Launch Creader Professional 919 MAX User manual

LAUNCH
i
Copyright Information
Copyright © 2023 by LAUNCH TECH. CO., LTD (also called LAUNCH for short).
All rights reserved. No part of this publication may be reproduced, stored in a
retrieval system, or transmitted in any form or by any means, electronic,
mechanical, photocopying, recording or otherwise, without the prior written
permission of LAUNCH.
Statement: LAUNCH owns the complete intellectual property rights for the
software used by this product. For any reverse engineering or cracking actions
against the software, LAUNCH will block the use of this product and reserve the
right to pursue their legal liabilities.
Disclaimer of Warranties and Limitation of Liabilities
All information, illustrations, and specifications in this manual are based on the
latest information available at the time of publication.
The right is reserved to make changes at any time without notice. We shall not
be liable for any direct, special, incidental, indirect damages or any economic
consequential damages (including the loss of profits) due to the use of the
document.

LAUNCH
ii
Using This Manual
This manual contains device usage instructions.
Some illustrations shown in this manual may contain modules and optional
equipment that are not included in your system.
The following conventions are used.
Bold Text
Bold text is used to highlight selectable items such as buttons and menu options.
Example:
Tap OK.
Notes and Important Messages
Notes
A NOTE provides helpful information such as additional explanations, tips, and
comments.
Example:
Note: Remember to remove the VCI connector from the vehicle’s DLC after use.
Warning
Warning indicates a hazardous situation which, if not avoided, could result in
minor or moderate injury to the operator or to bystanders.
Example:
Warning: Retrieving and using DTCs for troubleshooting vehicle operation is only
one part of an overall diagnostic strategy. Never replace a part based only on the DTC
definition. Each DTC has a set of testing procedures, instructions and flow charts that
must be followed to confirm the location of the problem. This information can be found
in the vehicle’s service manual.
Danger
Danger indicates an imminently or potentially hazardous situation which, if not
avoided, could result in death or serious injury to the operator or to bystanders.
Example:
Danger: If you must drive the vehicle in order to perform a troubleshooting
procedure, always have a second person help you. Trying to drive and operate the
diagnostic tool at the same time is dangerous, and could cause a serious traffic accident.

LAUNCH
iii
Illustrations
Illustrations used in this manual are samples, the actual testing screen may vary
for each vehicle being tested. Observe the menu titles and on-screen
instructions to make correct option selection.
Important Safety Precautions
To avoid personal injury, property damage, or accidental damage to the product,
read all of the information in this section before using the tool.
DANGER
• When an engine is operating, keep the service area well-ventilated or attach
a building exhaust removal system to the engine exhaust system. Engines
produce various poisonous compounds (hydrocarbon, carbon monoxide,
nitrogen oxides, etc.) that cause slower reaction time and result in death or
serious personal injury.
• Please use the included battery and power adaptor. Risk of explosion if the
battery is replaced with an incorrect type.
• DO NOT attempt to operate the tool while driving the vehicle. Have second
personal operate the tool. Any distraction may cause an accident.
WARNING
 Always perform automotive testing in a safe environment.
 Do not connect or disconnect any test equipment while the ignition is on or
the engine is running.
 Before starting the engine, put the gear lever in the Neutral position (for
manual transmission) or in the Park (for automatic transmission) position to
avoid injury.
 NEVER smoke or allow a spark or flame in vicinity of battery or engine. Do
not operate the tool in explosive atmospheres, such as in the presence of
flammable liquids, gases, or heavy dust.
 Keep a fire extinguisher suitable for gasoline/chemical/electrical fires nearby.
 Wear an ANSI-approved eye shield when testing or repairing vehicles.
 Put blocks in front of the drive wheels and never leave the vehicle unattended
while testing.
 Use extreme caution when working around the ignition coil, distributor cap,

