Lantronix WiPort Quick setup guide

WiPort™ Integration Guide
Part Number 900-333
Revision G June 2006

Copyright and Trademark
© 2005, 2006, Lantronix. All rights reserved. No part of the contents of this book may
be transmitted or reproduced in any form or by any means without the written
permission of Lantronix. Printed in the United States of America.
WiPort, with its patent-pending technology, is a trademark of Lantronix.
Ethernet is a trademark of XEROX Corporation. UNIX is a registered trademark of
The Open Group. Windows 95, Windows 98, Windows 2000, Windows NT, and
Windows XP are trademarks of Microsoft Corp. Netscape is a trademark of Netscape
Communications Corporation.
Contacts
Lantronix Corporate Headquarters
15353 Barranca Parkway
Irvine, CA 92618, USA
Phone:[phone]
Fax: [phone]
Technical Support
Phone: [phone] or 949-453-7198
Fax: [phone]
Online: www.lantronix.com/support
Email [email protected]
Sales Offices
For a current list of our domestic and international sales offices, go to the Lantronix
web site at www.lantronix.com/about/contact/

WiPort™ Integration Guide 3
Disclaimer
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
 Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
This device is intended only for OEM Integrators. The OEM integrator should be
aware of the following important issues.
Labeling of the End Product
The end product to integrate this module has to be clearly identified on the label that
this end product contains an FCC approved RF module. The format of such
statement could be "Contains Transmitter with FCC ID: R68WIPORTG" or similar.
Integration Note
a) This module is authorized under limited module approval specified to mobile host
equipment. So, the antenna must be installed such that 20cm is maintained between
the antenna and users.
b) The transmitter module may not be co-located with any other transmitter or
antenna.
As long as the 2 conditions above are met, further transmitter testing will not be
required. However, the OEM integrator is still responsible for testing their end-product
for any additional compliance requirements required with this module installed (for
example, digital device emission, PC peripheral requirements, etc.)
Note: In the event that these conditions can not be met (for example certain
laptop configurations, general purpose PCMCIA or similar cards, or co-
location with another transmitter), then the FCC authorization is no longer
considered valid and the FCC ID can not be used on the final product
(including the transmitter) and obtaining a separate FCC authorization.
Note: Changes or modifications to this device not explicitly approved by Lantronix will
void the user's authority to operate this device.

WiPort™IntegrationGuide 4
Contents
1: Introduction 6
About the Integration Guide________________________________________________6
Additional Documentation _________________________________________________6
2: Description and Specifications 7
WiPort Overview ________________________________________________________7
WiPort Block Diagram ____________________________________________________8
PCB Interface __________________________________________________________9
Mating Connector ______________________________________________________10
Serial Input/Output______________________________________________________10
Sample Layouts for RS-485 Connectivity ____________________________________12
WLAN Input/Output _____________________________________________________13
Ethernet Input/Output ___________________________________________________13
Power, Ground, and Reset _______________________________________________14
Absolute Maximum Ratings_______________________________________________14
Recommended Operating Conditions _______________________________________14
Ethernet PHY Receiver Input Characteristics (RX+, RX-) ________________________15
100Base-TX Transceiver Characteristics (TX+, TX-) ___________________________15
Wireless Specifications __________________________________________________15
Technical Specifications _________________________________________________17
Dimensions ___________________________________________________________18
Recommended PCB Layout ______________________________________________19
Product Information Label ________________________________________________20
3: Development Kit 21
Contents of the Kit ______________________________________________________21
Evaluation Board Description _____________________________________________21
Serial Interfaces________________________________________________________21
Power Supply _________________________________________________________22
General Control PLD ____________________________________________________22
Configuration Switch Bank _______________________________________________22
Evaluation Board Layout _________________________________________________23
Evaluation Board Schematics _____________________________________________24
Compliance Information__________________________________________________28
Warranty _____________________________________________________________29

