Lantech IES-2208CA User manual

Lantech
IES-2208CA
8 10/100TX + 2 10/100/1000T/Dual Speed SFP Combo
Managed Industrial Switch
User Manual
V2.01
Jan. 2013

Table of Content
Chapter 1 Introduction.............................................1
1.1 Hardware Features ........................................ 1
1.2 Software Features.......................................... 4
1.3 Package Contents.......................................... 7
Chapter 2 Hardware Description ............................8
2.1 Physical Dimension........................................ 8
2.2 Front Panel..................................................... 8
2.3 Bottom View................................................... 9
2.4 LED Indicators.............................................. 10
Chapter 3 Hardware Installation...........................12
3.1 Installation Steps.......................................... 12
3.2 DIN-Rail Mounting........................................ 13
3.3 Wall Mount Plate Mounting.......................... 15
3.4 Wiring the Power Inputs............................... 16
3.5 Wiring the Fault Alarm Contact.................... 17
3.6 Cabling......................................................... 18
Chapter 4 Network Application.............................22
4.1 Pro-Ring2s Application ................................ 23
Chapter 5 Console Management ..........................24
5.1 Connecting to the Console Port................... 24
5.2 Pin Assignment............................................ 24
5.3 Login in the Console Interface ..................... 25
5.4 CLI Management.......................................... 26
Chapter 6 Web-Based Management.....................27

6.1 About Web-based Management .................. 27
6.2 Preparing for Web Management.................. 27
6.3 System Login ............................................... 28
6.4 System......................................................... 29
6.5 Time - SNTP ................................................ 32
6.6 Account - Admin........................................... 35
6.7 IP Addressing –IPV4................................... 36
6.8 Syslog .......................................................... 38
Syslog Configuration.................................................... 38
6.9 SNMP Configuration .................................... 39
SNMP - Agent.............................................................. 39
6.20.1 SNMP Trap Configuration............................ 41
6.10 System Alert - Relay Alarm.......................... 42
6.8.1 System Alert - SMTP ..................................... 42
6.8.2 System Alert - Event...................................... 44
6.11 DHCP Server ............................................... 46
6.6.1 DHCP Server - Server configuration.............. 46
6.6.2 Client Table ................................................... 47
6.6.3 IP Bindings .................................................... 47
6.12 Port - Configuration...................................... 49
6.13 Port Status ................................................... 50
6.14 Port Statistics............................................... 51
6.15 Port –Port Alert............................................ 53
6.16 Rate Control –Rate Limit.............................. 54
6.17 Aggregation - Configuration......................... 56
6.17.1 Configuration ............................................... 57

6.17.2 Aggregator –Status..................................... 59
6.18 Spanning Tree.............................................. 60
6.18.1 RSTP Setting............................................... 60
6.18.2 RSTP Information ............................................. 62
6.19 Pro-Ring II S................................................. 63
6.20 Multicast Support ......................................... 65
6.21 LLDP............................................................ 68
6.22.1 LLDP Neighbors.......................................... 69
6.23 Filtering Database........................................ 70
6.24 VLAN............................................................ 72
6.24.1. VLAN Configuration.................................... 72
6.24.2 Switch Status............................................... 75
6.25 QoS.............................................................. 76
6.25.1 Global Settings ............................................ 76
6.25.2 Port Priority ............................................... 77
6.25.3 COS Mapping to Queue............................... 78
6.25.4 DSCP mapping to queue ............................. 79
6.25. Port Mirroring............................................. 81
6.26. Security ..................................................... 82
6.26.1 IP Source Guard - Configuration.................. 82
6.26.2 IP Source Guard –Static Table ................... 83
6.26.3 802.1X/Radius............................................. 84
6.26.4 MAC Filtering.................................................... 87
6.26.5 Port Security................................................ 88
You can block the un-authorized MAC by oer port in
this function. .............................................................. 88
6.27. Maintenance.............................................. 89

