LawnMaster GT1454 User manual

14’’ Corded Grass Trimmer GT1454
Read all safety rules and instructions carefully before operating this tool.
601 Regent Park Court Greenville, SC 29607, SC 29650 1-866-384-8432
Veuillez lire attentivement toutes les règles et consignes de sécurité avant de faire fonctionner cet outil.
601 Regent Park Court Greenville, SC 29607, SC 29650 1-866-384-8432
Coupe-Bordures Électrique de 14 po GT1454
MNL_GT1454_V1
EN p. 2
FR p. 22
OPERATOR’S MANUAL / MANUEL D'UTILISATION
By Nisha Mistry at 9:54 am, Nov 14, 2018

Contents 2
Product Specifications 2
General Safety Rules
3-5
Electrical Information 6-7
Know Your Grass Trimmer 8
Assembly 9-12
Operation 13-14
Maintenance 15-16
Troubleshooting 17
Warranty 18
Exploded View 19
Parts List 20
Notes 21
2
CONTENTS
PRODUCT SPECIFICATIONS
14” GRASS TRIMMER
Type Corded
Voltage 120 V~60Hz
Amp 5.5 A
Speed 8000 RPM
Line Size 0.065" (1.6mm)
Cutting Swath 14” (355mm)
Net Weight 5.78 lbs (2.6 kg)

3
GENERAL SAFETY RULES
WARNING
READ ALL INSTRUCTIONS AND SAVE THESE INSTRUCTIONS.
When using the grass trimmer the safety rules must be followed. For your
own safety and bystanders please read these instructions before operating the
grass trimmer. Do not use the grass trimmer without reading the instruction sheet.
Please keep the instructions safe for later use.
• This grass trimmer is designed for cutting grass, soft vegetation, and for edging.
• The device is not allowed to be used in public gardens, parks, sports centers or at roadsides as
well as in agriculture and forestry.
• This grass trimmer is not allowed to be used for cutting or chopping, otherwise, there is a risk of
injury. For example:
- Hedges, shrubs and bushes,
- Flowers,
- In terms of composting.
• Never allow children or people unfamiliar with these instructions to use the trimmer.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard.
• Do not wear loose clothing or jewelry. They can be caught in moving parts. Use of gloves and
substantial footwear is recommended when working outdoors. Wear protective hair covering to
contain long hair.
• Stop using the grass trimmer while people, especially children, or pets are nearby.
• Only use the grass trimmer in daylight or good artificial light.
• Ground Fault Circuit Interrupter (GFCI) protection should be provided on the circuit(s) or outlet(s)
to be used for the gardening appliance. Receptacles are available having built-in GFCI
protection and may be used for this measure of safety.
• Before using the grass trimmer and after any impact, check for signs of wear or damage and
repair as necessary.
• Never operate the grass trimmer with damaged guards or without the guards in place.
• Keep hands and feet away from the cutting means at all times and especially when switching on
the motor.
• To reduce the risk of electric shock, use only with an extension cord intended for outdoor use,
such as an extension cord of cord type SW-A, SOW-A, STW-A, STOW-A, SJW-A, SJOW-A,
SJTW-A or SJTOW-A.

4
GENERAL SAFETY RULES
• Keep proper footing and balance at all times.
• Take care against injury from any device fitted for trimming the filament line length. After extending
new cutter line always return the grass trimmer to its normal operating position before switching on.
• Never fit metal cutting elements.
• Never use replacement parts or accessories not provided or recommended by the manufacturer.
• Disconnect the grass trimmer from the outlet before checking, cleaning or working on the grass
trimmer and when it is not in use.
• Only use identical replacement parts when servicing a tool with double insulation. Servicing should
be performed by a qualified technician.
• Always ensure that ventilation openings are kept clear of debris.
• Avoid unintentional starting. Do not carry plugged-in appliance with finger on switch.
• Do not abuse the cord. Never carry appliance by the cord or yank it to disconnect from outlet.
Keep the cord from heat, oil, and sharp edges.
• It will do the job better and with less likelihood of a risk of injury at the rate for which it was designed.
ADDITIONAL SAFETY INSTRUCTIONS FOR YOUR GRASS TRIMMER
• Do not expose to moisture.
• Use only on AC outlets supply voltage shown on the product rating label.
• Avoid operating your trimmer in wet grass, where feasible.
• Do not use in rain.
• On slopes, be extra careful of your footing and wear nonslip footwear.
• Do not walk backwards when trimming, you could trip.
• Always walk when operating the trimmer, never run.
• Switch the trimmer off before going over surfaces other than grass.
• Never pick up or carry a trimmer by the cord.
• Do not lean over the trimmer guard as objects may be throw by the cutting line.
• Keep all nuts, bolts and screws tight to be sure the trimmer is in safe working condition.
• To avoid the risk of injury keep fingers and hands clear of the line cutter on the leading edge of
the guard.
• After use, disconnect the machine from the outlet and check for damage
• When not in use, tools should be stored indoors in a dry and high, or locked-up place – out of
reach of children.

