Lawmate PV-1000 Touch User manual

User Manual
PV-1000Touch
User Manual
PV-1000Touch
LawMate, innovation never stops!

1. Power Button
2. Stop/Rec Button
3. Screen Lock
4. HDMI Out
5. Control Port
6. Digital Cam In
7. Analog Cam In
8. Camera LED
9. A/V In
10. A/V Out
11. Infrared Sensor
12. Reset Button
13. Battery Compartment
14. 5” Touch Screen
15. Memory Card Slot
16. Speaker
17. DC In
18. USB Port
19. LED Status Bar
1. Names and Parts
Power Stop Rec Lock HDMI-TV Control
12 3 4 5
6
7
8
9
10
11
1213
14
15
16
17
18
19

2. Package Content
European Standard
Adapter Head
USB Cable
Infrared Remote
Controller
A/V In Cable
Earphone
A/V Out Cable
3
DC5V 3A Charger Pouch
Stylus Pick Battery Pack
3.7V Li-ion BATTERY PACK
Capacity 4400 mAh
BA-4400slim
CAUTION..
Do not crush, puncture, incinerable
or short external contact
CAUTION..Risk of electric shock dry
location use only.
Cell From Japan Made in Taiwan
2013a

3. Basic Operation
Power On: Press Power On / Off button on the unit to
turn on the device.
Power Off: Press Power On / Off button on the unit to
turn off the device.
When the device is turned on, it enters Main Menu page.
Touch the screen to select the desired function.
A. Power On / Off Device
B. Select Function
C. Adjust Volume
When playing back the video on unit, touch icons on the unit
or press on the remote control to adjust volume

3. Basic Operation 2
D. Output to Monitor
E. Connect to PC
1. Touch Sengs on the Main Menu, enter “Display”
and choose “TV” as input end.
2. Plug the RCA cable into AV-Out port and connect
the other end to the monitor to output the image.
F. Charging
1. Connect two ends of the USB cable to PC and
PV-1000Touch
2. “USB Mode” noficaon appears to indicate
PV-1000Touch is properly connected to PC.
1. When the power goes down, baery bar on the interface goes down. Please charge the DVR immediately.
Before the device shuts down, red LED will blink for 3 seconds and shows a noficaon “Baery Very Low.”
2. Connect the DVR with the power supply via DC5V 3A Charger, red LED will illustrate to show the DVR is charging.

4. Operation- Recording
1. Connect a 5V analogue camera to cam in port or a LawMate digital camera to digital cam in port
2. Power on the device by pressing .
3. To start recording, switch to Rec.
4. Touch on the screen to start recording and switch to Stop
Power Stop Rec Lock HDMI-TV Control
1
2
3
3
21
4
4
4

1
5. Introduction to all Setting Functions
Enter Settings Page
1. Preview
Select your preferable preview mode among the sections.
Resolution ( 320x240 / 640x480 / 720x480 / 1024x768 / 1280x720 / 1280x960 )
Quality(High/Normal/Low)
Frame Rate( 1 / 5/ 15 /20/30)
Audio (Enable/Disable)
Frame Counter Stamp (On/Off)
Timestamp (On/Off)
Device ID Stamp (On/Off)
Microphone Sensitivity
Overwrite

2
2. Pre-event
Features
As soon as the record function is triggered, the video automatically traces back 5
seconds or 15 seconds before the record button is pressed.
Note: This function is activated after 15 seconds of recording.
Resolution ( 320x240 / 640x480 / 720x480 / 1024x768 / 1280x720 / 1280x960 )
Quality(High/Normal/Low)
Frame Rate( 1 / 5/ 15 /20/30)
Audio (Enable/Disable)
Frame Counter Stamp (On/Off)
Timestamp (On/Off)
Device ID Stamp (On/Off)
Pre-event Duration(5sec / 15 sec)
Microphone Sensitivity
Overwrite

