leadsun ULTRON AE5 User manual

Made in China AE5.100-C
www.leadsunglobal.com
series
ULTRON
SOLAR STREET LIGHT
www.leadsunglobal.com
INSTRUCTION MANUAL
series
ULTRON
SOLA R ST RE ET LI GH T
INSTRUCTION MANUAL
Phone: [phone] Fax: [phone]
Email: [email protected]
LEADSUN INC.
Phone: [phone]
Address: 35373 Condominium Blvd Zephyrhills, FL 33541.
Email: [email protected]
LEADSUN Australia PTY LTD
Address: 42 Greens Road, Dandenong South, Victoria 3175
Phone: [phone] Fax: [phone] Email:
[email protected]
LEADSUN ISRAEL
Address: LHAV 45 Karmiel Israel 2165448
LEADSUN Global Limited
Address: 3/F, No.1 Workshop, No.15, Pingbei 2nd Road, Nanping, Zhuhai,
Guangdong, P.R. China 519060.
Phone: + Fax: [phone]
Email: [e-mail]

12
Product maintenance
In order to assure that the solar panel receive the light efficiently, please use clear water
to clean the dirt mark on the surface of the panel regularly and prohibit the use of
chemical or abradant which includes chlorobenzene.
Only manufacturer, service agent or qualified personnel can replace the light source or
other circuit components of the lighting device. Without authorization, using the third
party component to replace is prohibited or it would cause serious damage to the
product. if the user disassembles the product without authorization, warranty becomes
void.
If you need to replace the components /accessories, please go to
www.leadsunglobal.com, or contact the local distributor.
Product recycling
Cautions
Transportation and storage
Working condition
Attention to the electric shock
To avoid electric shock, street light with AC adapter must be installed by qualified
electricians and constructors.
The street light with AC adapter is customized product, please confirm the street light
AC adapter is in accord with the local electric supply standard.
Make sure the electric supply power is cut off during the installation and implement
waterproof and insulation protection.
Please read the below cautions carefully before using the AE series solar street
light to avoid physical injury and product failure caused by improper use.
Product protection grade IP65
High tensile structure design can withstand level 3 typhoon (58m/s), beyond this level
damage might be caused to the street light.
Working temperature range from -20℃ to 60℃ (charging temperature is limited within
0℃ to 60℃). The product with heating function can work from -40℃ to 60℃.
The product contains high capacity lithium-ion battery components, please follow the
aviation transport law. Please regard the product as the flammable and explosive
hazardous substance and store it separately from other goods.
The solar panel of the product is fragile, tier limitation is two layers. No stacking out of
limits and No press with heavy stuff.
Store the product under the temperature from 0℃ to 45℃
It should be charged every six months if the product is stored for long time. please use
the special charger to charge the product (the charger needs additional purchase) in
order to avoid battery or device damage.
All internal parts of AE6 are waterproof and rated IP65. Holes and slits on the
luminaires are designed for heat dissipation and drainage. Metal parts are made of
anodized rustproof aluminum, which can withstand high temperatures and humid
weather. However, it is recommended that you avoid installing the street light in areas
with heavy acid mist or salt influx. The strong structural design can withstand wind
speeds upto 180km/hr.
The product is made of recyclable high-performance materials and components, please
don't dispose with other household garbage.
Please understand the local rules about the separate collection of electronics and
electrical products, dispose the waste products in the right way that avoids potential
negative effects to environment and human health.

The Part list is the whole product series functions instruction. The user can look up the corresponding
function according to the purchased product.
Part Description
1
4
2
10
3
Standard
5
34
Gateway type
LORA terminal
No.
Component
Brief description
1
Bird spike
Prevents solar panel contamination from bird droppings
2
Motion sensor
Detects human movement
3
LED light
Lights the area
4
Solar panel
Absorb sunlight energy and transform it into electric power,
control the light by light-operated switch
5
LED and Charging controller
Manage LED light, communication and control charging and
discharging.
6
ON/OFF button
Turn on/off the light, or enter/exit the Transportation mode
7
Type B USB port
For program input
8
Type A USB port / Parameter
Configuration Interface
For battery charging via a 14VDC 1.5A power supply /
Parameter Configuration Interface
9
Infrared remote control receiver
Infrared remote control
10
X bracket
To fix the solar engine
11
Reset button
Restart the gateway
12
USB B port
Gateway program download only
13
Gateway indicator light
Red: gateway working, indicator keeps on;
Green: 4G working, indicator keeps on;
Blue: 4G data transfers, lamp flashing;
Yellow: 4G connection succeed, indicator keeps on.
14
SIM card slot
Insert 2G/4G card
15
2G/4G Module
Wireless network communication
14
LORA Antenna
Network group communication
12
11
13
14
15
16
7
6
8
9
16