• Corded powered trimmers should only be repaired by an authorized technician.
• Use only manufacturer’s recommended replacement parts and accessories.
• The preparation for use, operation and maintenance of the appliance:
- Keep cutting edge sharp and clean for best performance and to reduce the risk of injury.
Follow instructions for lubricating and changing accessories. Inspect appliance cord periodically,
and if damaged, have it repaired by an authorized service facility. Inspect extension cords
periodically and replace if damaged. Keep handles dry, clean, and free from oil and grease.
- Read the instructions carefully.
- Be familiar with the controls and proper use of the equipment.
- Before use check the supply and extension cord for signs of damage or aging.
- If the cord becomes damaged during use, disconnect the cord from the power supply
immediately.
- Do not use the trimmer if the cords are damaged or worn.
WARNING
5
GENERAL SAFETY RULES
- Cutting elements continue to rotate after the motor is switched off;
- Keep extension cords away from cutting elements.

WARNING
WARNING
6
ELECTRICAL INFORMATION
DOUBLE INSULATED
This grass trimmer has a plug. The grass trimmer is double insulated to provide a double
thickness of insulation between you and the tool’s electrical system. All exposed metal parts are
isolated from the internal metal motor components with protective insulation.
TO AVOID ELECTRICAL HAZARDS, FIRE HAZARDS, OR DAMAGE TO THE
TOOL, USE PROPER CIRCUIT PROTECTION. YOUR GRASS TRIMMER IS
WIRED AT THE FACTORY FOR 120V OPERATION. CONNECT TO A 120 V,
15 A CIRCUIT, AND USE A 15 A TIME-DELAYED FUSE OR CIRCUIT
BREAKER. TO AVOID SHOCK OR FIRE, IF THE EXTENSION CORD IS
WORN, CUT OR DAMAGED IN ANY WAY, REPLACE IT IMMEDIATELY.
USE ONLY IDENTICAL REPLACEMENT PARTS WHEN SERVICING THE
GRASS TRIMMER, TO AVOID INJURY.
WARNING
DOUBLE INSULATION DOES NOT TAKE THE PLACE OF NORMAL SAFETY
PRECAUTIONS WHEN OPERATING THIS GRASS TRIMMER.
CAUTION
ALWAYS MAKE SURE THAT YOUR OUTLET IS PROPERLY GROUNDED.
IF UNCERTAIN, HAVE IT CHECKED BY A CERTIFIED ELECTRICIAN.
WARNING
THIS GRASS TRIMMER IS FOR OUTDOOR USE ONLY. DO NOT EXPOSE
TO RAIN OR USE IN DAMP LOCATIONS.

7
ELECTRICAL INFORMATION
Make sure your extension cord is properly wired and in good electrical condition. Always replace a
damaged extension cord or have it repaired by a qualified person before use. Keep extension cords
away from sharp objects, excessive heat and damp or wet areas.
Use a separate electrical circuit for your tools. This circuit should comprise a wire of at least 12
gauge and should be protected with a 15 A time-delayed fuse. Before connecting the motor to the
power line, make sure the switch is in the OFF position and the electric current is identical to that
stamped on the motor nameplate. Running at a lower voltage will damage the motor.
GUIDELINES FOR USING EXTENSION CORDS
USE THE PROPER EXTENSION CORD. Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one heavy enough to carry the current your product
will draw. An undersized cord will cause overheating. The table below shows the correct size to use
depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge.
The smaller the gauge number, the heavier the cord.
Minimum Gauge for Extension Cords (AWG)
(Using 120 V only)
Ampere Rating AWG
120V
More Than
0
6
10
12
Not More Than
6
10
12
16
25ft (7.62m)
18
18
16
14
50ft (15.24m)
16
16
16
12
100ft (30.48m)
16
14
14
Not Recommended
150ft (45.72m)
14
12
12
Total Length of Cord in Feet (meters)
WARNING
SAVE THESE INSTRUCTIONS.
ALTHOUGH THIS GRASS TRIMMER IS DOUBLE INSULATED, THE EXTENSION
CORD AND RECEPTACLE MUST STILL BE GROUNDED WHILE IN USE TO
PROTECT THE OPERATOR FROM ELECTRICAL SHOCK.