LAUNCH
iv
ignition wires and spark plugs. These components create hazardous voltage
when the engine is running.
 To avoid damaging the tool or generating false data, please make sure the
vehicle battery is fully charged and the connection to the vehicle DLC (Data
Link Connector) is clear and secure.
 Automotive batteries contain sulfuric acid that is harmful to skin. In operation,
direct contact with the automotive batteries should be avoided. Keep the
ignition sources away from the battery at all times.
 Keep the tool dry, clean, free from oil, water or grease. Use a mild detergent
on a clean cloth to clear the outside of the equipment when necessary.
 Keep clothing, hair, hands, tools, test equipment, etc. away from all moving or
hot engine parts.
 Store the tool and accessories in a locked area out of the reach of children.
 Do not use the tool while standing in water.
 Do not expose the tool or power adapter to rain or wet conditions. Water
entering the tool or power adaptor increases the risk of electric shock.
 This tool is a sealed unit. There are no end-user serviceable parts inside. All
internal repairs must be done by an authorized repair facility or qualified
technician. If there is any inquiry, please contact the dealer.
 Keep the tool far away from magnetic devices because its radiations can
damage the screen and erase the data stored on the tool.
 Do not attempt to replace the internal rechargeable lithium battery. Contact
the dealer for factory replacement.
 Do not disconnect battery or any wiring cables in the vehicle when the ignition
switch is on, as this could avoid damage to the sensors or the ECU.
 Do not place any magnetic objects near the ECU. Disconnect the power
supply to the ECU before performing any welding operations on the vehicle.
 Use extreme caution when performing any operations near the ECU or
sensors. Ground yourself when you disassemble PROM, otherwise ECU and
sensors can be damaged by static electricity.
 When reconnecting the ECU harness connector, be sure it is attached firmly,
otherwise electronic elements, such as ICs inside the ECU, can be damaged.

LAUNCH
v
FCC Statement
FCC ID: XUJX431PROV5
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The
highest reported SAR for stand-alone and simultaneous transmission exposure
conditions are below the maximum value. End-users must be informed of the
operating requirements for satisfying RF exposure compliance.
This device is in compliance with the essential requirements and other relevant
provisions of Radio Equipment Directive 2014/53/EU. The RF frequencies can
be used in Europe without restriction.

LAUNCH
vi
TABLE OF CONTENTS
1 Introduction................................................................................................... 1
1.1 Product Profile .........................................................................................1
1.2 Package List ............................................................................................2
1.3 Components & Controls ..........................................................................4
1.3.1 Display Tablet ...................................................................................4
1.3.2 VCI Connector .................................................................................5
1.4 Technical Parameters ..............................................................................7
2 Initial Use ...................................................................................................... 8
2.1 Charging & Turning On ............................................................................8
2.2 Screen Layout .........................................................................................8
2.3 Basic Gestures ........................................................................................8
2.4 Change System Language ......................................................................9
2.5 Adjust Brightness ....................................................................................9
2.6 Set Standby Time ....................................................................................9
2.7 Network Setup ....................................................................................... 10
3 Getting Started ............................................................................................ 11
3.1 Register & Update ................................................................................. 11
3.2 Home Screen ........................................................................................ 13
4 Connections ................................................................................................ 15
4.1 Preparation ............................................................................................ 15
4.2 Vehicle Connection................................................................................ 15
5 Diagnosis .................................................................................................... 18
5.1 Intelligent Diagnose ............................................................................... 18
5.2 Local Diagnose ...................................................................................... 21
5.2.1 Health Report (Quick Test) ............................................................. 24
5.2.2 System Scan .................................................................................. 26
5.2.3 System Selection ........................................................................... 27
5.3 Diagnostic History.................................................................................. 35
5.4 Feedback .............................................................................................. 35

LAUNCH
vii
6 Service (Reset) Function ............................................................................ 37
7 Software Update ......................................................................................... 38
7.1 Update Diagnostic Software & APP ....................................................... 38
7.2 Update Frequently Used software ......................................................... 39
7.3 Renew Subscription............................................................................... 39
8 User Info ...................................................................................................... 40
8.1 My Report .............................................................................................. 40
8.2 VCI ........................................................................................................ 40
8.3 VCI Management .................................................................................. 40
8.4 Activate VCI........................................................................................... 40
8.5 Firmware Fix.......................................................................................... 40
8.6 My Order ............................................................................................... 41
8.7 Subscription Renewal Card ................................................................... 41
8.8 Profile .................................................................................................... 41
8.9 Change password.................................................................................. 41
8.10 Settings ............................................................................................... 41
8.10.1 Units ............................................................................................. 41
8.10.2 Shop Information .......................................................................... 41
8.10.3 Printer Set .................................................................................... 41
8.10.4 Clear Cache ................................................................................. 42
8.10.5 About ............................................................................................ 42
8.10.6 Login/Logout ................................................................................ 42
8.11 Diagnostic Software Clear ................................................................... 42
9 Other Modules ............................................................................................ 43
9.1 Testable Models .................................................................................... 43
9.2 Tablet Setting ........................................................................................ 43
9.3 Files....................................................................................................... 43
9.4 System Upgrade .................................................................................... 43
9.5 Recording Master .................................................................................. 43
9.6 Calculator .............................................................................................. 43
9.7 Browser ................................................................................................. 43