WiPort™ Integration Guide 5
List of Figures
Figure 2-1. WiPort Block Diagram...........................................................................................8
Figure 2-2. Combined RS-232/485 Transceiver ...................................................................12
Figure 2-3. Separate RS-232/485 Transceivers ...................................................................12
Figure 2-4. Separate RS-485 Transceivers for 2-Wire and 4-Wire Setups...........................13
Figure 2-5. Side Views..........................................................................................................18
Figure 2-6. Top View.............................................................................................................18
Figure 2-7. Bottom View........................................................................................................19
Figure 2-8. PCB Layout.........................................................................................................19
Figure 2-9. Product Label......................................................................................................20
Figure 3-1. WiPort Evaluation Board Layout.........................................................................23
Figure 3-2. Evaluation Board Schematics.............................................................................24
List of Tables
Table 2-1. PCB Interface Signals............................................................................................9
Table 2-2. Mating Connectors...............................................................................................10
Table 2-3. Channel 1 Connections........................................................................................11
Table 2-4. Channel 2 Connections........................................................................................11
Table 2-5. Channel 2 RS-422/485 4-Wire Connections........................................................11
Table 2-6. Channel 2 RS-485 2-Wire Connections...............................................................11
Table 2-7. WLAN Signals......................................................................................................13
Table 2-8. Ethernet Signals...................................................................................................13
Table 2-9. Power, Ground, and Reset Pins ..........................................................................14
Table 2-10. Absolute Maximum Ratings ...............................................................................14
Table 2-11. Operating Conditions, Serial Ports, & Configurable Pins...................................14
Table 2-12. Ethernet Input Characteristics............................................................................15
Table 2-13. 100Base-TX Transceiver Attributes ...................................................................15
Table 2-14. Wireless Specifications......................................................................................15
Table 2-15. Technical Specifications ....................................................................................17
Table 3-1. RS-232 Signals....................................................................................................22
Table 3-2. Channel 2 RS-485 4-Wire Connector ..................................................................22
Table 3-3. Channel 2 RS-485 2-Wire Connector ..................................................................22
Table 3-4. Jumper Configurations.........................................................................................22
Table 3-5. Configurable Pin Configurations ..........................................................................23

WiPort™IntegrationGuide 6
1
1: : I In nt tr ro od du uc ct ti io on n
About the Integration Guide
This guide provides the information needed to integrate the WiPort device server
within another product. The intended audiences are the engineers responsible for
integrating the WiPort into their product.
Additional Documentation
The following guides are available on the product CD and the Lantronix Web site
(www.lantronix.com)
WiPort™ Development Kit
Quick Start Guide
Briefly explains the basics to get the WiPort up
and running.
WiPort™ User Guide Provides information needed to configure, use,
and update the WiPort firmware.

WiPort™IntegrationGuide 7
1
1. .2 2: : D De es sc cr ri ip pt ti io on n a an nd d S Sp pe ec ci if fi ic ca at ti io on ns s
The WiPort wireless embedded device server is a complete network-enabling
solution based on the IEEE 802.11b/g wireless standard, with WPA and WEP
capabilities. WiPort allows Original Equipment Manufacturers (OEMs) to add
wireless connectivity to their products by incorporating it onto a circuit board with
minimal engineering.
The WiPort functions independently of a PC, providing an integrated solution that
combines a processor, memory, 802.11b/g transceiver and dual high-speed serial
ports into a single compact module. It includes a wireless connection, an operating
system, an embedded Web server, and a full TCP/IP protocol stack. In addition, the
WiPort sends email alerts and supports numerous other network communication
protocols, including ARP, UDP, TCP, ICMP, Telnet, AutoIP, DHCP, HTTP and
SNMP.
WiPort Overview
The WiPort contains Lantronix’s own DSTni controller with 256 Kbytes of internal
zero wait state SRAM, 16 Kbytes of boot ROM, and integrated 10/100 PHY.
The WiPort also contains the following:
 Two 3.3-volt v24 serial interfaces (5V tolerant)
 Up to 921600 Baud
 16 or 32Mbit flash memory (with optional additional 8Mbit SRAM)
 88 MHz clock
 802.11b interface
 11 configurable pins
 10/100 Ethernet interface
The WiPort requires +3.3-volt power and is designed to operate within a temperature
range of -30ºC to +70ºC.