Check if all the components are complete before installation, the components and quantity of
each set as follows:
Part List
AE5 solar street light
Tool 1pc
(optional)
Bird spike 2pcs Self-tapping
screw 6pcs
Bracket
hasp 4pcs
M8*16
screw 7pcs
M6 cap
nut 8pcs
M6 spring
washer 8pcs
X bracket
1pc
Product Activation
6
56
In the daytime: When connecting the LED street light to the solar engine, the street light
lights up for 20 seconds, and then turns off. It means the solar street light has been
activated automatically.
At night: Press the ON/OFF button for 5 seconds, and then the LED street light switches
on. It means the solar street light has been activated manually. Then, If you short press
the button, the light will switch between ON and OFF.
*
*
Remarks:
ON mode:
The system will work normally, charging in the
daytime and discharging at night.
Transport (idle) mode:
The solar street light will power off in one hour
and then stay in the OFF mode, for
transportation, storage, or maintenance
purpose, until it’s re-activated.
OFF mode:
The system will not work, charge or
discharge.
Power ON:
a. In the daytime:
The solar street lights gets activated and powered on automatically (i.e. to light up for 20s and
then switch off), once it is taken out of the carton (for the all in one type), or when the LED
street light is connected to the solar engine (for the split type).
b. At night:
Long press the ON/OFF button for 5 seconds to get the solar street light activated manually
(i.e. to switch on), with the solar engine connected to the led light.
* * *
*
*
*
*
*
ON/OFF button
Power OFF:
Press the ON/OFF button for 5 seconds when the light is On, to see the light flashes for 3s and
then switches off to come into Transport Mode; Then press the button for 5s again, or have no
operation for one hour, to have the light flash for 1 second and switch off to get the solar street
light power off.
Switch on/off the light:
When the solar street light is activated and powered on, short press the ON/OFF button, and
then the light will switch between on and off.
OFF
Mode
Transport
Mode
Automatically on in the
daytime, or long press 5
seconds.
ON
Mode
Press 5 seconds
or no operation for
more than an hour
Long press
5 seconds
*
LORA Antenna
1pc (Gateway type and LORA terminal standard)

1
3. How to place the Gateway ?
Road installation
Build wireless solar street light along the road, lamps have to divided into one or several
groups. Each group contains a Gateway and max 120 slave units. The Gateway should
be on the middle of each group.
Village/Factory/Park installation:
For installation at village/factory/park location, the Gateway is recommended placement
on the center of the area.
Gateway street light
120 street lights 120 street lights
Each Gateway covers a range from 800m to 3000m, depends if there are barriers to block signal
transmission. One Gateway can control 120 slave units.
Gateway street light
Gateway street light
2
Before Installation
2. Installation Direction of Solar Panel
Picture 1
Equator
Picture 2
2
1
8
7
Please select the appropriate product according to the installation site’s sunlight intensity and
required operating time. If you are in the northern hemisphere, face the solar panels towards the
south as far as possible when installing the solar street light; if you are in the southern
hemisphere, face the solar panels towards the north. (see picture 1)
For maximum operation efficiency of the solar panels, make sure the sunlight is not blocked by
buildings or trees. (see picture 2)
Dim mode
(30% brightness)
Bright mode
(100% brightness)
1. Working Mode Description
The product default setting controls the light through photo sensing of the solar panel.
The light will turn on automatically when it's dark and turn off automatically when it's bright.
At night it will go into the dim mode when no one is around and turn to full brightness when
motion is detected.

