Laserworld Pro-700RGB User manual

Pro-700RGB
User manual
Please read this manual carefully before use!

User manual: Pro-700RGB
Rev: 01/2009
Page
2
of
9
Contents
Page
SAFET INSTRUCTIONS ....................................................................................... 3
OPERATING THE LASER ....................................................................................... 3
Using the laser ..................................................................................................... 4
Control Panel ....................................................................................................... 4
ILDA mode .......................................................................................................... 5
DMX mode........................................................................................................... 5
Maintenance / cleaning......................................................................................... 5
Technical specifications ........................................................................................ 6
Change scanner ................................................................................................... 6
Adjustable mirror mounts ..................................................................................... 6
Troubleshooting ................................................................................................... 7
ILDA signal .......................................................................................................... 7
Technical diagram ................................................................................................ 8
Please note.......................................................................................................... 8
EU-declaration of conformity................................................................................. 9
Checking parts
Please check if all listed parts are included, and are not damaged.
Included:
1 x Pro-700RGB Laser
1 x Power cable
1 x 9-pin plug
2 x key
1 x safety cord
1 x manual

User manual: Pro-700RGB
Rev: 01/2009
Page
3
of
9
AFETY IN TRUCTION
If the device has been exposed to great temperature changes, do not switch it on
immediately. Condensation water may damage your device. Leave the device
switched off until it has reached room temperature.
The laser must only be used for shows. Any operation has to be attended and
supervised by a skilled and well-trained operator.
Never leave this device running unattended and keep it away from children and
unauthorized persons.
Keep away from heaters and other heat sources. In order to safeguard sufficient
ventilation, leave 50 cm of free space around the device.
Never direct the laser beam to people or animals.
CAUTION LASER DIODE: Don’t open the housing!
There are no serviceable parts inside the device. Maintenance and service operations
shall only be carried out by authorized dealers. If you open the device for cleaning,
always disconnect from mains!
- HEALTH HAZARD! Never look directly into the light source, as
sensitive persons may suffer an epileptic shock!
These lasers are considered a definite eye hazard,
particularly at the higher power levels, which WILL cause
eye damage. So these laser series models supplied with a
key switch to prevent unauthorized use, warning labels
and aperture labels affixed to the laser.
Installation safety
Prior to installation and operation of the laser, the paths of
the beams and effects should be considered, particularly with respect to how they
will reach the audience. If direct audience scanning is desired, then the laser energy
in the effects needs to be considered to decide if the effects are safe for direct
viewing.
OPERATING THE LA ER
The operator has to make sure that laser radiation – also reflected laser radiation –
higher than the maximum permissible level is avoided by technical or organisational
measures.
Make sure to use the correct voltage
If the device is used in a flying installation, the mounting brackets and an
appropriate safety-rope must be fixed.
In some countries, the operator must notify the accidence insurance and the
authority for industrial safety, before operating a laser. For more information, contact
the relevant authorities.
Please consider that unauthorized modifications on the device are strictly forbidden
due to safety reasons!
If this device will be operated in any way differently than described in this manual,
the product may suffer damages and the guarantee becomes void. Furthermore, any
other operation may lead to dangers like short-circuit, burns, electric shock, etc.

User manual: Pro-700RGB
Rev: 01/2009
Page
4
of
9
Keep surrounding dry and clean. This unit should be kept dry, do not use in the rain
or damp and dusty environment. Projector should be put in a water-proof housing
when operated outside.
Operating temperature is 10~35°C. Let laser cool off 10minutes after 2 hours of
operation, to ensure maximum lifetime for the diode.
Distance between laser aperture and projection screen should be not less than 1
meter.
Do not turn device on and immediately off again frequently.
Do not look into the laser beam directly, especially not with optical instruments.
Do not touch the device with wet hands.
When the laser diode becomes dim or broken, please contact your dealer timely.
When returning laser to dealer/manufacturer always use original packaging.
Maintenance should be performed every 15-day period. Use a sponge with alcohol,
rather than wet cloth or other chemical liquid, to clean the mirror.
Using the laser
Make sure the correct voltage is used. Connect mains. Connect an emergency switch
to the 9-pin connector on the backside (pins 1, 2). If you do not wish to connect an
emergency switch, connect the 9-pin plug. Depending on the mode selected (see
below), laser light should come out of the
opening on the front panel – be careful.
Control Panel
•MODE: select mode, or go up in menu
•ENTER: confirm changes, or go down in menu
•UP/ DOWN: change DMX address
Operating modes:
Test mode: a built-in test pattern is displayed
“DMXAddr“: DMX512 mode-. Here you can change the DMX
address:
“Open“: change address
“Up“ & “down“: increase/decrease address
“Save“: save new address
1 ecurity switch: Laser on/off
2 Remote lock: connect emergency switch. If no
emergency switch is connected use the 9 pin plug
supplied.
3 DMX In/Out: DMX512-Standard signal
4 Power switch: power on/off
5 Power: connect to mains. Make sure the correct
voltage is used
6 ILDA connector in/out