6.27.1 Save Configuration ..................................... 89
Troubles shooting....................................................94
Appendix A—RJ-45 Pin Assignment .....................95
RJ-45 Pin Assignments.......................................... 95
RJ-45 Pin Assignment of PoE................................ 98
Appendix B—Command Sets...............................100
Switch Setting Commands Set................................... 100
Admin Password Commands Set .............................. 101
IP Setting Commands Set.......................................... 101
SNTP Commands Set................................................ 102
LLDP Commands Set................................................ 103
Backup & Restore Commands Set ............................ 104
Upgrade Firmware Commands Set............................ 104
DHCP Server Commands Set.................................... 104
Port Control Commands Set...................................... 106
Port Status Commands Set ....................................... 108
Rate Limit Commands Set......................................... 108
Trunk Commands Set................................................ 109
PRO-RING IIS Commands Set.................................. 111
RSTP Commands Set................................................ 111
VLAN Commands Set................................................ 113
SNMP Commands Set............................................... 116
Traffic Prioritization Commands Set........................... 117
IGMP Commands Set................................................ 118
Multicast Static Filtering Table Commands Set.......... 119
IP Security Commands Set........................................ 120
Port Security Commands Set..................................... 121
MAC Blacklist Commands Set................................... 121

802.1x Commands Set .............................................. 122
Fault Alarm Commands Set....................................... 124
System Warning Commands Set............................... 124
Mac Address Table Commands Set........................... 127
Port Statistics Commands Set ................................... 128
Port Monitoring Commands Set................................. 128
System Event Log Commands Set ............................ 129
Ping Commands Set.................................................. 129
SFP Monitor Commands Set ..................................... 129
Loading Average Commands Set.............................. 129
Save Configuration Commands Set........................... 132
Factory Default Commands Set................................. 132
System Reboot Commands Set................................. 132
Logout Commands Set.............................................. 132
FCC Warning

This Equipment has been tested and found to comply with the limits for a
Class-A digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy. It may cause harmful interference to radio
communications if the equipment is not installed and used in accordance
with the instructions. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CE Mark Warning
This is a Class-A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.

1
Chapter 1 Introduction
The 8 10/100TX + 2 10/100/1000T/Dual Speed SFP Combo Managed Industrial Switch
is a cost-effective solution and meets the high reliability requirements demanded by
industrial applications. Using fiber port can extend the connection distance that
increases the network elasticity and performance.
1.1 Hardware Features
Standard
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX/ FX
IEEE802.3ab 1000Base-T
IEEE802.3z Gigabit fiber
IEEE802.3x Flow Control and Back Pressure
IEEE802.3ad Port trunk with LACP
IEEE802.1d Spanning Tree/ IEEE802.1w Rapid Spanning
Tree
IEEE802.1p Class of Service
IEEE802.1Q VLAN Tag
IEEE 802.1x User Authentication (Radius)
IEEE802.1ab LLDP
Switch
Architecture
Back-plane (Switching Fabric): 7.4Gbps
Packet throughput ability(Full-Duplex): 8.3Mpps @64bytes
Transfer Rate
14,880pps for Ethernet port
148,800pps for Fast Ethernet port
1,488,000pps for Gigabit Fiber Ethernet port
Packet Buffer
1Mbits
MAC Address
8K MAC address table
Flash ROM
4Mbytes

2
DRAM
32Mbytes
Connector
10/100TX: 8 x ports RJ-45 with Auto MDI/MDI-X function
10/100/1000T/SFP Combo port: 2 x RJ-45 + 2 x 100/1000
SFP socket with DDM
RS-232 connector: RJ-45 type
Network Cable
10Base-T: 2-pair UTP/STP Cat. 3, 4, 5/ 5E cable
EIA/TIA-568 100-ohm (100m)
100Base-TX: 2-pair UTP/STP Cat. 5/ 5E cable
EIA/TIA-568 100-ohm (100m)
1000Base-TX: 2-pair UTP/STP Cat. 5/ 5E cable
EIA/TIA-568 100-ohm (100m)
Optical Fiber
Distance:
Multi mode:
0 to 5 km, 1300 nm (50/125 μm, 800 MHz*km)
0 to 4 km, 1300 nm (62.5/125 μm, 500 MHz*km)
Single mode:
0 to 40 km, 1310 nm (9/125 μm, 3.5 PS/(nm*km))
0 to 80 km, 1550 nm (9/125 μm, 19 PS/(nm*km))
Min. TX Output:
Multi mode: -20 dBm
Single mode: 0 to 40 km, -5 dBm; 0 to 80 km, -5 dBm
Max. TX Output:
Multi mode: -14 dBm
Single mode: 0 to 40 km, 0 dBm; 0 to 80 km, 0 dBm
Sensitivity:
-36 to -32 dBm (Single mode); -34 to -30 dBm (Multi mode)
Protocol
CSMA/CD
LED
Per unit: Power (Green), Power 1 (Green), Power 2
(Green), Fault (Red), Master (Green), FWD (Green)
8 port 10/100: Link/Activity (Green), Full duplex/Collision
(Amber)

