Lanzar Mariner AQA430SL User manual

)
'~.,t::R'S MANUAL
MODELS:
AQA430SL
AQA430WT

INTRODUCTION
OurAmplifiers provide high-performance sound reinforcement for your mobile audio
equipment. Its versatility enables compatibility with optional Equalizers,
Frequency Dividing Crossover Networks, and other audio processors in a customized
system. The Multi-Mode bridging capabilities allow flexibility in hosting several dif-
ferent speaker configurations.
To achieve optimum performance, it is highly recommended that you read this
Owners Manual before beginning installation.
WARNING
High powered audio systems in a vehicle are capable of generating "Live Concert"
high levels of sound pressure. Continued exposure to excessively high volume sound
levels may cause hearing loss or damage. Also, operation of a motor vehicle while
listening to audio equipment at high volume levels may impair your ability to hear
external sounds such as; horns, warning signals, or emergency vehicles, thus
contributing to a potential traffic hazard. In the interest
of safety, we recommend lis-
tening at lower volume levels while driving.
2

TABLE OF CONTENTS
PLANNING YOUR SYSTEM ...................................................... .. .......... 3
WIRING CONNECTION ......................................................................... 4
PANEL LAYOUT .........................
.. ............................... .. ...... .. . ... ........ ... ... 5
CONTROL FUNCTIONS ............................................................ 6, 7
SPEAKER CONNECTION
4
CHANNEL CONFIGURATION ..................... 8-10
TROUBLE SHOOTING GUIDE ................................
... ..... ... ........ .. ... . ... .. 11
SPECIFICATION .................. ... .............. ... ................................................ 12
WARNING............................................
.. ........ .. ...................................... 13
PLANNING YOUR SYSTEM
Before beginning the installation, consider the following:
I. Do you plan to add additional mobile electronics equipment in the future?
If you plan to expand your system by adding other components sometime in the
future, ensure adequate space is left and cooling requirements are met.
2. Should you use high or low level inputs?
Your Amplifier has been designed to accept Low-Level(Pre-Amp outputs from your
radio) source signa
l. If your radio/source is equipped with Pre-Amp outputs, it is
possible to utilize them to drive the Amplifier and the 2 front speakers. Then, use the
built-in power
of your radio to drive the 2 rear speakers.
3. Are your components matched?
The RMS power rating
of your speaker(s) must be equal or greater than the RMS
power rating
of your amplifier. Your speaker(s) also must be 2 - 8 Ohms impedance
for stable amplifier operation. Impedance information is normally printed on the
speaker basket
or magnet.
4. Where will the amplifier be installed?
Consider both the length
of your leads, and routing when determining the mounting
location.
It is best to run power and RCA wiring on opposite sides of the vehicle to
prevent induced noise. Pre-amp inputjacks require a length
of high quality shielded
male
to male RCApatch cord.
3

CONNECTING THE POWER
CAUTION:
AS A PRECAUTION, DISCONNECTTHE POWER WIRE FROM THE BATTERY WHILE MAKING THE
POWER AND GROUND CONNECTIONS TO THE AMPLIFIER.
10 GAUGE(Thicker if planning for additional Amplifiers) wire is recommended for
both the power and ground wires.
10 Gauge, for the remote turn-on wire. Both
types are available at most Mobile Audio Dealers or Installation Shop.
(1) Ground: To Vehicle Chassis
To avoid unwanted ignition noise caused by ground loop, it is essential that the
Amplifier
be grounded to a clean, bare, metal surface of the vehicle's Chassis
NOTE:
GROUND WIRE SHOULD NOT BE EXTENDED MORE THAN3 FT. (I METER),
(2) + 12 Volt(Fused) Constant Power: To Battery (+)
Due to the power requirements of the Amplifier, this connection should be made
directly to the positive (+) tenninal
of battery, For safety measures, install an in-line
Fuse Holder (not included) as close to the battery positive (+) tenninal as
possible with an ampere rating; not to exceed total value
of fuses in Amp.
(3) Remote Turn-On Input:
To remote turn-on output of Car Stereo
This Amplifier is turned "ON" remotely when the vehicle's stereo is turned "ON".
NOTE:
IF YOUR RADIO DOES NOT HAVEA +12 VOLT OUTPUT LEAD WHEN THE RADIO IS TURNED ON, THE
"REMOTE"
TERMINAL ON THE AMPLIFIER CAN BE CONNECTED TO VEHICLE'SACCESSORYCIRCUIT THAT IS LIVE
WHEN THE KEY IS "ON".
Remote Turn-oN is
connected to Radio's power
antenna lead or a switchable +12V
Vehicle chassis ground
Fu ..
o
===
o~
o
GND REM BAIT
[~~~I -
~'"~ ]
4
o
"""" {GRUN!
'"""'"
( REO ]

