Larson Electronics LED25WRE-LENSCOVER User manual

LED25WRE-LENSCOVER
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
1of 2
Snap on Polycarbonate Filter for LED25WRE Series LED Light Fixtures
Multiple Colors - Spot/Flood
Instruction Manual
Thank you for your purchase of the Larson Electronics LED25WRE-LENSCOVER.
)
WARNING:
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CRITICAL SAFETY INSTRUCTIONS:
•INSTALLATION SHOULD ONLY BECONDUCTED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NEC AND ANY
RELEVANT LOCAL BUILDING CODES.
•RISK OFFIRE OR ELECTRIC SHOCK. FIXTURE INSTALLATION REQUIRES KNOWLEDGE OF FIXTURE'S ELECTRICAL
SYSTEMS. IFNOTQUALIFIED, CONTACT A QUALIFIED ELECTRICIAN.
•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.
•MAKE SURE THE SUPPLY VOLTAGE IS THE SAME AS THE FIXTURE'S RATED VOLTAGE.
•TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR SHARP
OBJECTS. SUITABLE FOR DAMP LOCATIONS.
IMPORTANT
READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE. THE LED25WRE-LENSCOVER MUST BE WIRED IN ACCORDANCE WITH NATIONAL ELECTRICAL
CODE AND ALL APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.
WE STRONGLY ENCOURAGE ONLY ALICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS
PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET,
CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.
WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE
INSTALLATION OR PERFORMING ANY MAINTENANCE.
RISK OF FIRE/ELECTRIC SHOCK –DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.
RISK OF PERSONAL INJURY –FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOT INSTALLED PROPERLY.
RISK OF BURN –ALLOW FIXTURE TO COOL BEFORE SERVICING.
WARNING:
READ CAREFULLY BEFORE OPERATING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CRITICAL SAFETY INSTRUCTIONS:
Never place spotlight face down when light is on. Doing so could burn/ignite surfaces such as seats, carpeting,
etc. and cause major property damage. Always turn spotlight off when not in use.
To prevent serious damage to eyesight, never look into spotlight when light is on.
DO NOT shine light into the face of someone else.
DO NOT touch lens of spotlight when light is on or if it was recently on. The lens will be hot.
DO NOT allow children to handle or operate this spotlight.
DO NOT use this product for other than its intended use.
DO NOT operate in close proximity of combustible or flammable materials.
DO NOT attempt to operate this spotlight if cord, plug, battery, bulb or any part of the spotlight is damaged or
corroded.

LED25WRE-LENSCOVER
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
2of 2
Snap on Polycarbonate Lens for LED25WRE Round LED Light Fixtures -
Multiple Colors - Spot/Flood Lens
These snap on lenses fit over the face of the LED25WRE round LED
light fixtures. These snap on lenses are offered in clear, blue, amber, and
red color options and in euro, spot, flood, elliptical, and wide flood beam
configurations. Each lens is constructed of scratch resistant
polycarbonate and is designed to snap onto the front of the light fixture.
Please note, these lenses are designed for the LED25WRE.
Clear lenses diffuse the light without changing the color. In the spot
configuration, the clear lens is used to protect the face of the light fixture.
Blue lenses are best suited for snow and arctic conditions. Operators will
experience less glare and reflection from the snow, and will be more
noticeable to oncoming traffic.
Amber lenses are best suited for fog and water environments. The
amber color penetrates the fog better than higher color temperatures,
reducing glare and increasing visibility under high fog conditions.
Red lenses are best suited for dust. The red color pierces through the
dust and improves visibility where other colored light sources may
provide low to zero visibility.
INSTALLATION
•Disconnect fixture from power and ensure it is cool to the touch.
•Remove the old lens and replace with desired new replacement lens.
•Reconnect fixture to power and continue use.
MAINTENANCE
There are no serviceable parts inside the fixture. However, it is good practice to routinely clean and check the
fixture for proper function.
•Disconnect power running to the lamp and be sure the fixture is cool to the touch.
•Use a non-abrasive glass cleaning solution to clean the lens.
USE AND CARE
Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.
Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of
children when not in use.Inspect for good working condition prior to storage and before re-use.
REPLACEMENT PARTS
The LED25WRE-LENSCOVER is designed to provide years of reliable performance. Should the need for replacement
parts arise, please contact Larson Electronics.
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.
SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT
[e-mail] OR BY PHONE AT 1-800-369-6671 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.