
hitch arm holes before installing hitch pins (#1).
Insert hitch pins (#1) through clevis lug holes and
lower hitch arm holes as shown. Secure hitch pins
with linchpins (#2)
5. Connect top center link (#6) to upper pivot hitch using
clevis pin (#3) and hairpin cotter (#4). If your tractor
hitch is a Category II hitch, then a 1" bushing (not
supplied) will be required to make the center link
hook-up.
6. Ensure that the lower hitch arms are stabilized to
prevent excessive side movement.
7. Return to the tractor and slowly operate controls up
and down to check for clearance between scraper
frame, tractor tires, and tractor drawbar. Move or
remove drawbar if it interferes with the scraper.
8. See “Level Scraper” on page 9.
NOTE: See Figure 1-2 below for correction location
of Cat. l and Cat. ll lower hitching points.
NOTE: It may be necessary to start your tractor and
slowly raise the 3-point hitch about 1" to 2" to align
the center link with the center hitch pin hole.

Section 2: Adjustments
Table of Contents
9/25/18 GS2572, GS2584 & GS2596 Grading Scrapers 303-268M 9
Section 2: Adjustments
Level Scraper
WARNING
!
To avoid serious injury or death:
Always keep your body extremities out from under the
implement. Hydraulics can drop the implement if a line burst
or if lift controls are accidentally actuated.
The Grading Scraper should be leveled from left to right
and front to back.
1. Park tractor. See “Tractor Shutdown Procedure” on
page 11
2. Manually adjust one lower lift arm on the tractor up or
down to level the Grading Scraper from left to right.
3. Manually adjust length of top-center-link to level
scraper from front to rear.
Blade Height Adjustment
Refer to Figure 2-1:
WARNING
!
To avoid serious injury or death:
Always keep your body extremities out from under the blade
carrier when adjusting cutting blade height. The Blade carrier
will fall while loosening its bolts.
Blade carrier (#2) can be lowered or raised equally on
both sides of the scraper to grade a surface level.
Position cutting edges even with the bottom of skid shoes
for non-aggressive grading action or adjust cutting edges
downward to 1 1/2" cutting depth for highly aggressive
cutting action. The most commonly used cutting depth is
1/4" below skid shoes.
Blade carrier (#2) can be lowered on the right side more
than the left side to grade a crown in the middle of a
roadway.
Initial Preparation
Refer to Figure 2-1:
1. Park Grading Scraper on a level hard surface such as
a concrete pad. Place gear selector in park and/or
set brakes.
2. Lower scraper until it is resting on the hard surface,
shut engine off and remove switch key.
3. Loosen bolts (#3) on both ends of blade carrier (#2).
Do not remove bolts (#3) or their nuts.
4. Restart tractor and raise scraper several inches off
the hard surface using tractor 3-point control lever.
5. Shut tractor engine off and remove switch key.
6. Place one long shim (#5) equal in thickness to the
cutting depth under each skid shoe (#1). Do not use
shims if cutting depth is 0 inches.
NOTE: Cutting depth is vertical distance from
bottom of skid shoe to bottom of cutting blades.
Blade Height Adjustment (Left-Hand Side Shown)
Figure 2-1
Lower Cutter Blades
1. Complete “Initial Preparation” on this page.
2. Restart tractor and operate 3-point control lever to
slowly lower skid shoes (#1) onto shims (#5).
3. Shut tractor engine off and remove switch key.
4. Make sure skid shoes (#1) are resting on shims (#5)
and blades (#4) are resting on the hard surface at
both ends of the scraper.
5. Tighten 5/8"-11 GR8 bolts (#3) to the correct torque.
Raise Cutter Blades
1. Complete “Initial Preparation” on this page.
2. Restart tractor and operate 3-point control lever to
slowly lower scraper until skid shoes (#1) are resting
on shims (#5). These shims should be thinner than
current cutting depth.
3. Make sure skid shoes (#1) are resting on shims (#5)
and cutter blades (#4) are resting on the hard surface
at both ends of the scraper.
