Langham WC431222 User manual

Langham
Mirror Cabinet
Please follow the xing and care instrucions to ensure your cabinet is tted safely and retains
its high quality nish. Please retain this leaet for future reference.
Tools required (Not supplied)
Drill; 6.5mm masonry drill bit (6.5mm ceramic drill bit optional); Cross head screwdriver; Pencil;
Spirit level.
KEEP DIY TOOLS OUT OF THE REACH OF CHILDREN
Home safety advice
It is recommended that two people t the cabinet to ensure that it is tted safely.
Always take care when using an eletric drill, particularly in the bathroom. Always check for
hidden cables and pipe work before drilling and take extreme care if there is any water in the
working area.
It is advisable to use a residual current circuit breaker (RCCB).
Always wear suitable eye protection when drilling.
If the product is to be tted onto a ceramic tiled wall, a ceramic drill bit should be used. Always
ensure that the drill hole passes through the central tiled area rather than through the
grouted area. To prevent unnecessary damage to the tile, mask the area around the hole with
tape before drilling.
Do not strike the product with hard or sharp objects. Do not place hot objects against the glass
surfaces.
Do not overload the cabinet. Maximum safe working load is 10kg evenly distributed if mounted
on to a solid wall. If mounted on to a cavity wall reduce the load to 5kg evenly distributed.
Note: The wall plugs supplied are for use on solid walls only. For cavity walls or plasterboard use
specialist fixings that are available from all good DIY shops.
WC431222

Assembly Instructions - Tips
1. Please check that all parts are present before you start the assembly of your cabinet.
2. For ease and speed of assembly, we recommend that before you commence each step of the
assembly you identify all parts required.
3. We recommend that where possible all items are assembled near to the area in which they will be
placed in use.
4. For the protection of your cabinet during assembly (particularly painted nishes) we recommend
that the cabinet is placed on a protected surface to prevent damage.
5. During assembly please take care not to over-tighten any ttings as this may damage the product.
6. Do not use power screwdrivers.
Parts list
1. Top Panel
2. Bottom Panel
3. Left Side Panel
4. Right Side Panel
5. Backing Panel
6. Fixed Shelf
7. Adjustable Shelf
8. Door
Hardware list 8
2
6
3
5
7
4
1
A. Swivel
Plate
x 2
B. Catch
Plate
x1
C.Door
Knob
x1
D. Door
Catch
x1
E. Shelf
Support
x4
F. Mounting
Plate
x4
G. Washer
x 4
I. Screw
M5 x 50mm
x 8
J. Cap
10 x 3mm
x 8
K. Screw
M3 x 7mm
x 4
L. Wall Plug
7x7x35mm
x 4
M. Dowel
7.8 x 30mm
x 4
N. Screw
M4 x 16mm
x 1
O. Screw
M3 x 16mm
x 2
P. Screw
M3 x 8mm
x1
H. Screw
M4 x 51mm
x 4
Q. Glue

Step 2.
8
6
O(x2)
P(x1)
C(x1)
N(x1)
D(x1)
B(x1)
K(x4)
A(x2)
M(x4)
Ensure the swivel plates
are positioned as shown.
1

Step 3.
Step 4.
2
3
4
6
I(x4)
J(x4)
Note:
Apply Glue to Dowel.
Note:
Apply Glue to Dowel.

Step 5.
Step 6.
5
8
1
8
6
I(x4)
J(x4) M(x2)
Note:
Apply Glue to Dowel.

Step 7.
Step 8.
7
E(x4)

Step 9.
Step 10.
Fixing Instructions
1. Hold the cabinet against the wall in its
desired location. Check that the cabinet is
straight and level using a spirit level. Open the
door and mark the wall through the holes in
the back of the cabinet with a pencil.
2. Using a 6.5mm masonry drill, drill the holes
in the marked positions to a depth of 35mm
and insert the wall plugs into the holes in the
wall.
3. Insert the wall plugs to the surface of the
wall. If tting to a tiled surface, the wall plugs
should be inserted below the surface of the
tile to avoid cracking.
4. Hold the cabinet against the wall and align
the holes in the back of the cabinet with the
wall plugs. Insert the mounting screws and
washers through the holes in the back of
the cabinet and screw into the wall plugs to
complete the installation.
Please remove protective lm from
the double sided sticky tape before
tting the mounting plate. Ensure
the holes are aligned and t the
mounting plates into the corners of
the cabinet.
F(x4)
H(x4) L(x4)G(x4)

CAB 102 R02
Product Care Advice
To retain the best quality nish, clean the product regularly with a soft damp cloth.
Do not use abrasive or chemical cleaners, as these will damage the product.
For details of the other items in the Croydex range please visit our website: www.croydex.com
Croydex Ltd, Central Way, Andover, Hants, SP10 5AW, UK
Tel: [phone]
Fax: [phone]
Email: [email protected]
Made in China