KNOW YOUR GRASS TRIMMER
Components
1. Upper Handle
2. ON / OFF Switch
3. Cord Retainer Hook
4. Assist Handle
5. Upper Shaft
6. Connection Point Locking Pin
7. Lower Shaft
8. Pivoting Head Button
9. Debris Guard
10. Trimmer Head W / Line Spool
11. Trimming Line
12. Flower Guard
13. Motor Housing
14. Rotational Lock Button
The safe use of this product requires an understanding of the information on the product and in this
Operator’s Manual as well as a knowledge of the project you are attempting. Before use of this
product, familiarize yourself with all operating features and safety rules.
8
12
3
2
1
5
6
4
7
8
9
10
11
14
13

This product requires assembly.
• Carefully remove the product and any accessories from the box. Make sure that all items listed in
the packing list are included.
• Inspect the product carefully to make sure no breakage or damage occurred during shipping.
• Do not discard the packing material until you have carefully inspected and satisfactorily operated
the product.
• If any parts are damaged or missing, please call the service center.
9
ASSEMBLY
PACKING LIST
(1) Lower Shaft (with trimmer head and line spool installed)
(1) Upper Shaft
(1) Assist Handle
(1) Bolt
(1) Wing Nut
(1) Debris Guard
(1) Flower Guard
(1) Operator's Manual

WARNING
WARNING
10
ASSEMBLY
FITTING THE GUARD
1. Fit the debris guard into the slots on the trimmer housing and align the screw holes in the debris
guard with those in the trimmer head. Place the guard in position (Fig. 1).
2. Secure the guard with the screws using a phillips screwdriver (Fig. 2).
FITTING THE FLOWER GUARD
1. Pull the flower guard wide enough to extend wide enough to fit over the motor housing (Fig. 3).
2. Insert both ends of the steel bar into the recessed cavities on the motor housing (Fig. 4).
Before assembly, make sure that the grass trimmer is switched off and
unplugged.
Never use the grass trimmer unless the guard is properly fitted.
Fig. 1
Fig. 3 Fig. 4
Fig. 2

11
FITTING THE ASSIST HANDLE
Loosen and remove the wing nut and bolt from the assist handle.
1. Place the assist handle on the upper shaft. Adjust the handle to mount on the index channel as
shown (Fig. 5).
2. Along the index channel, slide the assist handle to the most comfortable position (Fig. 6).
3. Insert the bolt in the hole on the assist handle and tighten the wing nut securely (Fig. 7).
ASSEMBLY
Fig. 5 Fig. 6 Fig. 7
JOINING THE UPPER SHAFT TO THE LOWER SHAFT
1. Align the upper shaft with the lower shaft.
2. Insert upper shaft into the lower shaft and locking pin button into place (Fig. 8).
Never adjust the upper handle while the power head is running. Failure to
stop the motor may cause serious personal injury.
NOTE: If the button does not release completely in the positioning hole, the shafts are not locked
into place. Slightly rotate from side to side until the button is locked into place.
WARNING
Fig. 8

12
PREPARING THE TRIMMER FOR USE
NOTE: Use only approved outdoor extension cords.
1. Attach the outlet end of an extension cord to the plug on the rear of the grass trimmer.
2. Route the extension cord through the slot located on the rear of the grass trimmer housing and
place underneath the cord retainer.
3. To start the grass trimmer, press the on/off switch.
4. To stop the grass trimmer, release the on/off switch (Fig. 9).
ASSEMBLY
WARNING
If any parts are damaged or missing, do not operate this product until the
parts are replaced. Failure to heed this warning could result in serious
personal injury.
WARNING
Do not connect to power supply until assembly is complete.
Failure to comply could result in accidental starting and possible serious
personal injury.
WARNING
Never attempt to lock the on/off switch in the ON position.
Fig.9