3
SFP port: LNK/ACT(Green), 1000T: LNK/ACT(Green),
1000M(Green)
Power Supply
External Power Supply: DC 12~48V, Redundant power DC
12~48V and connective removable terminal block for
master and slave power
Power
Consumption
9.86 W at full load
Operating
Humidity
5% to 95% (Non-condensing)
Operating
Temperature
-40oC ~ 75oC
Storage
Temperature
-40oC ~ 85oC
Case Dimension
IP-30, 72mm (W) x 105mm (D) x 152mm (H)
Installation
DIN rail and wall mount ear
EMI
FCC Class A, CE EN61000-4-2, CE EN61000-4-3, CE EN-
61000-4-4, CE EN61000-4-5,
CE EN61000-4-6, CE EN61000-4-8, CE EN61000-4-11, CE
EN61000-4-12, CE EN61000-6-2, CE EN61000-6-4
Safety
UL, cUL, CE/EN60950-1
Stability Testing
IEC60068-2-32 (Free fall), IEC60068-2-27 (Shock),
IEC60068-2-6 (Vibration)

4
1.2 Software Features
Management
SNMP v1 v2c, v3/ Web/Telnet/CLI
SNMP MIB
RFC 1215 Trap, RFC1213 MIBII, RFC 1157 SNMP MIB, RFC 1493
Bridge MIB, RFC 2674 VLAN MIB, RFC 1643 , RFC 1757, RSTP MIB,
Private MIB, LLDP MIB
VLAN
Port Based VLAN
IEEE 802.1Q Tag VLAN (256 entries)/ VLAN ID (Up to 4K,
VLAN ID can be assigned from 1 to 4094.)
GVRP (256 Groups)
Port Trunk with
LACP
LACP Port Trunk: 4 Trunk groups/Maximum 4 trunk
members
LLDP
Supports LLDP allowing switch to advertise its identification
and capability on the LAN
Spanning tree
IEEE802.1d spanning tree
IEEE802.1w rapid spanning tree.
Pro-Ring2s
Supports Pro-Ring2s. Provides redundant backup feature
and the recovery time below 20ms
Quality of Service
The quality of service determined by port, Tag and IPv4
Type of service, IPv4 Different Service
Class of Service
Supports IEEE802.1p class of service, per port provides 4
priority queues
Port Security
Supports 100 entries of MAC address for static MAC and
another 100 for MAC filter
Port Mirror
Supports 3 mirroring types: “RX, TX and Both packet”.

5
IGMP
Supports IGMP snooping v1,v2
256 multicast groups and IGMP query
IP Security
Supports 10 IP addresses that have permission to access
the switch management and to prevent unauthorized
intruder.
Login Security
Supports IEEE802.1X Authentication/RADIUS
Bandwidth
Control
Support ingress packet filter and egress packet limit
The egress rate control supports all of packet type and the
limit rates are 100K~102400Kbps(10/100),
100K~256000Kbps(1000)
Ingress filter packet type combination rules are
Broadcast/Multicast/Unknown Unicast packet,
Broadcast/Multicast packet, Broadcast packet only and all
of packet. The packet filter rate can be set from
100K~102400Kbps(10/100), 100K~256000Kbps(1000)
Flow Control
Supports Flow Control for Full-duplex and Back Pressure
for Half-duplex
System Log
Supports System log record and remote system log server
SMTP
Supports SMTP Server and 6 e-mail accounts for receiving
event alert
Relay Alarm
Provides one relay output for port breakdown, power fail
Alarm Relay current carry ability: 1A @ DC24V
SNMP Trap
1. Topology Change
2. Power Trap
3. MAC-Violation
DHCP
Provides DHCP Client/ DHCP Server/ Port and IP Binding

6
DNS
Provides DNS client feature and supports Primary and
Secondary DNS server
SNTP
Supports SNTP to synchronize system clock in Internet
Firmware Update
Supports TFTP firmware update, TFTP backup and restore.
Configuration
Upload/Download
Supports binary format configuration file for system quick
installation
ifAlias
Each port allows importing 128bits of alphabetic string of
word on SNMP and CLI interface

7
1.3 Package Contents
Please refer to the package content list below to verify them against the checklist.
8 10/100TX + 2 10/100/1000T/Dual Speed SFP Combo Managed Industrial
Switch x 1
User manual x 1
Pluggable Terminal Block x 1
Mounting plate x 2
RJ-45 to DB9-Female cable x 1
Compare the contents of the industrial switch with the standard checklist above. If any
item is damaged or missing, please contact the local dealer for service.