PANEL LAYOUT
AQA430SL AQA430W T FRONT VIEW
AQA430SL AQA430W T RE AR V IE W
~
COJ ~O = = =
GND REM BAn .. •
cg
[~~~ l -0
~"
(G REEN]
..orrcr
o~
, - ' "' ~ ~
(REO]
~o
~'
'@
5

CONTROL FUNCTIONS
I. RCA input jacks
These RCA input jacks are for use with source units that have RCA or Line level
outputs. A source unit with a minimum level
of 180mV is required for proper operation.
The use
of high quality twisted pair cables is recommended to decrease the possibility
of radiated noise entering the system.
2. GAIN Control
The level control wi
ll match the amplifiers sensitivity to the source units signal voltage.
The Operating range
is 180mV minimum to 6V maximum.
CAUT ION: Do n ot run the amplifier in higb volume for long time, otherwise the loudspeakers will be damaged.
3. Full pass x-over switch
When the switch is
in the "Full" position, the full range is bypasse d.
4. Low pass x-over switch
When the switch is in the "LPF" position, frequencies lower than the low pass frequency
setting are passed.
4
.1 Low pass x-over frequency control
This control is used to select the desired low pass x-over frequency.
The frequency can be adjusted between 50Hz and 500H
z.
5. High pass x-over switch
When the switch is in the "HPF" position, frequencies higher than the high pass
frequency setting are passed.
5. 1 High pass x-over frequency control
This control is used to select the desired high pass x-over frequency.
The frequency can be adjusted between 50Hz and 500Hz.
6. Hi Input
Accepts Iv
to I Ov input from the head unit's speaker outpu t.
HIGH INPUT HIGH INPUT
EJ
D
.1eMa .2CHe
elCH9 .«He
I II I
lCHeRED 2C He RED
I II I
3CHeRED 4CHe RED
1 CH e BLACK 2C He BLACK
3CH e BLACK 4CH e BLACK
6

CONTROL FUNCTIONS
7. SPEAKERS
Connect subwoofers to these tenninals.
8.GND
AQA430SL f AQA430WT
GR AY GR EE N /BLACK
W HI TEJ BLA C K~ PU RP LE
W HITE~ PU R PL E/BLACK
GR AY/ BLA CK G REEN
Connect this tenninal directly to the sheet metal chassis of the vehicle, using the
shortest wire necessary to make this connection. Always use wire
of the same gauge
or larger than the (+)12 volt power wire. The chassis connection point should be
scraped free
of paint and dirt. Use only quality crimped and/or soldered connectors
at both ends
of this wire.
Warning: Do not connect this terminal directly to the vehicle battery ground terminal or any otber factory ground
points.
9. Remote Turn On
This tenninal turns on the amplifier when (+)12 volt
is applied to it. Connect it to the
remote turn on lead
of the head unit or signal source.
10. (+)12 Volt Power
Connect this tenninal through a FUSE
or CIRCUIT BREAKER to the positive tenninal of
the vehicle battery or the positive tenninal of an isolated audio system battery.
Warning: Always protect this power wire by installing a fuse or circuit breaker of the appropriate
size within 12 inches of the battery terminal connection.
II. FUSE
These fuses protect the amplifier against internal electrical damage and are meant to
protect the amplifier only. All other power connections should be fused at the source.
AQA430SL I AQA430wr : 40A X I
12. LED
Will illuminate GREEN to indicate the amplifier
is on and operating nonnally, and will
be illuminated RED
ifthe amplifier shuts down due to short circuit, DC offset, or
overheating detected by on board protection circuitry
7