OPERATION
HINT FOR OPTIMUM USE
In order to achieve optimum cutting results, only cut dry grass.
TRIMMING
1. Hold the grass trimmer. Gently swing the trimmer from side
to side (Fig. 10).
2. When cutting long grass, work in stages from top to bottom
in small sections. This will prevent the grass being cut from
wrapping around the shaft and spool head.
3. If the grass trimmer starts running slowly, reduce the load.
ADJUSTING HEAD ANGLE
NOTE: This trimmer is equipped with a 7-position pivoting head. The head can be adjusted so it is
easy to access to areas such as under bushes and garden furniture.
1. Depress the pivoting head button and adjust the shaft to the desired angle (Fig. 11).
2. Release the button.
USING THE FLOWER GUARD
If necessary the flower guard can be swung down until it engages. Use the flower guard as shown
to cut around delicate plants or flowers (Fig. 12).
Fig. 12Fig. 11
13
Fig. 10

14
OPERATION
Ŀ
ŀ
䐡
EDGING
NOTE: The best method of edging is performed with the upper handle and assist handle rotated 180°.
1. Unplug the grass trimmer.
2. Press the rotational lock button and rotate the upper handle clockwise (Fig. 13).
3. Release button when the upper handle has been rotated 180° to the edging position.
4. Rotate assist handle 180° and snap onto index channel (Fig. 13).
5. Hold the trimmer with both hands for edging sidewalks and walkways (Fig. 14).
NOTE: The head also can be adjusted to the desired angle for edging.
Fig.14Fig.13
ADVANCING LINE
NOTE: The trimmer is equipped with an auto-feed head.
Do not bump the head or try to advance the line. This will damage the
trimmer and void the warranty.
1. With the trimmer running, release the on/off switch.
2. Wait two seconds, and press the on/off switch.
NOTE: The auto feed function works during the starting and stopping of the
trimmer. The line will extend approximately 3/16” with each stop and start of
the on/off switch WHILE NOT TRIMMING until the line reaches the length of
the grass deflector blade.
3. It may take up to 10 complete starts and stops to advance the line.
NOTE: After each use, clean the trimmer head with a damp cloth to remove
dirt and grime.

Fig. 15 Fig. 16
Your grass trimmer has been designed to operate over a long period of time with minimum
maintenance. Continuous satisfactory operation depends upon proper tool care and regular cleaning.
MAINTENANCE
FITTING A NEW SPOOL
1. Unplug the grass trimmer.
2. Remove the empty spool (Fig. 15).
3. Press the tabs ①and remove the spool cover ②from the cutting head ③. Remove the empty
spool ④from the cutting head.
4. Replace with a new spool (Fig. 16).
5. Release both cutting lines from the parking slot and guide the lines into both eyelets ⑤.
The lines should protrude approximately 4” from the eyelets ⑤.
6. Put the new spool ④into the cutting head ③. Rotate the spool slightly until it is seated.
7. Snap the spool cover ②on the cutting head ③and ensure it is in place (Fig. 17).
Fig. 17
WARNING
Before performing any maintenance, switch off and unplug the tool.
Regularly clean the ventilation slot in your grass trimmer using a soft
brush or dry cloth.
Regularly clean the cutting line and spool using a soft brush or dry cloth.
Regularly remove grass and dirt from the underside of the guard using a
blunt scraper.
15
②
②
③
①
②
⑤
④
④
⑤
①
②
③
③

Fig. 18 Fig. 19 Fig. 20
WINDING NEW LINE ONTO A SPOOL
1. You may wind new cutting lines onto an empty spool.
2. Replacement packs of cutting line are available from dealer.
3. Remove the empty spool from the grass trimmer as described above.
4. Remove any remaining cutting line from the spool.
5. Prepare 2 cutting lines ⑥with the same length for winding. There are 4 eyelets ⑦in the spool,
2 eyelets ⑦in the upper section and 2 eyelets ⑦in the lower section (Fig. 18).
6. First feed 4” of cutting lines ⑥into the two eyelets ⑦. Two eyelets ⑦should be in the different
sections of spool.
7. Wind the cutting lines ⑥onto the spool in the direction of the arrow showed on spool. Make sure
to wind the lines on neatly and in layers. Do not crisscross (Fig. 19).
8. After winding, fix the end of lines ⑥in the parking slot of the spool (Fig. 20).
9. If you want to use, operate as described above to fix the spool on the grass trimmer. Do not
forget to release the cutting lines ⑥from the parking slot.
MAINTENANCE
16
If the cutting lines protrude beyond the trimming blade, cut them off so that they
just reach the blade.
WARNING
Only use the appropriate type of cutting line (0.065” round monofilament).
WARNING
⑦
⑦
⑥⑥