4. Tighten 5/8"-11 GR5 bolts (#3) to the correct torque.
Adjust Cutter Blades to Grade a Crown
1. Complete steps 1-5 under “Initial Preparation” on
this page.
2. Place under the left-hand skid shoe (#1) and cutter
blades (#4) a shim (#5) equal in thickness to the
cutting depth.
3. Place under the right-hand skid shoe (#1) (right-
hand not shown) a second shim (#5) equal to the
thickness of the previous shim. Make sure this shim
does not extend under the blade carrier frame (#2).
4. Restart tractor and operate 3-point control lever to
slowly lower unit onto shims (#5)
5. On the left side, check to make sure skid shoes (#1)
and cutter blades (#4) are resting on shim (#5).
6. On the right-hand side (not shown), check to make
sure skid shoe (#1) is resting on shim (#5) and cutter
blades (#4) are resting on the hard surface.
7. Tighten 5/8"-11 GR5 bolts (#3) to the correct torque.
8. Make all grading passes with middle-of-roadway on
the left-hand side of the scraper.
26658

Section 2: Adjustments
Table of Contents
9/25/18GS2572, GS2584 & GS2596 Grading Scrapers 303-268M
10
Shank Height Adjustment
WARNING
!
To avoid serious injury or death:
•To prevent injury, make adjustments to the shank height
after the implement has been properly hooked to a tractor.
•Always keep your body extremities out from under the
shanks while adjusting them. It is possible for the shanks to
fall causing injury to your feet and/or legs.
•Keep clear of the shank slots while adjusting shank height.
Shanks can pinch body parts in the slots during adjustments.
Refer to Figure 2-2:
Shank settings are based on the vertical distance
measured from bottom edge of skid shoes to bottom
edge of shank tips.
Top Hole
3 1/2" Below
Third Hole
1/2" Above
26656a
Models GS2572 & GS2596 Only
The two longer bent pins are
used when mounting shanks
between clevis plates.
See Note in
Instructions
26656c
Second Hole
1 1/2" Below
Fourth Hole
2 1/2" Above
26656b
26656d
Shank Settings
Figure 2-2
1. Hook Grading Scraper to a tractor with a
category I or ll 3-point hitch before adjusting shanks.
2. Adjust shank height by removing hairpin cotter (#1)
and shank lock pin (#2).
3. Adjust shank up or down to the desired depth and
then replace shank lock pins and hairpin cotter.
NOTE: (GS2572 & GS2596 Only) Refer to “Top
Hole” illustration below: Two of the bent pins (#2)
supplied with model GS2596 only are 1" longer than
the others. Use these two pins to mount shanks
between 3-point clevis plates.

Section 3: Operating Instructions
Table of Contents
9/25/18 GS2572, GS2584 & GS2596 Grading Scrapers 303-268M 11
Operating Checklist
Hazard control and accident prevention are dependent
upon the awareness, concern, prudence, and proper
training involved in the operation, transport, storage, and
maintenance of the Grading Scraper. Therefore, it is
absolutely essential that no one operates the Grading
Scraper unless they are age 16 or older and have read,
fully understood, and are totally familiar with the
Operator’s Manual. Make sure the operator has paid
particular attention to:
•Important Safety Information, pages 1
•Section 1: Assembly & Set-up, page 7
•Section 2: Adjustments, page 9
•Section 3: Operating Instructions, page 11
•Section 5: Maintenance, page 14
Perform the following inspections before using your
Grading Scrapers.
Tractor Shutdown Procedure
The following are basic tractor shutdown procedures.
Follow these procedures and any additional shutdown
procedures provided in your tractor Operator’s Manual
before leaving the operator’s seat.
1. Reduce engine speed and shut-off all power to the
attachment.
2. Park tractor and attachment on solid, level ground.
3. Lower attachment until it is flat on the ground or on
non-concrete support blocks.
4. Put tractor in park or set park brake, turn off engine,
and remove switch key to prevent unauthorized
starting.
5. Relieve all hydraulic pressure to auxiliary hydraulic
lines.
6. Wait for all components to come to a complete stop
before leaving the operator’s seat.
