Larson Electronics WAL-QP-4XWP60E-25-1227 User manual

WAL-QP-4XWP60E-25-1227
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
1of 3
240 Watt LED Work Area Tripod Light Fixture
500 Watt Quartz Halogen Replacement - Waterproof
Instruction Manual
The WAL-QP-4XWP60E-25-1227 Tripod Mounted LED Work Area Light from Larson Electronics produces
21,600 lumens of bright flood light and is an economical direct replacement for 500 Watt quartz halogen flood
lamps. This adjustable LED light tower is designed for portability and durable operation and ideal for use in
demanding conditions.
WARNING: Read all instructions carefully
SAVE THESE INSTRUCTIONS
CAUTION: RISK OF ELECTRICAL SHOCK
•Do not use with extension cord near water or
where water may accumulate.
•Keep plugs and receptacles dry.
•For use only on GFCI protected circuits.
•Risk of burns, do not operate without lens.
•Lighted lamp is hot. Keep away from
combustibles. Unplug to change bulb.
WARNING RISK OF FIRE, ELECTRIC SHOCK,
EXPOSURE.
•Unit operates on 120/277 VAC 50/60Hz only
•Unplug and allow cooling before replacing bulb.
•Do not touch hot lens guard or enclosure.
•Do not remain in light if skin feels warm.
•Do not look directly at lighted lamp.
•Do not operate the lamp with missing or
damaged lens or lamp containment barrier.
TRIPOD ASSEMBLY
The tripod assembly consists of 3 parts:
1. Light head
2. Pole w/Legs
3. Wheel base
To assemble tripod, begin by placing the legs over the wheel base. Tighten bolt to secure the wheels.
The tripod can now be rolled around on its wheels. Ensure the legs are folded up before tilting tripod
to maneuver.
WARNING: Use caution before tilting tripod with a heavy load. For heavy loads, it is recommended to
remove the light head prior to transporting via wheel base! Failure to do so may cause serious injury
or death. Larson Electronics shall not be held liable for injuries caused by misuse.
1. Place tower in desired location that is flat and able to support the tripod without falling over.
2. Loosen hand screw and lower legs until firmly stabilizing tripod.
3. Tighten hand screw to secure legs.
4. With help, place the light head over top pole and tighten hand screw.
Light weight lamps can be attached by tilting tripod toward the ground with the legs up. Attach light
head to pole, tighten hand screw and tilt back to its vertical position. DO NOT tilt tripod while
extended to max height. It is recommended to have another person hold the tripod while tilting
vertically.
For heavy weight lamps, use a ladder and extra help for attaching light head to pole.
Double check that all hand screws are tight before continuing use of the light tower.

WAL-QP-4XWP60E-25-1227
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
2of 3
EXTENDING
1. Loosen hand screw for extending the light head. Once loose, extend light head until desired
height is achieved with at least 1ft - 2ft remaining inside pole for support.
WARNING: DO NOT over extend light head completely allowing extension pole to free from base! If
the light head becomes free, serious injury or death can occur. Larson Electronics shall not be held
liable for injuries caused by misuse.
2. When desired height is achieved, tighten hand screw to secure light head.
LOWERING
1. To lower mast, grasp light head and slowly loosen hand screw. Lower the light head and
tighten hand screw.
WARNING: DO NOT loosen hand screw allowing light head to fall freely. This can damage the unit
and cause serious injury or death. Always grasp light head before lowering. Larson Electronics shall
not be held liable for injuries caused by misuse.
The tripod mount light tower can be disassembled for storage or transporting. Unplug light from power
source and remove light head following previous steps for attaching.
Once the light head has been removed, loosen hand screw for legs and fold them up. Wheel to
desired location or remove from wheel base for complete disassembly.
THE LENS AND CORD MUST BE ROUTINELY CHECKED FOR CUTS, BREAKS, SCRATCHES OR ANY
SEVERE ABRASIONS, AND IF ANY ARE FOUND, THE PARTS MUST BE REPLACED BEFORE
RESUMING USE OF THE LIGHT TOWER.
WIRING (see attached wiring diagram)
This unit comes preconfigured with 25 feet SOOW Cord and your chosen configuration of cord cap.
Once deployed, plug cord cap into compatible receptacle with Voltage: 120/277 VAC 50/60Hz
WARNING: CHECK NAMEPLATE
FOR PROPER VOLTAGE. DAMAGE
FROM IMPROPER VOLTAGE WILL
VOID WARRANTY.

WAL-QP-4XWP60E-25-1227
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
3of 3
MAINTENANCE
Caution: To avoid personal injury, disconnect power to the light and allow the unit to cool down
before performing maintenance.
Warning: No user serviceable parts inside of fixture. Risk of electric shock. Removal of the lens
will void the warranty.
1. Perform visual, mechanical and electrical inspections on a regular basis. We recommend
routine checks to be made on a yearly basis. Frequency of use and environment should
determine this. It is recommended to follow an Electrical Preventive Maintenance Program
as described in NFPA 70B: Recommended practice for Electrical Equipment.
2. The lens should be cleaned periodically as needed to ensure continued photometric
performance. Clean the lens with a damp, non-abrasive, lint-free cloth. If not sufficient, use
mild soap or a liquid cleaner.
3. Inspect the cooking fins on the luminaire to ensure that they are free of any obstructions
or contamination (i.e. excessive dust build-up). Clean with a non-abrasive cloth if
needed.
4. Do not operate if the lens is cracked or damaged. All fasteners should be properly seated.
REPLACEMENT PARTS
The WAL-QP-2X-25 is designed to provide years of reliable performance. Should the need for
replacement parts arise, please see part numbers below and attached drawings in next section.
Some parts may be sourced locally from your nearby hardware store.
Description:
Part Number:
Tripod assembly:
ALU-TP-W-712
Should the need for replacement parts not listed arise, please contact Larson Electronics at the
contact information below.
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS. SHOULD FURTHER
INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT [e-mail] OR BY PHONE
AT 1-800-369-6671 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.