8
Chapter 2 Hardware Description
In this paragraph, it will describe the Industrial switch’s hardware spec, port, cabling
information, and wiring installation.
2.1 Physical Dimension
72mm x 105mm x 152mm(W x D x H)
2.2 Front Panel
Front Panel of the industrial switch

9
2.3 Bottom View
The bottom panel of the Industrial Managed Industrial Switch has one terminal block
connector of two DC power inputs and one fault alarm.
Bottom Panel of the industrial switch

10
2.4 LED Indicators
The diagnostic LEDs that provide real-time information of system and optional status are
located on the front panel of the industrial switch. The following table provides the
description of the LED status and their meanings for the switch.
LED
Color
Status
Meaning
PWR
Green
On
The switch unit is power on
Off
No power
R.M.
Green
On
The industrial switch is the master of Pro-
Ring2s group
Off
The industrial switch is not a ring master in
Pro-Ring2s group
PWR1
Green
On
Power 1 is active
Off
Power 1 is inactive
PWR2
Green
On
Power 2 is active
Off
Power 2 is inactive
FAULT
Red
On
Power or port failure
Off
No failure
P9, P10 (RJ-
45)
Green
(Upper LED)
On
A network device is detected.
Blinking
The port is transmitting or receiving packets
from the TX device.
Off
No device attached
Green
(Lower LED)
On
1000M
Off
10/100M

11
Link/Active
(P9, P10
SFP)
Green
On
The SFP port is linking
Blinks
The port is transmitting or receiving packets
from the TX device.
Off
No device attached
P1 ~ P8
Green
On
A network device is detected.
Blinking
The port is transmitting or receiving packets
from the TX device.
Off
No device attached
Amber
On
The port is operating in full-duplex mode.
Blinking
Collision of Packets occurs.
Off
The port is in half-duplex mode or no device
is attached.
FWD (P1 ~
P8)
Green
Green
A powered device is connected utilizing
Power over Ethernet on the port
Off
No device is connected or power forwarding
fails

12
Chapter 3 Hardware Installation
In this paragraph, we will describe how to install the Pro-Ring2s Managed Industrial
Switch and the installation points attended to it.
3.1 Installation Steps
1. Unpack the Industrial switch
2. Check if the DIN-Rail is screwed on the Industrial switch or not. If the DIN-Rail is not
screwed on the Industrial switch, please refer to DIN-Rail Mounting section for DIN-
Rail installation. If users want to wall mount the Industrial switch, please refer to Wall
Mount Plate Mounting section for wall mount plate installation.
3. To hang the Industrial switch on the DIN-Rail track or wall.
4. Power on the Industrial switch. Please refer to the Wiring the Power Inputs section
for knowing the information about how to wire the power. The power LED on the
Industrial switch will light up. Please refer to the LED Indicators section for indication
of LED lights.
5. Prepare the twisted-pair, straight through Category 5 cable for Ethernet connection.
6. Insert one side of RJ-45 cable (category 5) into the Industrial switch Ethernet port
(RJ-45 port) and another side of RJ-45 cable (category 5) to the network device’s
Ethernet port (RJ-45 port), ex: Switch PC or Server. The UTP port (RJ-45) LED on
the Industrial switch will light up when the cable is connected with the network device.
Please refer to the LED Indicators section for LED light indication.
[NOTE]
Make sure that the connected network devices support MDI/MDI-X. If it does not
support, use the crossover category-5 cable.
7. When all connections are set and LED lights all show in normal, the installation is
complete.

13
3.2 DIN-Rail Mounting
The DIN-Rail is screwed on the industrial switch when out of factory. If the DIN-Rail is
not screwed on the industrial switch, please see the following pictures to screw the DIN-
Rail on the switch. Follow the steps below to hang the industrial switch.