7. Use steps, grab-handles and anti-slip surfaces when
stepping on and off the tractor.
Operating Checklist
Check Page
Check 3-point hook-up procedure. Be sure all
pins have been installed and are secured.
Refer to “Section 1: Assembly & Set-up”.
7
All adjustments have been made and pins have
been installed and are secured.
Refer to “Section 2: Adjustments”.
9
The operator has read and understands how to
operate the Grading Scraper.
Refer to “Section 3: Operating Instructions”.
11
Check scraper initially and periodically for loose
bolts and pins. Refer to “Torque Values Chart”.18
Safety Information
DANGER
!
To avoid serious injury or death:
•Allow only persons to operate this implement who have
fully read and comprehended this manual, who have been
properly trained in the safe operation of this implement, and
who are age 16 or older. Serious injury or death can result
from the inability to read, understand, and follow
instructions provided in this manual.
•Make adjustments to the implement after it has been properly
attached to a tractor and secured with solid non-concrete
supports in the up position. Never work around or under
equipment supported by hydraulics. Hydraulics can drop
equipment instantly if controls are actuated or if hydraulic
lines burst even when power to hydraulics is shut off.
•Never make contact with underground utilities such as
electrical power lines, gas lines, phone lines, etc. They can
cause serious injury or death from electrocution, explosion,
or fire. If in doubt, call 811 (USA) before digging so that
they can mark the location of underground services in the
area. For contact information, see Dig Safe in the
“Important Safety Information” starting on page 1.
•Do not allow anyone near the tractor or implement while
operating. Stop operation if bystanders are too close. They
can be hit by flying projectiles, become entangled in the
equipment, or ran over.
•Always secure equipment with solid, non-concrete supports
before working under it. Never go under equipment
supported by concrete blocks or hydraulics. Concrete can
break, hydraulic lines can burst, and/or hydraulic controls
can be actuated even when power to hydraulics is off.
WARNING
!
To avoid serious injury or death:
•Never carry riders on the implement or tractor. Riders can
obstruct the operator’s view, interfere with control of the
equipment, be pinched by moving components, become
entangled in rotating components, be struck by objects, be
thrown or fall from the equipment, etc.
•Allow only persons to operate this implement who have
fully read and comprehended this manual, who have been
properly trained in the safe operation of this implement, and
who are age 16 or older. Serious injury or death can result
from the inability to read, understand, and follow
instructions provided in this manual.
•Always keep your body extremities out from under the
shanks and cutting blades while removing, installing, and
adjusting them. It is possible for the cutting blades and/or
shanks to fall causing injury to your body.
•Do not use implement to lift objects; to pull objects such as
fence posts, stumps, etc; or to push objects. The unit is not
designed or guarded for these uses.
•Do not use implement to tow other equipment unless it is
designed with a tow hitch. Doing so can result in loss of
control and damage the equipment.
Section 3: Operating Instructions

Section 3: Operating Instructions
Table of Contents
9/25/18GS2572, GS2584 & GS2596 Grading Scrapers 303-268M
12
•Do not use implement as a man lift, work platform or as a
wagon to carry objects. It is not properly designed or
guarded for this use.
•Perform scheduled maintenance. Check for loose
hardware, missing parts, broken parts, structural cracks,
and excessive wear. Make repairs before putting implement
back into service. Serious breakdowns can result in injury
or death.
•Do not alter implement or replace parts on the implement
with other brands. Other brands may not fit properly or
meet OEM (Original Equipment Manufacturer)
specifications. They can weaken the integrity and impair the
safety, function, performance, and life of the implement.
Replace parts only with genuine OEM parts.
•Make sure safety labels are in their proper location and are
in good condition before operating the attached implement.
Read and obey all instructions on the labels.
Transporting
WARNING
!
To avoid serious injury or death:
•When traveling on roadways, transport in such a way that
other vehicles may pass you safely. Use accessory lights,
clean reflectors, and a slow moving vehicle sign that is
visible from the back to warn operators in other vehicles of
your presence. Always comply with all federal, state, and
local laws.