User manual: Pro-700RGB
Rev: 01/2009
Page
5
of
9
ILDA mode
When an IDLA compatible interface is connected to the laser, the laser is
automatically switched to ILDA mode. Output is then controlled from a PC running
software.
The laser uses pins 4 and 17 of the IDLA signal to detect the presence of an ILDA
interface.
Further information can be found in the software manual.
DMX mode
Channel DMX512 value Function
1 brightness 0~255 0-100% brightness
0~1 No change Single colour/RG : strobe
2~255 Strobe from slow to fast
0~25 Original colour
26-207 Colours
2
RGB: colour
208~233; 208~233 Colour change; colour flow
0~42 Pattern group 1
43~85 Pattern group 2
86~128 Pattern group 3
129~171 Pattern group 4
3 Pattern group
172~214 Pattern group 5
4 Pattern 0~255 32 patterns
5 Horizontal rotation 0~255 slow to fast
6 Vertical rotation 0~255 slow to fast
7 Z rotation 0~255 slow to fast
8 Horizontal move 0~255 slow to fast
9 Vertical move 0~255 slow to fast
10 Horizontal stretch 0~255 slow to fast
11 Vertical stretch 0~255 slow to fast
12 Hor. and vert. stretch 0~255 slow to fast
13 Drawing speed 0~255 slow to fast
14 Point draw 0~255 slow to fast
15 Scanspeed 0~255 slow to fast
0~1 Original size 16 Pattern size
2~255 Size (120= original)
Maintenance / cleaning
Always disconnect from mains before cleaning/opening the laser. Regularly clean the
interior from dust, especially ensure operation of the fans. Use a sponge with
alcohol, rather than wet cloth or other chemical liquid, to clean the mirrors. Be
careful, even light scratches reduce the output power of the laser. Mirrors need
cleaning, when a “halo” is noticeable around the beam, or an unusual high amount
of diffuse light can be seen inside the device.

User manual: Pro-700RGB
Rev: 01/2009
Page
6
of
9
Technical specifications
• Output power: typical: 700mW, guaranteed: 470mW, 100mW 632nm green,
70mW 473nm blue, 300mW 650nm red
• Lasersources: aircooled DPSS laser
• Laser class: 4
• Modes: ILDA, DMX 512
• ILDA: 25pin ILDA standard Sub-D shaped 25pin connector
• Galvos: 50k scanspeed
• DMX 512: 16 channels
• Patterns: 160
• canangle: set to ca. 40° optical (60° max)
• Beam: ca. 3mm/1mrad
• Accessories: power cable, key switch, interlock plug, manual, safety cord
• The laser comes in a flightcase.
• Input voltage: AC 100~240V 50/60Hz
• Power consumption: 145W
• ize: 670 x 380 x 270 mm (W x D x H)
• Weight: 20kg Laser, total: 35kg (with flightcase)
• Operating temperature: 10°-35°C
• Temperatur: 10°-35°C
Change scanner
1. Unscrew UK M6 screws and
disconnect signal cable.
2. Loosen M4 x 10 screw and remove
galvo.
3. Insert galvo, reconnect and fix
signal cable.
4. Rotate galvo to center projection.
Fix galvo.
Adjustable mirror mounts
1. Loosen setscrews, then adjust with X/
adjustable screws. Make sure beam is
centered on scanner mirrors.
2. Adjust Z-screw simultaneously.
3. Tighten setscrews.
4. When combining beams (RG /RGB
laser), first make sure the beams are
(roughly) on the same spot on the
mirrors/dichros. Then use a test pattern
(e.g. rectangle) to do fine adjustment.
For adjustments, always turn output
power down (if possible).