LAUNCH
viii
9.8 Gmail ..................................................................................................... 44
9.9 Camera ................................................................................................. 44
9.10 Gallery ................................................................................................. 44
9.11 Toolbox ............................................................................................... 44
9.11.1 TPMS ........................................................................................... 44
9.11.2 BST360 (Battery Tester) ............................................................... 44
9.11.3 Videoscope................................................................................... 44
10 FAQ ............................................................................................................ 45

LAUNCH
1
1 Introduction
1.1 Product Profile
It inherits from LAUNCH’s advanced diagnosing technology and is characterized
by covering a wide range of vehicles, featuring powerful functions, and providing
precise test result.
Through simple wireless/wired communication between VCI (Vehicle
Communication Interface) device and the display tablet, it achieves full car
model and full system vehicle trouble diagnosis, which include Reading DTCs,
Clearing DTCs, Reading Data Stream, Actuation Test and Special Functions.
It has the following features:
 Intelligent Diagnose: This module allows you to use the VIN information of the
currently identified vehicle to access its data (including vehicle information,
historical diagnostic records) from the cloud server to perform quick test,
eliminating guesswork and step-by-step manual menu selection.
 Local Diagnose: Follow the on-screen prompts to start diagnostic session
step by step.
 Service Function: It offers coding, reset, relearn and more service functions,
to help vehicles get back to functional status after repair or replacement.
Available tests vary by vehicle manufacturer, year, and model.
 One-click Update: Lets you update your diagnostic software online.
 Mall: Enables you to subscribe some extra software or service functions that
are not integrated in the tool online.
 Diagnostic History: This function provides a quick access to the tested
vehicles and users can choose to view the test report or resume from the last
operation, without starting from scratch.
 Feedback: Enables you to submit the vehicle issue to us for analysis and
troubleshooting.
 Testable Models: Quick dial to view the vehicle models that the tool covers.

LAUNCH
2
1.2 Package List
The following packing list is for reference purpose only. For different destinations,
the accessories may vary. For details, please consult from the seller or check the
packing list supplied with this tool together.
Display tablet x 1
Indicates the test result.
VCI connector x 1
A device for accessing vehicle live
data.
Diagnostic
cable
x 1
Connects the VCI connector to
vehicle’s OBD II diagnostic socket.
It can be separated into two parts:
HDB15F to HD15F data cable and
HD15M to OBD II adaptor.

LAUNCH
3
Password envelope x 1
A piece of paper bearing the product
Serial Number and Activation Code
for product registration.
Power adaptor (Varies with sales
regions)
Charges the tablet via AC outlet.
Type
-
A to Type
-
C USB cable
x 1
• Connects the diagnostic tool to AC
outlet / PC for charging / data
exchange.
• Connects the VCI connector to the
diagnostic tool to perform vehicle
diagnosis.
Quick Start Guide x 1

LAUNCH
4
1.3 Components & Controls
There are two main components to the diagnostic system:
 Display Tablet – the central processor and monitor for the system (See
Chapter 1.3.1).
 VCI Device – the device for accessing vehicle data (See Chapter 1.3.2).
1.3.1 Display Tablet
The tablet acts as the central processing system, which is used to receive and
analyze the live vehicle data from the VCI device and then output the test result.
1. Microphone
2. Type-A USB Port
• Connect to the VCI connector to perform vehicle diagnosis via the USB cable.
• Connect to an external USB storage device for data exchange.
3. Type-C USB Port
• Connect to AC outlet for charging.
• Connect to PC for data exchange.

LAUNCH
5
4. POWER Key
• In Off mode, press it for 3 seconds to turn the tablet on.
• In On mode:
• Press it once to activate the LCD if the LCD is off. Press it once to turn off
the LCD if the LCD lights up.
• Press and hold it for 3 seconds to turn it off.
• Press and hold it for 8 seconds to perform forced shutdown.
5. LCD Screen
Indicate the test result.
6. Speakers
7. Rear Camera
8. Microphone
1.3.2 VCI Connector
The VCI connector works as a vehicle communication interface device, which is
used to connect to the vehicle’s DLC (Data Link Connector) socket via the
diagnostic cable to read the vehicle data and then send it to the tablet.

LAUNCH
6
1. OBD-15 diagnostic connector
Connect on vehicle’s OBD II DLC via the diagnostic cable.
2. USB port
Connect the VCI to the tablet to perform vehicle diagnosis via USB cable.
3. I/O indicator
• Illuminates blue when the VCI is communicating with the tablet wirelessly.
• Illuminates red when the VCI is connected to the tablet via USB cable.
4. VEHICLE indicator
Illuminates green and flashes when the VCI is communicating with the vehicle.
5. POWER indicator
Illuminates solid red while the VCI is powered up.