First put the X bracket on the installation frame at the middle of the AE5 solar street light, then
clip the 8 screws into the X bracket slot from the installation frame, last, use the bracket hasp,
M6 spring washer, M6 cap nut to fasten the bracket. (See 1)Picture
1. Install the X bracket
57
Ø85~90
Ø10
Picture 1
Picture 4
10
9
Product Installation
4. Light pole cantilever wire threading
Set the AE5 solar street light installation direction according to the street condition and make
a mark on the light pole. Tapping a 10mm diameter double-sided through-hole 90mm from the
light top in advanced, use for fastening the X bracket. (See 4)Picture
Bracket hasp
M6 cap nut
M6 spring washer
Picture 2
3. Install the bird spike
Using the self-tapping screw in the accessory to fasten the bird spike on the top frame of the
solar power system. (See 3)Picture
Self-tapping
screw
2. 调整灯管角度
用M5六角扳手扭松灯管两端的螺丝，向外转动灯管到适合的角度后，再锁紧灯管两端的螺丝。
(See 2)Picture
Picture 3
M5 tool
o
40
o
40

Product Installation
6. Wireless system installation (Suitable for wireless type)
Gateway antenna intallation
Cautions:
Antenna installation
1
1. Please confirm if the 2G/4G module in the gateway supports the data network covered by the
local carrier before installation.
2. When using the inbuilt 2G/4G module gateway, you need to insert a SIM card which has the
data service. The data service will cause the service fee, and you need to pay the relevant
service fee to the local carrier.
The way to install the antenna has shown below. Attention: please don’t omit the silicone sleeve,
before installation, remove the dust cover from the original antenna first, then put on the silicone
sleeve, install the antenna, and the antenna must be set into place.
Silicone sleeve
Dust cover
LORA AntennaLORA Antenna
LORA Antenna
Dust cover
Silicone sleeve
LORA Antenna
Dust coverDust cover
12
11
5. Mount AE5 on the pole.
Connect the AE5 with the extended cables in the light pole and lock the connectors in turns.
Embed the light pole into the X bracket and use the dedicated tools to fasten 7 M8*16mm
screws. (If you use the electric wrench, torsion should be set to 14N·m)(See Picture 5)
M8*16 screw
LORA Terminal antenna installation
Picture 5

Troubleshooting
3Software operation instruction
Please use LEDSUN EDGE APP to remotely control and configure the street light, visit
www.leadsunglobal.com and follow the steps to Download the LEADSUN EDGE.
A. For APPLE users please go to the APP STORE and install the APP 'LEADSUN
EDGE' .
B. Android cellphone please visit www.leadsunglobal.com or go to the software
platforms like Google Play to download and install 'LEADSUN EDGE'.
C. PC App please visit http://47.52.88.104:8083/Home/Login
With LEADSUN EDGE, you can do the following operation:
1. Register to become a member
2. lighting control
3. History data query
4. Working mode configuration
5. Real-time view.
For detail instructions, please see the "APP User Guide" under "More Functions" in the
software.
Product Installation
14
13
No.
Symptoms
Troubleshooting Steps
Process
1
No light at night
Check that the lamp can be
manually activated.
Refer to "Activation and
Installation" section on this user
guide and run activation tests.
Check if the solar panel is blocked
from the sunlight by houses, trees
and other obstacles.
Clear obstructions or change
installation location.
Check if there is any artificial light
source(s) shining on the solar panel
during the night.
Remove the artificial light
source(s) of interference or
change the installation location.
Examine status of each component
based on the repair guide.
Replace the damaged
component(s).
2
A serious shortage
of working time at
night
Check if the solar panel is blocked
from the sunlight by houses, trees
and other obstacles.
Clear obstructions or change
installation location.
Check if the surface of the solar
panel is dusty or covered.
Clean the surface of solar panels
as detailed above.
Examine if the battery pack is
damaged as per the repair guide
instructions.
Replace damaged battery.
3
Lighting does not
follow the normal
operation mode of
turning on and off
Replace controller(s) and
reprogram.
4
Abnormal motion
sensor
Check if the air temperature close
to human body temperature.
When the air temperature is
close to human temperature,
motion detection may slow down.
It will return to normal after the
air temperature changes.
Check if the installation height is too
high.
It is out of motion detection range
when installation height exceeds
8m. It is recommended to reduce
the height or use other operating
modes.
Check if the motion sensor or
controller(s) is damaged.
Replace damaged motion sensor
or controller(s).
Insert SIM Card
Insert the 4G SIM card into the slot according to the below picture. Press the button next to the
slot to restart the gateway and then cover it with the waterproof plate.
2
Cautions: Ensure the SIM card cutting edge is facing down and the
magnetic stripe is away from the indicator lights.