•Make sure implement does not block tractor’s Slow Moving
Vehicle (SMV) sign when transporting on a public road. If
operators in vehicles approaching from the back cannot
easily see the sign, then install one on the implement that is
visible to warn of your presence.
•Select a safe ground speed when transporting. Never travel at
a speed which does not allow adequate control of steering and
stopping, and never exceed 20 mph (32.2 km/h) with attached
equipment. Rough terrain requires a slower speed.
•Reduce ground speed when turning and leave enough
clearance to avoid making contact with obstacles such as
buildings, trees, fences, etc. Making contact can result in
equipment damage and cause serious injury or death.
1. Select a safe ground speed when transporting from
one area to another. Maximum transport speed for
the Grading Scraper is 20 mph. DO NOT EXCEED.
1. Be sure to reduce tractor ground speed when
turning; and leave enough clearance so the Grading
Scraper does not contact obstacles such as
buildings, trees, or fences.
2. Select a safe ground travel speed when transporting
from one area to another.
3. When traveling on roadways, transport in such a way
that faster moving vehicles may pass you safely.
4. When traveling over rough or hilly terrain, shift tractor
to a lower gear.
General Operating Instructions
By now you should have read the operator’s manual and
properly attached your GS25 Series Grading Scraper to
your tractor’s 3-point hitch. Whether you have chosen our
GS2572, GS2584 or GS2596, the working or grading
principals are the same.Your two grading blades should
be properly adjusted within the frame to achieve the
desired effect. This may take a little experimentation to
get your adjustments set just right depending on local
surface conditions in the area to be graded. Simply lower
your Grading Scraper until the left and right end skid
shoes are firmly in contact with the ground, then begin
driving forward.
Your two scraper blades should immediately begin
grading or shaving off high spots on the surface and
allowing dirt or aggregate material to flow under the
blades to fill in low spots. The lower the blades are set,
the more aggressive the cutting and grading action will
be. Depending on blade settings and surface conditions,
a build up may occur between the blades. This is no
cause for concern as simply raising the scraper slightly
with the 3-point hitch control lever will allow excess
material to flow out under the blades in an even and level
fashion. If an unwanted accumulation continues to occur
between the blades you may want to first adjust the rear
blade upward a bit our raise both blades if the unwanted
condition persists.
If surface conditions are such that the blades are
unsuccessful in shaving off high spots on a hard-packed
surface, begin lowering the optional scarifiers into
working position to a depth that enables you to achieve
the desired effect. The Land Pride 25 Series Grading
Scrapers are very user friendly attachments and with a
little practice you should begin achieving excellent
results.
See “Specifications & Capacities” on page 16 and
“Features & Benefits” on page 17 for additional
information and performance enhancing options.

Section 4: Options
Table of Contents
9/25/18 GS2572, GS2584 & GS2596 Grading Scrapers 303-268M 13
Scarifier Shanks
Refer to Figure 4-1:
Land pride offers an option for adding scarifier shanks to
your Grading Scraper for breaking up soil ahead of the
grader blades. The shanks can be adjusted from 2 1/2"
above the skid shoes to 3 1/2" below the skid shoes in 2"
increments.
GS2584 - 7 Shank Option Shown
Figure 4-1
Part Number & Description
303-462A PACKAGE, GS2572 6 SHANK OPTION
303-261A PACKAGE, GS2584 7 SHANK OPTION
303-260A PACKAGE, GS2596 8 SHANK OPTION
26668
Section 4: Options Rear Mounted Cutting Blades
Refer to Figure 4-2:
An additional set of cutter blades (#1) with mounting
hardware (#2 & #3) can be purchased through parts and
attached to the back side of blade carriers on Grading
Scrapers with serial number 825918 and higher. This will
allow the grading scraper to be used while traveling
forward and when backing-up.
Rear Mounting Cutting Blades
Figure 4-2
Part Number & Description
303-364A 72" GRADER BLADE KIT
303-365A 84" GRADER BLADE KIT
303-366A 96" GRADER BLADE KIT
35801
13
2
NOTE: Grader Blade Kit includes 1 Grader Blade
and required mounting hardware for the blades.