Description and Specifications
WiPort™ Integration Guide 8
WiPort Block Diagram
The following drawing is a block diagram of the WiPort showing the relationships of
the components.
Figure 2-1. WiPort Block Diagram

Description and Specifications
WiPort™ Integration Guide 9
PCB Interface
Table 2-1. PCB Interface Signals
Pin Number WiPort Pin
Function
Notes
1 3.3V Power Supply input
2 3.3V Power Supply input
3 RTS0 Request “to send” hardware
flow control output (logic
level), serial port 0
4 TXD0 Transmit data output (logic
level), serial port 0
5 RXD0 Receive data input (logic
level), serial port 0
6 CP2 Configurable pin
7 CP3 Configurable pin.
8 CTS0 Clear “to send” hardware flow
control input (logic level),
serial port 0
9 CP10 Configurable pin
10 CP8 Configurable pin
11 Signal Ground
12 Signal Ground
13 Reset In Resets the WiPort unit. Reset
In is low active. Minimum
reset pulse width is 2ms at IIL
= -500 µA
14 CP0 Configurable pin
15 RTS1 Request “to send” hardware
flow control output (logic
level), serial port 1
16 TXD1 Transmit data output (logic
level), serial port 1
17 RXD1 Receive data input (logic
level), serial port 1
18 CP9 Configurable pin
19 CP4 Configurable pin
20 CTS1 Clear “to send” hardware flow
control input (logic level),
serial port 1
21 Reserved Reserved for future use
22 Reserved Reserved for future use
23 Signal Ground
24 Signal Ground
25 Reserved Reserved for future use
26 Reserved Reserved for future use
27 Ethernet Status
LED2
Ethernet activity
28 Ethernet Status
LED1
Ethernet link
29 Ethernet TX- Output
30 Ethernet TX+ Output

Description and Specifications
WiPort™ Integration Guide 10
Pin Number WiPort Pin
Function
Notes
31 Ethernet RX Center
Tap
32 Ethernet TX Center
Tap
33 Ethernet RX- Input
34 Ethernet RX+ Input
35 CP1 Configurable pin
36 WLAN Power LED
(WiPort B only)
High active output, tristated in
Ethernet mode
37 CP6 Configurable pin
38 CP5 Configurable pin.
39 WLAN Activity LED High active output, tristated in
Ethernet mode
40 CP7 Configurable pin
Note: For all the configurable pins, see the WiPort User Guide for selectable
functions.
Mating Connector
Table 2-2. Mating Connectors
Mating Connector Description
Recommended: Samtec FTMH-120-03-F-DV-ES (shrouded
header)
Alternative: Samtec FTMH-120-03-F-DV (not shrouded)
Alternative: Oupiin 2411-2X20GDN/017 (not shrouded)
The mating connector is
a 1mm micro header,
40 pins,
2 x 20.
Serial Input/Output
The unit has two serial ports compatible with V24 serial standards at data rates up to
921Kbps. The serial I/O signals are 3.3V CMOS logic level and pins are 5V tolerant.
Serial signals connect to an internal device, such as a UART. For evaluation and
prototype work, it is convenient to have an external RS-232 interface that can
connect to the serial port on a PC. The WiPort Evaluation Board has one RS-232
and one RS-232/422/485 transceiver (level shifters) to implement this external
interface (only the WiPort 485 supports the RS-422/485 interface).
If desired, use the CPs to create a DTE or DCE-style interface using any 3 available
CPs. To create these interfaces, connect the signals according to Table 2-3 and
Table 2-4.
Note: CPx, CPy, and CPz are any of the available CPs.