User manual: Pro-700RGB
Rev: 01/2009
Page
7
of
9
Troubleshooting
Problem Possible reason Damaged part Replacement
Fuse blown Fuse 09-00-3001-01 No power
Power supply defective +-24V 16-03-0039-00
Microphone defective Microphone 16-03-0001-00
Control board defective Control board 26-2A-LT12V2-00
Potentiometer defective Potentiometer 04-03-0104-01
Music mode not working
CPU defective IC 00-89C516RD-00
Scanner defective Galvo 15-01-2215-00
CPU defective IC 00-89C516RD-00
Control board defective Control PCB 26-2A-LT12V2-00
Power supply defective +-24V 16-03-0039-00
X and/or axis no
deflection
Scanner driver board defective Scanner driver board 26-2A-6800A-00
Lenses / mirrors dirty Clean with alcohol
Laser diode defective Laser diode Inquire
Control board defective Control board 26-2A-LT12V2-00
Laser dark or dim
Configuration / wrong mode Check configuration (see
paragraph control panel)
Configuration / wrong mode Check configuration (see
paragraph control panel)
Control board defective Control PCB 26-2A-LT12V2-00
Power supply defective +-24V 16-03-0039-00
Display board defective Display 26-2A- X2012DI-00
No output
Pins 4 and 17 of the ILDA signal
not connected
See below
Laser does not switch to ILDA mode:
•The interface does not connect pins 4 and 17 (Interlock) of the IDLA signal. See
interface manual
•The cable does not connect pins 4 and 17. Use a cable that connects pins 4 and 17.
•Use an adapter that connects pins 4 and 17.
ILDA signal
Pin out of the standard ILDA signal:
1 Scanner X+ -10V..+10V 14 X- +10V..-10V
2 Scanner + -10V..+10V 15 - +10V..-10V
3 Intensity/Blanking+ 0V..+2.5V 16 Intensity/Blanking- 0..-2.5V
4 Interlock A 17 Interlock B
5 Red+ 0..2.5V 18 Red- 0..-2.5V
6 Green+ 0..2.5V 19 Green- 0..2.5V
7 Blue+ 0..2.5V 20 Blue- 0..-2.5V
8 – 12 Not used 23-24 Not used
13 Shutter +5V, max. 20 mA 25 GND Signal ground

User manual: Pro-700RGB
Rev: 01/2009
Page
8
of
9
Technical diagram
Please note
This device has left our premises in absolutely perfect condition. In order to maintain
this condition and to ensure a safe operation, it is absolutely necessary for the user
to follow the safety instructions and warning notes written in this user manual.
Laserworld cannot be made liable for damages caused by incorrect installations and
unskilled operation!

User manual: Pro-700RGB
Rev: 01/2009
Page
9
of
9
EU-declaration of conformity
We hereby confirm that the following device
Laserworld Pro-700RGB
complies with the essential safety requirements, laid down in the regulations of the
committee to assimilate the provisions of law of all participating EU states on the
electromagnetic compatibility (89/336/EWG).
The device has been classified considering the following EU-norms on
electromagnetic compatibility:
DIN EN 61000-3-2:2000 + A2: 2005
DIN EN 61000-3-3:1995 + A1: 2001
Assessment of compliance of the product with the requirements relating to the Low Voltage
Directive (LVD 2006/95/EG) was based on the following standards:
DIN EN 60065 : 2002
Furthermore, the device is verified in correspondence to the laser class regulations DIN EN
60825-1, if properly set up according to the upper mentioned laser safety regulation.
After installing the device, an inspection and official approval is indispensable for the overall
setup. The inspection must follow the european guidelines EN 60825-1 and corresponding
regulations for the prevention of accidents BGV-B2.
This declaration is executed on behalf of the Laserworld Pro-700RGB manufacturer
Laserworld ( witzerland) AG
Oberstrasse 1
8274 Tägerwilen
SCHWEIZ
Vertretungsberechtigte Personen:
Verwaltungsrätin Rhea Gössel
Sitz des Unternehmens: 8274 Tägerwilen / Schweiz
Firmennummer: CH-440.3.020.548-6
Handelsregister Kanton Thurgau
www.laserworld.com
[e-mail]
Bevollmächtigter im Sinne des EMVG:
Cleantech Europe GmbH
Geschäftsführer: Thomas Schulze
Fürkhofstr. 5
81927 München / DE