17
If your grass trimmer does not appear to operate properly, follow the instructions below.
If this does not solve the problem, please contact your local repair agent.
TROUBLESHOOTING
Before proceeding, switch off the tool and unplug.
WARNING
PROBLEM POSSIBLE CAUSE SOLUTION
The trimmer
does not start.
The trimmer
runs slowly.
Unsatisfactory
result.
Automatic line
feed does not
work.
The power cord is not properly
connected to power source.
Defective on/off switch.
The spool housing is blocked.
The cutting line protrudes too
long.
The cutting line is worn or
damaged.
Insufficient cutting line.
The spool is jammed.
Replace the spool.
Repair by a qualified personal.
Check that the power cord is properly
connected and that there is power going to
trimmer.
Check that the spool housing can rotate
freely. Carefully clean it if necessary.
Check that the cutting line does not
protrude more than 4” from the spool
housing. If it does, cut it off so that it just
reaches the line trimming blade.
Keep the tabs depressed and remove the
spool cover from the housing. Pull the
cutting line until it protrudes 4” from the
housing. If insufficient cutting line is left on
the spool, install a new spool of cutting line
as instructed in FITTING A NEW SPOOL
section.
Carefully clean the spool cover and
housing.
Remove the spool and check if the lever
can move freely.
Remove the spool and unwind the cutting
line, then wind it on neatly again as
instructed WINDING NEW LINE ONTO A
SPOOL section. Replace the spool as
instructed.

18
WARRANTY
We take pride in producing a high quality, durable product. This Lawnmaster®product carries a
limited two (2) year warranty against defects in workmanship and materials from date of purchase
under normal household use. If product is to be used for commercial, industrial or rental use, a 30
day limited warranty will apply. Warranty does not apply to defects due to direct or indirect abuse,
negligence, misuse, accidents, repairs, or alterations and lack of maintenance. Please keep your
receipt/packing list as proof of purchase. This warranty gives you specific legal rights, and you
may have other rights, which vary from state to state. For product service call Customer Service at
1-866-384-8432.
Items not covered by warranty:
1. Any part that has become inoperative due to misuse, commercial use, abuse, neglect, accident,
improper maintenance, or alteration;
2. The unit, if it has not been operated and/or maintained in accordance with the Operator's
Manual;
3. Normal wear, except as noted below;
4. Routine maintenance items such as lubricants, blade sharpening;
5. Normal deterioration of the exterior finish due to use or exposure.
Transportation Charges: Transportation charges for the movement of any power equipment unit or
attachment are the responsibility of the purchaser. It is the purchaser’s responsibility to pay
transportation charges for any part submitted for replacement under this warranty unless such
return is requested in writing by LawnMaster®.
SAVE YOUR RECEIPTS. THIS WARRANTY IS VOID WITHOUT THEM.

19
EXPLODED VIEW

ITEM NO. PART NO. DESCRIPTION
PARTS LIST
QTY
1
2
3
4
4.1
5
5.1
6
7
8
9
9.1
10
11
12
13
14
15
16
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
121065101
121065102
121063102
121020110
221001117
121030110
121002106
121064103
121064101
121065107
221004107
121002110
121065103
121065108
121065104
121058103
121025107
121065105
121065106
* Parts highlighted in gray are available for after sales purchase.
Handle assembly
Power cord
connection assembly
Switch trigger assembly
Compression spring
Extension Wand Unit
Compression spring
connection assembly
Assistant handle assembly
Rotary handle assembly
Shaft lock button
Compression spring
Motor housing assembly
Motor assembly
Cutting head assembly
Flower guard
Spool assembly
Spool cover
Protector guard assembly
20