LAUNCH
7
1.4 Technical Parameters
Display Tablet
Operating system: Android
Memory: 4GB
Storage: 64GB
Screen: 7 inch capacitive touch screen with a resolution of 1024 x 600 pixels
Camera: Rear-facing 8.0MP camera
Connectivity:
• Wi-Fi (802.11a/b/g/n/ac)
• Bluetooth
Working temperature: 0℃ ~ 50℃
Storage temperature: -20 ~ ℃70℃
VCI Connector
Working voltage: 9 ~18V
Power consumption: ≤2.0W
Dimension: 118.3mm*69.5mm*32mm
Working temperature: 0℃ ~ 50℃
Relative humidity: 20% ~ 90%

LAUNCH
8
2 Initial Use
2.1 Charging & Turning On
1. Use the included power adaptor to charge the tablet.
2. After charging is complete, press the POWER button to turn the tablet on.
The system starts initializing and then enters the home screen.
Note: If the battery remains unused for a long period of time or the battery is
completely discharged, it is normal that the tool will not power on while being charged.
Please charge it for a period of 5 minutes and then turn it on.
Warning: Please use the included power adaptor to charge your tool. No
responsibility can be assumed for any damage or loss caused as a result of using power
adaptors other than the one supplied.
Press the POWER button for 3 seconds, an option menu will pop up on the
screen. Tap Power off/Restart to turn it off/reboot it.
2.2 Screen Layout
There are five on-screen buttons available on the bottom of the screen.
Home: Navigates to the Android’s home screen.
Recent App: Views the running applications.
VCI Connection: Shows whether the VCI device is properly connected or
not. If displayed in green, it indicates the communication between the tablet and
the VCI is established.
Screenshot: Captures the current screen.
Back: Returns to the previous screen.
2.3 Basic Gestures
Single-tap: To select an item or launch a program.

LAUNCH
9
Double-tap: To zoom in so that the text on a webpage appears in a
column that fits your tablet’s screen.
Long press: Tap and hold on the current interface or area until a
contextual menu pops up on the screen, and then release it.
Slide: To jump to different pages.
2.4 Change System Language
The tool supports multiple system languages. To change the language of the
tool, please do the following:
1. On the home screen, tap Other Modules -> Settings -> System ->
Language & input -> Languages.
2. Tap Add a language, and then choose the desired language from the list.
3. Tap and hold the desired language and drag it to the top of the screen and
then release it, the system will change into the target language.
2.5 Adjust Brightness
Note: Reducing the brightness of the screen is helpful to conserve the battery
power.
1. On the home screen, tap Other Modules -> Settings -> Display ->
Brightness level.
2. Drag the slider to adjust it.
2.6 Set Standby Time
If no activities are made within the defined standby period, the screen will be
locked automatically and the system enters sleep mode to save power.
1. On the home screen, tap Other Modules -> Settings -> Display ->
Advanced -> Sleep.

LAUNCH
10
2. Choose the desired sleep time.
2.7 Network Setup
The tablet has built-in Wi-Fi that can be used to get online. Once you’re online,
you can register your tool, surf the Internet, get apps, and check for software
updates etc.
1. On the home screen, tap Other Modules -> Settings -> Network & Internet
-> WLAN.
2. Slide the Wi-Fi switch to ON, the tablet starts searching for available wireless
networks.
3. Select a wireless network,
 If the chosen network is open, the tablet will connect automatically.
 If the selected network is encrypted, a network password will need to be
entered.
4. When Connected appears, it indicates the Wi-Fi connection is complete.
Note: When Wi-Fi is not required, this should be disabled to conserve battery
power.

LAUNCH
11
3 Getting Started
For new users, you will need to experience a user registration process before
getting started.
3.1 Register & Update
Follow the steps below to sign in and update:
Tap Login on the upper right corner of the home screen, the following login
window will pop up.
(If you are a new user, follow A to proceed.)
(If you have registered to be a member, go to B to login the system directly.)
(In case you forgot password, refer to C to reset a new password.)
A. If you are a new user, tap New Registration to enter the sign-up page.
Fill in the information in each field (Items with * must be filled). After inputting,
tap Register, the following screen will appear:

LAUNCH
12
Input the 12-digit Product Serial Number and 8-digit Activation Code (can be
obtained from the password envelope), and then tap Activate.
Tap OK to navigate to the update center to update all available software. Refer
to Chapter 7 for detailed operations.
After the registration is successfully complete, the wireless communication
between the tablet and the VCI device is automatically established and user has
no need to configure it again.