4CHANNEL STEREO CONFIGURATION for AQA430SL / AQA430wr
•
- I 1 ---·
_ 04 -12d8 3685 (QJl2SJ •
_{jff)CD CD CDCDCDCD
2·8 Ohms
1CH
2-8 Ohms
2CH
2-8 Ohms
3CH
=
""
2-8 Ohms
4CH
o
HIGH INPUT n0
~ Uo
•
101
6$
001
9
I. Channel 112 and channel 3/4 lowest recommended impedance is 20hm stereo.
2. Crossover mode, output, and gain configurations are independently adjustable between the
front and rear channels.
3. Channels
112 and channels 3/4 outputs can be individually configured for high-pass, low-
pass, or full range operation.
8

4CHANNEL BRIDGED CONFIGURATION for AQA430SL / AQA430wr
~ .
- I 1 ---·
_ 04'12dB3685 12J16l •
~(jJj) CDCDmCDmCD
+
4-8 Ohms
1CH/2CH
4-8 Ohms
3CH/4CH
""
I. Channel 112 and 3/4 outputs can be configured for high.pass, lowpass, or full range operation.
2. Channel 112 outputs are configured for summed bridged operation for subwoofer.
3. Channel 3/4 outputs are configured for summed bridged operation for subwoofer.
9

4CHANNELTRI MODE CONFIGURATION for AQA430SL / AQA430wr
CAPACITOR
HIGH PASS FILTER
INDUCTOR
lOW PASS FILTER
2·8 Ohms
1CH
•
- I 1 ---·
_ 04· 12dB 3685 ISZ1I2SI •
""
==
SPE AII;ER
GAI N
~ ~
MI N MAX MI N MAX
e n_ e
~.IQl .IQl~
50Hz sootil LPf FUll HPF U'f FU ll HPF 50Hz SOOH .
(1/X111 IJI4CII)
X-oVER _ _ X -oVE R
2-8 Ohms
2CH
2-8 Ohms
3CH
o
HIG HINP UT ~ 0
~ 0
$lOte$4CH9
4-8 Ohms
WOOFER
2-8 Ohms
4CH
1. Lowest recommended impedance is 20hm stereo and 40hrn bridged mono.
2. Front and rear outputs must be set for full range operation.
3. Passive crossovers must be used on all components and frequencies must not overlap.
10

TROUBLE SHOOTING GUIDE
No power to power wire
11
Check fuses in amplifier.
Be sure Turn-on lead is connected
Repair power wire or connections
Check connections to radio
Inspect for short circuit
or an
open connect
ion.
Reverse Left and Right
RCA inputs to determine
if it is
occurring before the amp.
Check TunerfDeck volume level.
Clean contacts on fuse holders.
Be sure proper speakers are used
to ensure impedance
recommendations are observed.
(If you use an Ohmmeter to
check speaker resistance,
please remember that DC
resistance andAC impedance
may not be the same.)

SPECIFICATIONS
MODEL# AQA430SL I AQA430wr
MAXIMUM POWER OUTPUT
1600W
POWER OUTPUT@ 40hm
300WX4CH
POWER OUTPUT @2 0hm
600WX4CH
BRIDGED POWER @ 40hm 1200Wx2CH
THD O. 05%THD+N
FREQUENCY RESPONSE -1.OdB
20Hz-40KHz
HPF
50-500Hz
LPF
50-500Hz
ADJUSTABLE SENSITIVITY RANGE
180mV - 6V
INPUT IMPEDANCE (LOW LEVEL)
18k
FUSE
40AX lEA
DIMENSION(Hx W x Linch )
1.73 X 6.22 X 8.03
WARNINGS
Investigate the layout of your automobile thoroughly before drilling or cutting
any holes. Take care when to worknear the gas tanks, lines, or hydraulic
lines,
and electrical wiring. Don't use power amplifier unmounted. Attach
this system securely to the automobile
to prevent damage, particularly in
the event of an accident. Don't mount this system so that the wire
connections are unprotected
or are subject to pinching or damagefrom
nearby objects. The +12V
DC power wire must be fused at the battery
positive terminal connection. Before making
or breaking power connections
at this system power terminals, disconnect the +12V wire
at the battery end.
Confirm your radiolcassette player and/or other equip is turned
off while
connecting the input
jacks and speaker terminals. If you need to replace
the
power fuse, replace it only with afuse identical to that suppliedwith the
system. Using afuse
of different type or rating may result in damage to this
system which isn't covered by the warranty.
12