3
3. Pre-Motion
Features
As soon as a movement is derected, recording starts. The video automatically traces
back 5 or 15 seconds before the record button is pressed.
Note: This function is activated after 15 seconds of recording.
Resolution ( 320x240 / 640x480 / 720x480 / 1024x768 / 1280x720 / 1280x960 )
Quality(High / Normal / Low)
Frame Rate ( 1 / 5/ 15 /20/30)
Audio (Enable/ Unable)
Frame Counter Stamp (On/Off)
Timestamp (On/Off)
Device ID Stamp (On/Off)
Pre-Event Duration( 5sec /15sec)
Motion Detect Level(High / Medium / Low)
Microphone Sensitivity
Overwrite(Disable/Enable)

4
4. Motion Detection
Resolution ( 320x240 / 640x480 / 720x480 /
1024x768 / 1280x720 / 1280x960 )
Quality(High/Normal/Low)
Frame Rate ( 1 / 5/ 15 /20/30)
Audio (Enable/ Unable)
Frame Counter Stamp (On/Off)
Timestamp (On/Off)
Device ID Stamp (ON/Off)
Motion Detect Level (High / Medium / Low)
Motion Detect Duration (30sec / 1min / 3min / 5min)
Motion Detect Zone (See illustration. Touch the screen to select desired detect
zone, press again to undo selection. Press OK to save editing)
Microphone Sensitivity
Overwrite(Disable/Enable)

5
5. Date and Time Setting
Select the correct Year/Month/Date/Hour/Minute to set up date and time information
6. Date Format
Select date format between YYYYMMDD / DDMMYYYY
7. Language
Select the language among English
/Simplified Chinese/ Traditional
Chinese/Japanese/ French /Russian
English/簡体中文/繁體中文/日本語
/Francais/Pyccкий

6
7Recording Mode
Set up desired recording mode from the sections.
8Resume to Pre-set Duration
Activate the recording after 15 sec/30 sec according to your selected recording mode.
You could either switch the function off by selecting No.

7
9Timer Recording
This function serves to activate/deactivate the recording regarding the preset date and
time information. DVR must be powered off before the recording is started up.
1. Enter the file to edit timer recording settings
2. Video Line in REC Start
Set up your recording schdules.
Enter date and time information for your recording schedules, and choose the recording
quality. Turn the setting to On at the last item.
DVR will power on and start/stop recording regarding the information inserted.

8
10 Daily timer
Preset your daily recording schedule by inserting time information. Enter
recurrent to set days.

9
11 Backlight Out Duration
Set up back up duration 30 sec / 1min / 3min or choose “No”to turn it off
12 Digital Cam Low Lux
Turn on/off the low lux function of the digital camera
13 Digital Cam NTSC/PAL
Set up NTSC/PAL system

10
14 Storage Option
Touch the screen to choose HDD or SD for storage.
.
15 Storage Information
Click in to view the storage information.
16 Storage Capacity Icon
Turn on the storage capacity icon to display storage

11
17 Format memory
Choose to format hard disk or SD card
18 TV Out Setting
Choose TV Out video system NTSC or PAL
19 TV Out Adjustment
Adjust TVout screen position.

12
20 Display
Touch the screen to choose the LCD/TV/HDMI for the display option.
21 Video Playback
Touch the Screen to choose Playback mode ( Repeat All / All / One / Repeat One)
22 Video Thumbnail
Set up to enable video image preview on the playback list.

13
23 Image thumbnail
Set up to enable snapshot image preview on the playlist.
24 Start Slideshow
Set up if enable slideshow
25 Slideshow Duration
Set up slideshow duration amont 3 / 5 / 7 / 10 seconds.

14
26 Firmware Upgrade
Save the upgrade firmware file onto memory card and touch “firmware upgrade”button.
After the system is updated, it will reboot automatically. If the message “Update Error”
is shown, it means the upgrade is failed due to incomplete file or damaged memory
card. Please use other memory card, or reboot the device after inserting the memory
card.
27 Restor Factory Setting
Select Ok to reset the unit to default values