Langley Street Patterson Dining Set LGLY5352 User manual

Label Picture Description QTY
ATable Top（pre-attched
screw base) 1
B Table Leg 4
C Table Leg Supporter 1
DTable Top Supporter 1
Assembly Instructions
Caution : You must read this before you proceed
DINING TABLE
Part List
Page 1 of 5

Label Picture Description QTY
①HEX NUT 5/16" 8
②SPRING WASHER 5/16" 8
③FLAT WASHER 5/16" 8
④SPANNER 12.8 1
⑤
JCBB M8 x 50mm
+ S/W 5/16"
+ F/W 5/16" x 22mm
4
⑥ALLEN KEY M4 1
Before
Beginning
Assembly:
Hardware
Assembly Preparation
Page 2 of 5

Step 1
Assembly Steps
Overview
This Table has multiple parts and may require up to some 30 minutes to
assemble. To give you an overview of the Table parts, the above picture is
to help you put the various parts into perspective. Please read through the
instructions below to familiarise yourself with the parts and steps before
assembly.
(1.1) Before assembly, please take out the Table Top supporter (D) from table leg supporter(C)
as arrow shown.
(1.2) Place the Table Leg (B) into the table supporter corner block.
Fix the hanger bolt with Hex Nut ①, Spring Washer ② and Flat Washer ③ using Spanner ④.
Repeat the step for another 3 leg.
Two adults are required whenever lifting and moving it.
DO NOT FULLY TIGHTHEN SCREWS.
FRONT FACING
Table Leg
(B)
Table Top
(A)
Table
Supporter
(C)
Table Top
Supporter
(D)
1.1
1.2
Page 3 of 5

Step 2
Step 3
With assistance from your adult partner, stand the Table up.
Inspect and make sure all parts are connected, locked and fully secured into
position.
Place the Top Table Supporter (D) onto the Double Roller Catch as
shown.
Your Table is now ready for use.
Assembly Steps
Place the Table top (A) on a soft surface to avoid any scratches or damages
to the product and place the Table Leg with the table supporter onto the of
table top support with your adult partner.
Fix the Table Top (A) with JCBB Bolt ⑤ + Spring Washer + Flat Washer
using Allen Key ⑥.
Repeat the step for another 3 leg.
FULLY TIGHTHEN THE BOLT.
Page 4 of 5

Care & Maintenance
Page 5 of 5

Label Picture Description QTY
A Chair Back 1
B Front Leg 1
C Side Stretcher (R) 1
D Side Stretcher (L) 1
E Side Rail (R) 1
F Side Rail (L) 1
G Cusion Seat 1
Assembly Instructions
Caution : You must read this before you proceed
DINING CHAIR
Part List
Page 1 of 7

Label Picture Description QTY
①
JCBC M6 x 50mm + S/W
M6 + F/W M6 x 13mm
4
②Allen Key M4 1
③FH Screw #8 x 32mm 4
④L Bracket 4
⑤CSK Screw M3.5 x 12mm 8
Before
Beginning
Assembly:
Hardware
Assembly Preparation
Page 2 of 7

Step 1
Assembly Steps
Overview
(1.1) Place the Side Stretcher (C) and Side Stretcher (D) on the Back Frame
(A) as shown. Side Stretcher (C) has a small hole for identification.
(1.2) Then, fix the Side Stretcher (C) and (D) with JCBC Bolt ①+ Spring
Washer + Flat Washer using Allen Key ②.
DO NOT FULLY TIGHTEN THE BOLT AND SCREWS.
This Dining Chair has multiple parts and may require up to some 30 minutes
to assemble. To give you an overview of the Dining Chair parts, the above
picture is to help you put the various parts into perspective. Please read
through the instructions below to familiarise yourself with the parts and
steps before assembly.
Front Leg (B)
Side Stretcher (C)
Cushion Seat (G)
Chair Back (A)
Side Rail (E)
Side Rail (F)
(C) has a small
hole for
identification.
(1.1)
(1.2)
(2.2)
Page 3 of 7

Step 2
Step 3
Place the Front Leg (B) on the Side Stretcher and Side Rail as shown.
Then,(3.1) fix the Front Leg (B) on the Side Stretcher with JCBC Bolt ①+
Spring Washer + Flat Washer using Allen Key ②.
Then,(3.2) fix the Front Leg (B) on the Side Rail with Screw ③using
Screwdriver (not provided).
DO NOT FULLY TIGHTEN SCREWS.
(2.1)Place the Side Rail (E) and Side Rail (F) on the Back Frame to. Side
Rail (E) has a small hole for identification.
(2.2) Then fix the Side Rail (E) and (F) with Screw ③using Screwdriver (not
provided).
DO NOT FULLY TIGHTEN THE BOLT AND SCREWS.
(E) has a small hole for
identification.
(3.1)
(3.2)
(2.1)
(2.2)
Page 4 of 7

Step 4
Step 5
Place the Cushion Seat (G) on the table and put the chair on it as shown.
Then, fix the Cushion Seat (G) with L-Bracket ④and Screw ③using
Screwdriver (not provided).
DO NOT FULLY TIGHTEN THE BOLT AND SCREWS.
①
If wobble
③
Test again
②
30
-
50mm
Page 5 of 7

Step 6
Place the dining chair on a Level Surface to check if it wobbles. loosen the
bolts and lift the dining chair some 30cm to 50cm high from the ground,
keep your feet and toes well away from the drop zone, and drop the dining
chair freely and vertically with the four legs, hitting the ground at the same
time.
This Drop Test will help to ensure that all the bolts and gaps to all reach full
alignment.
Test again for evenness on Level Surface.
If no wobbles are found, proceed to tighten all the Bolts.
Caution: When tightening the Bolts, tighten sequentially.
Do not tighten any screw fully and then towards the next one,this would
cause the frame to warp. If it still wobbles, loosen the bolts and execute this
same drop test.
If the dining chair is not Stable it could lead to damage to the product.
Inspect and make sure all parts are connected.
The dining chair is ready for use.
Caution: This dining chair can only be used on a flat, level surface.
Page 6 of 7

Care & Maintenance
Page 7 of 7