Section 5: Maintenance
Table of Contents
9/25/18GS2572, GS2584 & GS2596 Grading Scrapers 303-268M
14
Maintenance
Proper servicing and adjustment are key to the long life of
any implement. With careful inspection and routine
maintenance, you can avoid costly downtime and repair.
Check all bolts after using the unit for several hours to be
sure they are tight. Replace any worn, damaged, or
illegible safety labels by obtaining new labels from your
Land Pride dealer.
DANGER
!
To avoid serious injury or death:
Make adjustments to the implement after it has been properly
attached to a tractor and secured with solid non-concrete
supports in the up position. Never work around or under
equipment supported by hydraulics. Hydraulics can drop
equipment instantly if controls are actuated or if hydraulic
lines burst even when power to hydraulics is shut off.
WARNING
!
To avoid serious injury or death:
•Allow only persons to perform maintenance on this
implement who have been properly trained in its safe
operation.
•Perform scheduled maintenance. Check for loose
hardware, missing parts, broken parts, structural cracks,
and excessive wear. Make repairs before putting implement
back into service. Serious breakdowns can result in injury
or death.
•Do not alter implement or replace parts on the implement
with other brands. Other brands may not fit properly or
meet OEM (Original Equipment Manufacturer)
specifications. They can weaken the integrity and impair the
safety, function, performance, and life of the implement.
Replace parts only with genuine OEM parts.
•Always keep your body extremities out from under the
shanks and cutting blades while removing, installing, and
adjusting them. It is possible for the cutting blades and/or
shanks to fall causing injury to your body.
Section 5: Maintenance
Cutting Blade and Shank Tip Removal
Figure 5-1
Cutting Blades
Refer to Figure 5-1:
The front mounted and optional rear mounted cutting
blades (#3) have two cutting edges. Unbolt blades and
turn them over when bottom edges wear out. Inspect
5/8"-11 GR5 plow bolts (#4) and nuts (#5) for wear and
replace as needed. Reattach blades and tighten to the
correct torque. Replace cutting blades when both edges
are worn out.
Shank Tips
Refer to Figure 5-1:
Shank tips (#6) are removable by heating them in the
dimpled area on both sides and knocking them off with a
blunt punch. New shank tips need to be dimpled with a
punch after they are installed.
Dimpled Area 26659

Section 5: Maintenance
Table of Contents
9/25/18 GS2572, GS2584 & GS2596 Grading Scrapers 303-268M 15
Skid Shoe Maintenance
Figure 5-2
Skid Shoes
Skid shoes should be inspected at the beginning of each
season and replaced when material thickness is less
than 1/8" at any point. The skid shoe may be turned
around to extend its wear life if one end is wearing faster
than the other.
Order only genuine Land Pride parts from your local Land
Pride dealer when replacing skid shoe components.
Replace or turn skid shoe around as follows:
Refer to Figure 5-2:
1. Raise Grading Scraper 3" or more off the ground and
place support blocks under the scraper. Make sure
support blocks are positioned so they will not
interfere with skid shoe replacement.
2. Lower scraper onto support blocks, place tractor in
park, set park brakes, shut tractor engine off and
remove switch key.
3. Remove 3/8" hex flange locknuts (#3), 3/8"-16 plow
bolts (#1), and skid shoe (#2) from scraper.
4. Plow bolts should be checked for wear and replaced
if necessary.
5. Turn old skid shoe around or install new skid shoe to
scraper with 3/8"-16 x 1" GR5 plow bolts (#1) and
3/8" hex flange locknuts (#3).Tighten locknuts (#4) to
the correct torque.
6. Raise scraper up and remove support blocks.
26657
Long-Term Storage
Clean, inspect, service, and make necessary repairs to
the implement when storing it for long periods and at the
end of the season. This will help ensure the unit is ready
for field use the next time you hook-up to it.
1. Clean off any dirt and grease that may have
accumulated on the scraper. Scrape off compacted
dirt from the bottom of frame and then wash surface
thoroughly with a garden hose. A coating of oil may
also be applied to the lower frame area to minimize
oxidation.
