Larson Electronics EPL-WPLED-100W-RT-DIMM User manual

EPL-WPLED-100W-RT-DIMM
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
1of 4
100W Explosion Proof LED Wall Pack Light
Surface Mount - 11,667 Lumens - C1D1 - 0-10V Dimmable
Instruction Manual
Thank you for your purchase of the Larson Electronics EPL-WPLED-100W-RT-DIMM.
WARNING:
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CRITICAL SAFETY INSTRUCTIONS:
•INSTALLATION SHOULD ONLY BECONDUCTED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NEC AND ANY
RELEVANT LOCAL BUILDING CODES.
•RISK OFFIRE OR ELECTRIC SHOCK. FIXTURE INSTALLATION REQUIRES KNOWLEDGE OF FIXTURE'S ELECTRICAL
SYSTEMS. IFNOTQUALIFIED, CONTACT A QUALIFIED ELECTRICIAN.
•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.
•MAKE SURE THE SUPPLY VOLTAGE IS THE SAME AS THE FIXTURE'S RATED VOLTAGE.
•TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR SHARP
OBJECTS. SUITABLE FOR DAMP LOCATIONS.
IMPORTANT
READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE. THE EPL-WPLED-100W-RT-DIMM MUST BE WIRED IN
ACCORDANCE WITH NATIONAL ELECTRICAL CODE AND ALL APPLICABLE LOCAL
CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.
WE STRONGLY ENCOURAGE ONLY ALICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS
PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET,
CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.
WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE
INSTALLATION OR PERFORMING ANY MAINTENANCE.
RISK OF FIRE/ELECTRIC SHOCK –DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.
RISK OF PERSONAL INJURY –FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOT INSTALLED PROPERLY.
RISK OF BURN –ALLOW FIXTURE TO COOL BEFORE SERVICING.
WARNING:
USER SHOULD BE TRAINED IN THE PROPER USE AND MAINTENANCE OF THIS DEVICE. THIS LINE
CORD IS INTENDED TO ALLOW OPERATORS TO EXTEND POWER TO EQUIPMENT WHEN STATIONARY OUTLETS ARE NOT
READILY AVAILABLE.
IMPROPER USE OF THIS CORD, PLUG, AND RECEPTACLE CAN LEAD TO SERIOUS INJURIES OR DEATH TO
PERSONNEL.
PERIODIC INSPECTION OF THE CORD IS NECESSARY.
THE CORD MUST BE ROUTINELY CHECKED FOR CUTS, BREAKS, OR ANY SEVERE ABRASIONS, AND IF ANY ARE FOUND,
THE CORD MUST BE REPLACED BEFORE RESUMING USE.

EPL-WPLED-100W-RT-DIMM
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
2of 4
WARNING
TO AVOIDTHE RISKOF FIRE,EXPLOSION OR ELECTRIC SHOCK, THIS PRODUCT SHOULD BE INSTALLED,
INSPECTEDAND MAINTAINEDBY A QUALIFIED ELECTRICIANONLY, IN ACCORDANCEWITHALL
APPLICABLEELECTRICAL CODES.
TO AVOIDELECTRIC SHOCK:
•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.
•PRODUCT MUST BE CONNECTED TO A WIRING SYSTEM WITH AN EQUIPMENT-GROUNDING
CONDUCTOR.
TO AVOID EXPLOSION:
•MAKE SURE THE SUPPLY VOLTAGE IS WITHIN THE VOLTAGE RATING.
•ENSURE THE MARKED T RATING IS LESS THAN THE IGNITION TEMPERATURE OF THE HAZARDOUS
ATMOSPHERE.
•DO NOT OPERATE IN AMBIENT TEMPERATURES ABOVE THOSE INDICATED ON THE PRODUCT
NAMEPLATE.
•DO NOT OPERATE IF THE LENS, CORD, SEALS, HOUSING, RECEPTACLES, ETC. IS CRACKED OR
DAMAGED. IF SO, DISCONTINUE USE AND CONTACT MANUFACTURER FOR REPLACEMENT PARTS.
•ALL FASTENERS SHOULD BE PROPERLY SEATED.
The EPL-WPLED-100W-RT-DIMM from Larson Electronics is an Explosion Proof LED Dimmable Wall Pack Light
Fixture that provides operators with a powerful and energy efficient alternative to traditional hazardous location
luminaries. Cree LED technology and compact design makes this lamp an excellent replacement upgrade option for
bulky and high maintenance cost older fixtures. The EPL-WPLED-100W-RT-DIMM features 0-10V dimming
capabilities.
WIRING
Standard pigtail(flying leads) wiring
We strongly encourage a licensed electrician install this product,in all locations especially in outdoor
areas where weatherproofing may be required. Universal voltage driver permits operation at 100V - 277V AC, 50
or 60Hz, or 11-25 Volts AC/DC.
Low Voltage DC
Connect power to power supply outputting low voltage between 11-25 VoltsDC.
This variable voltage allows greater versatility without affecting light output. Ensure
deutsch connectors are properly connected (If applicable).
MOUNTING
The EPL-WPLED-100W-RT-DIMM offers several mounting options including ceiling
mounting, pendant mounting, wall mounting and cable mounting. The standard
version of this explosion proof LED fixture includes a trunnion mount wall/flat surface
bracket.

