LapSafe ClassBuddy User manual

LapSafe® Self-Service Solutions Ltd
3 Wakes Hall Business Centre
Wakes Colne
Colchester
Essex
CO6 2DY
[email protected] lapsafe.com0800 130 3456
ClassBuddy™ Wall
Installation Guide
2019 v2.0

2 3
Introduction
Decide on a suitable location for your ClassBuddy™ Wall to be mounted.
The unit must be fixed to a solid wall or directly to studs, if the unit is being
fitted to a non-solid wall. The use of hollow wall or plaster board type
fixings are not recommended. Allow space above and below the wall unit
for ventilation.
Ensure that you check the wall prior to any drilling and fixing for electrical
cables or other services that may be in the wall/void. Make sure the the
unit is at an acceptable user height.
Select suitable fixings for the wall that you are fixing to and ensure that
you use a minimum of 8 of the possible 16 fixing positions available.
(Ensuring as even distribution as possible).
IMPORTANT Two persons are required to carry out the installation.
Tools required
• Power or battery type drill (hammer required for solid walls)
• Drill-bit to suit your fixing type (refer to manufacturer’s instructions)
• Pencil/Pen (to mark hole positions)
• Spirit level
• Hammer
• Screwdriver/Power Driver
• Vacuum cleaner
Weight
28kg
Step 1: Stand Up
Once unpacked, stand the unit up and ensure you have a clear working
space around all sides.
Copyright Lapsafe® Self Service Solutions

5
Step 3: Unscrew holding nuts
On the bottom right hand side of the unit there are two holding nuts that
need to be unscrewed, these are just finger tight. Once you have done this,
lock the doors back up.
Step 2: Open Doors
Open the le hand side door with the white key, and then open the right
hand side door with the blue key.
4
Holding Nuts

76
Step 6: Mark Drill Holes
Use a pencil or marker to mark all the fixing holes then remove the
Mounting Bracket.
Step 5: Level The Mounting Bracket
Hold the mounting bracket up against the wall with the bottom lip facing
towards you and use a spirit level to make sure the bracket is level on the
wall and ensure the hanging slots are at the top.
You may need two people for this
Step 4: Unhook Mounting Bracket
Unhook the mounting bracket by tilting the ClassBuddy™ Wall forward
and pushing the mounting bracket down.
1. Tilt Forward
2. Push bracket

8 9
Step 9: Secure Mounting Bracket
Place the mounting bracket back onto the wall with the bottom lip facing
towards you, and screw your fixings into place in accordance with the
manufacturer's instructions.
Step 8: Insert Fixings
Fit fixings into place in accordance with the manufacturer's instructions.
Step 7: Drill Holes
Drill the required holes for fixings in accordance with the manufacturere's
instructions. Ensure an even distribution of fixings and use a minimum
number of 8.
Step 10: Hook ClassBuddyTM Wall
Once the mounting bracket is secured li the ClassBuddy™ Wall into place.
There are six hooks along the sides that the unit slides onto.
Two peope are required to li the ClassBuddy ™ Wall
Ensure that ClassBuddy™ Wall is hooked on correctly and that the three
lower studs are through the fixing holes before gently releasing the unit.

10 11
Complete
Your new ClassBuddy™ Wall should now be successfully installed onto
your wall and you are ready to load your cables and devices. Please refer
to the user guide that is supplied with your ClassBuddy™ Wall for further
information. Please read the Health and Safety guidance in the User
Manual.
If you have any problems please do not hesitate to contact our support
team.
Step 11: Secure
Once in place, open both doors again (Step 2) and screw the two holding
nuts on to the studs that you removed in Step 3.
Replacement Keys
lapsafe.com/support/keys
Support Enquiries
lapsafe.com/support/enquiry
[email protected]om
0800 130 3456

LapSafe® Self-Service Solutions Ltd
3 Wakes Hall Business Centre
Wakes Colne
Colchester
Essex
CO6 2DY
[email protected] lapsafe.com0800 130 3456