2. Inspect Grading Scraper for loose, damaged, or
worn parts and adjust or replace as needed.
Repaint parts where paint is worn or scratched to prevent
rust. Ask your Land Pride dealer for aerosol touch-up
paint. They are also available in touch-up bottles with
brush, quarts, and gallon sizes by adding TU, QT, or GL
to the end of the aerosol part number.
3. Replace all damaged or missing decals.
4. Store scraper on a level surface in a clean, dry place.
Inside storage will reduce maintenance and make for
a longer scraper life.
Ordering Replacement Parts
Land Pride offers equipment in factory standard Beige
with black highlights. This implement is also available in
Orange.
When ordering an optional color, the suffix number
corresponding to the color must be added at the end of
the part number. Parts ordered without the suffix number
will be supplied in factory standard colors.
For example, if you are ordering a replacement part with
part number 555-555C and the existing part is orange,
then add the suffix 82 to the end of the number to make
the part number read 555-555C82.
Land Pride Touch-up Paint
Part No. Part Description
821-011C PAINT LP BEIGE SPRAY CAN
821-066C PAINT ORANGE SPRAY CAN
821-070C PAINT GP GLOSS BLACK SPRAY CAN
82 . . . . . . . Orange 85. . . . . . . Black

Section 6: Specifications & Capacities
Table of Contents
9/25/18GS2572, GS2584 & GS2596 Grading Scrapers 303-268M
16
GS25 Series
Specifications & Capacities
Model Numbers GS2572 GS2584 GS2596
Working Width 72" (1.83 m) 84" (2.13 m) 96" (2.44 m)
Overall Width 78 1/4" (1.99 m) 90 1/4" (2.29 m) 102 1/4" (2.60 m)
Number of Scarifier Shanks 678
Tractor horsepower Requirement 40-90 hp
(29.8-67.1 kw)
40-90 hp
(29.8-67.1 kw)
40-90 hp
(29.8-67.1 kw)
Unit Weight with Shanks 774 lbs (351.1 kg) 846 lbs (383.7 kg) 917 lbs (415.9 kg)
Overall Length 56 1/2" (1.44 m)
Overall Height 34 9/16" (87.8 cm)
Side Panel Height 14 5/8" (37.1 cm)
Side Panel Length 50" (1.27 m)
Side Panel Thickness Tractor 1/4" (6 mm) Thick with 2 3/4" (7.0 cm) formed edges.
Front Main Beam & Scarifier Support. 4"x 4" x 5/16" (10.2 cm x 10.2 cm x 0.8 cm) Reinforced heavy wall
tubing.
Rear Beam Construction 3"x 3"x 3/16" (7.6 cm x 7.6 cm x 0.5 cm) Heavy wall tubing.
Skid Shoe Dimensions 3/8" (10 mm) Thick x 2 3/4" (7.0 cm) wide x 50 1/4" (1.28 m) long.
Skid Shoe Material Constructed of high carbon steel
Scarifier Shank Construction - Optional Heat treated 4-position shank with dimpled-on hardened tips.
Cutting Edges Two 1/2" x 6" (1.3 cm x 15.2 cm) high carbon heat treated blades
that are reversible and replaceable.
Cutting Edge Placement Two parallel grading blades positioned at a 5 degree grading angle
with 20" (50.8 cm) fore and aft spacing in between leading edges.
Cutting Edge Adjustment Infinite vertical adjustment from level grade to 1 1/2" (3.8 cm) below
grade.
Shank Adjustments 3 1/2" and 1 1/2" (8.9 cm and 3.8 cm) below grade level.
1/2" and 2 1/2" (1.3 cm and 6.4 cm) above grade level.
Lower Draft Link Attachment Clevis type
Hitch Type Category l & ll 3-point hitch
Category l & ll Quick Hitch Compatible
Color Selections Land Pride Beige or Orange
Section 6: Specifications & Capacities
26667
34 9/16" (87.8 cm)
GS2572 = 78 1/4" (1.99 m)
GS2584 = 90 1/4" (2.29 m)
GS2596 = 102 1/4" (2.60 m)
56 1/2" (1.44 m)