EPL-WPLED-100W-RT-DIMM
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
3of 4
Use only 0-10V Dimmer appropriate for the location installed.
WARNING: Mis-wiring Low Voltage Dimming Control could cause permanent damage to light.
DO NOT connect dimming control to line voltage.
DO NOT connect dimmer with power applied.
WIRE(AC) WIRE(DC) COLORED CABLE
AC LIVE DC LIVE BLACK
AC NEUTRAL DCNEUTRAL WHITE
GROUND GROUND GREEN
DIMMING + DIMMING + RED
DIMMING - DIMMING - ORANGE
WARNING: CHECK NAMEPLATE FOR PROPER VOLTAGE.
DAMAGE FROM IMPROPER VOLTAGE WILL VOID WARRANTY.
DIMMING
This LED light fixture features 0-10V dimming capabilities. This gives operators the ability to manually adjust
the brightness of the LED lamp quickly and easily. The 0-10V dimming allows for adjustments to fit the
brightness needs of any lighting situation. A 0-10V dimmable light works through the use of a DC control signal
that ranges between zero and ten volts. The basic idea is that at 10 volts of input the light is at its brightest level
with 0 volts being the lowest possible dimness setting. The smooth, continuous and flicker-free dimming of a
0-10V dimmable LED light is ideal for a wide range of different lighting applications.
Voltage: Check product label for correct voltage.
WIRING (see attached wiring diagram)
This unit comes preconfigured in selected voltage and beam configuration. Wire light tothe correct
voltage. Follow all applicable local, state, and National Electrical Code for the hazardous area.
Wire size is 18/5.

EPL-WPLED-100W-RT-DIMM
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
4of 4
MAINTENANCE
Caution: To avoid personal injury, disconnect power to the light and allow the unit to cool down before
performing maintenance.
Warning: No user serviceable parts inside of fixture. Risk of electric shock. Removal of the lens will void
the warranty.
1. Perform visual, mechanical and electrical inspections on a regular basis. We recommend routine
checks to be made on a yearly basis. Frequency of use and environment should determine this. It is
recommended to follow an Electrical Preventive Maintenance Program as described in NFPA 70B:
Recommended practice for Electrical Equipment.
2. The lens should be cleaned periodically as needed to ensure continued photometric performance.
Clean the lens with a damp, non-abrasive, lint-free cloth. If not sufficient, use mild soap or a liquid
cleaner.
3. Inspect the cooling fins on the luminaire to ensure that they are free of any obstructions or
contamination (i.e. excessive dust build-up). Clean with a non-abrasive cloth if needed.
4. Do not operate if the lens is cracked or damaged. All fasteners should be properly seated.
USE AND CARE
Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.
Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of
children when not in use.Inspect for good working condition prior to storage and before re-use.
REPLACEMENT PARTS
The EPL-WPLED-100W-RT-DIMM is designed to provide years of reliable performance. Should the need for
replacement parts arise, please contact Larson Electronics.
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.
SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT
[e-mail] OR BY PHONE AT 1-800-369-6671 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.