Lanzar VBXEQ4P User manual

4BandAdjustableParametricEqualizer
with Subwoofer Gain Control

www.Lanzar.com
2
Table of Contents
1. Introduction
2. Features
3. Detailed Features
4. Installation
5. System
6. Warning
Introduction
You have made a ne choice of a quality product.
Our VBXEQ4P equalizer is a truly innovative product with:
• Superb specications for audio quality
• Lots of features for versatile applications
• And a nice design nish.
Therefore please make the best of this top notch device!
Our equalizer stands out from the average not just because of its exclusive physical
appearance, but because of outstanding technique with handy features for a
wide range of 12 Volt applications. Please be sure to read al operating instructions
and understand all safety precautions before installing and operating your new
VBXEQ4P equalizer. Although our equalizer is easy to install on your own, we
recommend you use an Audio Bank authorized dealer for optimum performance
of your new unit.
2
3
4
5
6
7

www.Lanzar.com
3
Features
• 4 Band Adjustable Parametric Equalizer
• Half Din Size
• 7 Volt RMS Pre-Amp Output
• Pre-amp Line Aux Inputs Via RCA & Phone Jacks
• 3 Input Sources Selectable
• Input Gain Adjustments
• RCA AUX Input Jack
• Source/Aux Input Selector
• Rotary Fader
• Output Volume Control
• Sub Output Volume Control
• Blue Light Illumination
• DC 12 Volt with Remote trigger
• Mounting Hardware Included
• RCA Auxiliary Input (Rear) inputs for MP3, DVD, or Phone
What's in the Box:
• 4-Band Parametric Equalizer
• 2 Mounting brackets
• 8 Phillips-head Screws
• Power Red Wire with 1A Fuse
Technical Specs:
• Bass Equalizer Frequency: 20Hz~ 60Hz
• Mid-Bass Equalizer Frequency: 100Hz ~ 300Hz
• Mid Equalizer Frequency: 1 KHz ~ 2 KHz
• High Equalizer Frequency: 7 KHz ~ 20 KHz
• Each Frequency Adjustable: -12dB to +12dB
• Output Voltage: 7V RMS @ 0.05% THD
• Operating Voltage: 11V-15V
• S/N Ratio: 110dB
• Separation: > 60dB
• Frequency Response: 10Hz ~ 50 KHz
• Subwoofer Frequency: 35Hz ~ 250Hz
• Product Dimensions: 7'' x 4.1''x 1.10'' -inches

www.Lanzar.com
4
Detailed Features
17
16151413121110
1 2 3 4 65 7 8 9 12
1. Volume Control
2. Fader Control
3. Main/ DVD switch
4. Sub Level Control
5. Low-Pass Frequency Adjustment
6. Bass Frequency Adjustment
7. Mid-bass Frequency Adjustment
8. Mid Frequency Adjustment
9. High Frequency Adjustment
10. DVD Gain Controls
11. Main Input
12. DVD input
13. Front Output
14. Rear Output
15. Sub Output
16. Power Plug
17. Equalizer Frequency Controls

www.Lanzar.com
5
Installation
Mounting Precautions
This in-dash EQ can be mounted next to the source unit or under the dash with
the supplied mounting brackets. For easy set-up, mount the equalizer so the
front panel controls will be easily accessible for the driver's seat after installation.
In addition, observe the following precautions.
1. Check the clearance on both sides of a planned installation before drilling any
holes or installing any screws.
2. When routing RCA cables, keep them away from power cables and output
speaker wires.
3. Do not allow liquids or foreign objects to enter the unit.
4. If the unit should become wet, turn o all the power and call your local
authorized dealer so they can check for any possible damage.
Wiring Precautions
Read all of the following wiring precautions. If you are not sure about any of
the installation or wiring processes, please contact your local dealer for help.
1. This unit operates on an automotive 12V negative ground power source and
requires additional audio components for proper operation.
2. Disconnect the negative (-) lead of the battery before making any power
connections.
3. A good chassis ground connection is critical to the performance of your in-dash
EQ. Use the shortest ground wire possible and securely connect the car chassis
along with the source unit to minimize resistance and avoid noise problems.
4. Extra cable can cause signal loss and act as an antenna for noise.
Use only high quality RCA cables that are no longer than needed.
5. If you are using a source unit without a remote turn-on lead, the in-dash EQ
can be turned on with a switched accessory lead.

www.Lanzar.com
6
System Setup
Setting System Volume
After completing the system wiring, follow the steps below to properly adjust
the in-dash EQ.
1. Turn the master volume control on the in-dash EQ and the amplier gain
controls to their minimum setting.
2. Turn the source unit on and increase the volume until distortion is heard, then
reduce the volume just below this point. This is the maximum usable musical
signal for this source unit. Turning the volume beyond this point will increase
distortion without an increase in musical signal. Once the source unit volume
has been set, it will no longer be used. Always use the volume control on the
in-dash EQ as the master (main) volume control. It has better electronics, a
higher SIN ratio, and is more linear than any source unit volume available.
Setting Equalizer Controls
1. Begin by setting all frequencies to the center or level position.
2. Play a favorite music track that you know well and adjust the individual EQ
controls as desired. Avoid extreme settings that can distort musical peaks.
3. Increase or decrease the EQ gain controls as necessary.
4. If your system includes a subwoofer, slowly increase the subwoofer control
until you hear solid bass.
5. If your system includes rear speakers, adjust the fader control to add rear sound.
Set it so most of the music comes from the front and only lls in the rear.

www.Lanzar.com
7
Setting the Low-Pass Frequency
This in-dash EQ has a built-in low-pass crossover located on the front of the
unit. Set the crossover (60Hz - 90Hz) upon the type and size of your subwoofer
system.
1. Plug the additional video source into the DVD input located on the back
of the unit.
2. With the Main/DVD switch in the MAIN position, turn the equalizer volume to
a normal listening volume.
3. With the video source in play mode, switch to the DVD input source.
4. With the Main/DVD switch in the DVD position, adjust the input gain controls
located on the top of the panel so that the volume of the DVD source matches
the volume of the Main source.
WARNING
Investigate the layout of your automobile thoroughly before drilling or cutting
nay holes,' Take care when you work near the gas tanks, gas lines, hydraulic lines,
and electrical wiring. Attach the system securely to the automobile to prevent
damage, particularly in the event of an accident. Do not mount the system so
that the wire connections are unprotected or are subject to pinching or damage
from nearby objects.
The + 12VDC power wire must be fused at the battery positive terminal
connection. Before making or breaking power connections at the system power
terminals, disconnect the + 12V wire at the battery end. Conrm your radio/head
unit and/or other equipment is turned o while connecting the input jacks and
speaker terminals.
|f you need to replace the power fuse, replace it only with a fuse identical to that
supplied with the system. Using a fuse of dierent type or rating may result in
damage to this system which is not covered by the warranty.

Questions? Issues?
We are here to help!
Phone: [phone]
Email: [e-mail]